Search Documents

By Kellerwessel H, Oberheuser

Since its invention by Professor Klaus Schonert of the University of Clausthal, Germany, high pressure rolls comminution has attained near total acceptance as the preferred method of size reduction in the cement industry. Over 300 units have been manufactured worldwide. At locations where the system has been installed, considerable energy savings have been realised. These energy savings are generally in the range of 20 to 30 per cent compared to conventional ball mill circuits. However up to 50 per cent power saving has been achieved at some installations. This technology, with the exception of the diamond industry, has up to now had only limited success in ore processing. This has mainly been attributable to the abrasiveness of ores encountered in this industry leading to high wear rates. These high wear rates have given rise to an unacceptably short life time of the wear surface of the rolls, requiring regular replacement. A new wear surface has been developed which has shown to give a ten-fold increase in service life over conventional surfaces. This, together with developments made in machine design now give the units the ability to attain the high availabilities demanded by the mining industry, and therefore to allow this industry to achieve the considerable operating cost savings offered by the high pressure rolls.

Jan 1, 1992

By Brett D

Tailings disposal and water management are one of the most important environmental issues in mining projects. The nature and the method of disposal of the tailings will determine the long term environmental impacts and must be carefully considered at the planning stage so that final abandonment can be economically achieved. If not, long term and on-going treatment and amelioration may be required to achieve environmental standards. Final abandonment requires dam safety surveillance inspection to satisfy engineering stability and hazard requirements as well as environmental issues. Environmental issues include stability, as well as rehabilitation and long term contamination potential.

Jan 1, 1991

By Stewart A. M, Price D

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings are based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations.

Jan 1, 1992

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

By Horowitz F. G, Lamb P

As mining operations become larger and more complex, larger volumes of geological, geophysical, and production data must be manipulated and interpreted on a day-to-day basis. Because of the large volume of data, more sophisticated data storage strategies, interpretation tools, and visualisation tools must be used by exploration and mining operations in order to remain competitive. Critical to better practice is an understanding of the basic syntax and character of geological and mining data, expressed in the form of a data model. In the short-term, a data model can be used to implement or evaluate schemes for data storage or exchange. It can be used to evaluate software. In the longer term, a data model is essential to the design of the next generation of software for 3D geological modelling. In this and the related paper (Lin et al, 1995) the data model in use by CSIRO is presented, together with: 1. examples of the use of data transfer in the linkage of existing mining software; and 2. examples of the use of the data model in software design.

Jan 1, 1995

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

Recent analysis of backfilling material has shown that a finer size distribution is preferable for stope filling. In order to increase crusher throughput and pit productivity, a reassessment of the quarrying operation was conducted. Part of that reassessment was a review of blasting practice. Six means of reducing the average muckpile fragment size were examined. Different blast initiation and charging options were compared, and patterns using smaller hole sizes were designed, analysed with the JKMRC 3x3o software, then drilled and fired. The ground vibration and face movement was recorded and compared. To determine whether the Kuz-Ram model could be used in an economic analysis of the quarry operation, the fragmentation distribution of the small diameter hole blasts was determined. Photographs of the muckpiles were taken and digitised. However subsequent analysis indicated that a satisfactorily large photo sample was only obtained from the smallest diameter hole blast. The Kuz-Ram fragmentation model prediction was found to be within the confidence limits of those results. An engineering and cost comparison between the blasts was made.

Jan 1, 1995

The extraction of the values from gold bearing clay or clayey ores has always presented difficulties. A description of the successful operation of a mill working on material of this nature is here given in the hope that it will be of interest to mining engineers and metallurgists, particularly as the ore body referred to has been worked out. The methods finally adopted were evolved at the mill after the failure of 3: plant specially designed in England and sent out to New Guinea to cope with the clay by the old principle of calcining to brick followed by crushing and cyanidation. A description is given of the direct cyanidation of run of mine ore in '90 ton vats; which was finally adopted after a great deal of study and experiment. Mention is also made of the method of removing overburden in the open cut and the mining and transport of the ore from the open cut to the mill. The purpose of the paper is to record these matters while the information is still available. . .DESCRIPTION OF THE ORE BODYThe values occurred in a flat-lying lode which had slipped about half a mile down the mountain side and had come to rest in the nearly horizontal position in which it was found and worked. The thickness of the deposit varied from a maximum of about 25 ft. at the northern end to about 10 ft. at the southern end. The ore body was capped with an overburden of decomposed breccia and porphyry of variable thickness the maximum being about 65 ft. The underlying rock, or the footwaIJ of .the flat ore body was breccia locallyknown as blue breccia.

Jan 1, 1951

Perhaps no aspect of the investigation of an ore-deposit is of greater importance to the mining geologist and engineer than a consideration of its geological structure. A thorough understanding of the type, size, shape, and arrangement of any ore-body is essential to the proper conduct of exploratory, developmental, and mining, operations. Significant as these remarks are' in relationship to ore-deposits in general, they become of paramount moment when a complex structure such as the Broken Hill Lode is in question. In this connection the use of the term "lode" as applied to the Broken Hill ore-bodies may terid to confusion of ideas among those not familiar with the field or with the literature pertaining thereto, by reason of the fact that it is generally understood that a "lode" is characterised by simple, tabular form, regular outline, defined walls, and persistent attitude. However, as the terminology is well established by common usage, itsretention appears desirable, and, for the purpose of this paper, the name "The Broken Hill Lode" refers to that complex unit which includes pre-eminently the famous ore-bodies exposed in the workings from the North Mine on the one extreme to the South Blocks (Zinc Corporation) Mine on the other.That the practical value of geological investigation, of the ore-bodies was realised by the Geological Sub-Committee of the late Scientific Society of Broken Hill is attested by the...

Jan 1, 1932

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

The Woodcutters deposit, 65 km south- southeast of Darwin, N.T., consists of a series of veins of pyrite, sphalerite, and galena with some silver, cadmium, antimony, and arsenic minerals. The veins are hosted by the Early Proterozoic Whites Formation, a sequence of black slates with interbedded carbonate rocks and minor ash tuffs. The known orebodies occur about 300 to 500 metres above the contact of Whites Formation with the underlying Coomalie Dolomite, which consists of dolomite and magne- site. The stratigraphic setting is lithologic- ally similar to that of the Mt. Isa deposit, Queensland. The orebodies are replacement veins occ- urring along fault and dyke structures which are sub-parallel to the axes of a double-nosed faulted anticline. The orebodies are in part associated with two unusual carbonatized lam- prophyric dykes. The dykes were intruded after the fold and its slaty cleavage were formed. The ore has replaced the dykes and host rocks and is therefore late-stage hydrothermal miner- alization. The known orebodies are open at depth. A "bonanza" of high-grade ore occurs at the upper part of the largest orebody and is currently the subject of an open cut mine planning study by a consortium of companies headed by Nicron Resources Ltd.

Jan 1, 1984

By Fabjanczyk MW, Guy RJ, Tarrant GC

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992

By Clappison D. J

Since its formation in Papua New Guinea and raising of A$2 million in 1980, Niugini Mining Limited (NML) has grown to a company capitalised on the Australian Stock Exchange at about A$350 million. In 1995 the company produced some 237 000 ounces of gold, 700 000 ounces of silver and nearly 5000 tonnes of copper from its operations at Red Dome, in North Queensland and San Cristobal in The Atacama Desert of Northern Chile. This production contrasts with Niugini Mining's first mining venture at Mt Victor in the Eastern Highlands of PNG which yielded 20 000 ounces of gold and 11 600 of silver between 1987 and 1989. Following the formation of an exploration joint venture in 1982 with Kennecott Explorations (Australia) Ltd, now a subsidiary of RTZ, Niugini Mining's early recognition of the gold potential of volcanic rocks at plate margins led to discovery of the Lihir deposit in July 1982. This deposit containing about 42 million ounces of gold in resources, is one of the largest undeveloped gold deposits in the world. Following raising of equity funds through the float of Lihir Gold Ltd and debt finance in 1995, construction of the mine at a cost of US$673 million is now underway with first full-scale production at approximately 600 000 ounces of gold per year expected in early- 1998.

Jan 1, 1996

By Plumridge C. L, Lynch J. E, Forresty R. J

The Amanda Bel Goldfield (new name) is an area of approximately 1000 sq. km centred 65km WSW of Ingham and 150km due east of Kidston (Camel Creek homestead to Ryeburn homestead area). Gold mineralisation has been located in tightly folded sediments of the Silurian Greenvale Formation as well as in the Early Devonian Kangaroo Hills Formation and the Early Carboniferous Clarke River Formation. The area is traversed by a major NW-SE structural corridor, with many of the numerous basaltic, andesitic and rhyolitic dykes of the region sharing a similar trend. So far fourteen gold-bearing zones have been located, all of which are new discoveries delineated by bulk cyanide leach sampling and subsequent geological reconnaissance. The region has undergone three periods of deformation with gold mineralisation introduced syn-D1, post D1 - pre D , syn-D and post-D2/D , thereby revealing an involved metall~genic history. Mineralisation types include Sb, Sb-Au, Sb-Au-As, Sb-Au-As (-Pb-Zn) and Au-As. Minor occurrences of W, Pb-Zn-Ag and Pb-Zn-Ag-As-Sn are also present as are alluvial (deep lead) tin Drosoects.

Jan 1, 1989

The art of flotation may be divided into two distinct branches, namely:-1. Collective flotation.2. Selective flotation.(1) Collective flotation is applied when all the valuable minerals in an ore are required in one concentrate, leaving ,only gangue minerals in the tailing. The method is applicable, for instance, to such ores as auriferous copper sulphides associated with gangue minerals only, or to silver lead ores low enough in zinc and other valuable minerals.(2) Selective flotation is applied when there are present in an ore two or more valuable sulphides, which cannot be subsequently efficiently treated unless they are separated from one another as well as from the gangue. For example, a silver-Iead-zinc ore, or a copper-gold-iron ore; where the iron is not required with the copper gold concentrate.In order to make these operations practicable chemical reagents have been developed, having power to exert definite actions on the various minerals when brought into contact with them in a water pulp.COLLECTIVE FLOTATION.In order to bring about collective flotation it is generally necessary to add to the pulp a frothing agent and an activator or activators for all the minerals which it is desired to float.SELECTIVE FLOTATION.The object of selective flotation is to activate the mineral which is to be floated, and at the same time to prevent all other minerals from floating.

Jan 1, 1936

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988