Search Documents

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The influence of pulp potential on the flotation behaviour of sulphide minerals in laboratory batch flotation tests is discussed in terms of self-induced flota- tion, collector-induced flotation, and depression.' Assuming that the pulp poten- tial is controlled by the same factors that determine the genuine redox poten- tial, an attempt is made to interpret the experimental results in terms of potential-dependent reactions based on bulk thermodynamic data. Self-induced flotation is displayed by many sulphides in moderately oxidizing solutions but not in reducing solutions. The available evidence suggests that the hydrophobic entity could be sulphur produced by superficial oxidation of the mineral but this has not been established beyond dispute. In general, flotation is observed near the potentials at which sul- phur would be expected to form and the minerals which produce sulphur seem to float the most strongly. Collector-induced flotation is most conveniently studied on minerals which have only slight self-induced floatab- ility. The mineral-collector interaction is potential-dependent hence flotation is generally only observed in limited ranges of potentials. While the general form of the floatability-potential relationship is similar to that predicted from thermody- namic data close correspondence between predicted and experimental results is not always observed.

Jan 1, 1984

By Dunn P. G

The copper ore reserves at the Chuquicamata mine were re-estimated during March to June 1994, as part of a comprehensive audit of the mine's overall short- and long-term planning. The basic principles essential to all ore reserve estimates were implemented viz: 1. A detailed study of the geology, in this case particularly of the orientations of structural features of copper mineralisation and the subdivision of the orebody into geologically homogeneous sections, 2. the use of both drillhole and blasthole data sets, 3. statistical and geostatistical analyses of both data sets to model anisotropic spatial structures for all the geologically homogeneous sections, 4. block kriging using both data sets individually; and 5. a comprehensive validation of the block valuations to confirm the absence of global and conditional biases and to quantify the actual improvement achieved in the overall quality of the estimates compared to those executed on earlier techniques.

Jan 1, 1995

By Sullivan TD, Redman PG

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

The Beverley uranium mine û now in production in the remote north of South Australia at1000 tonnes per annum û was established to meet a projected, but little-recognised shortfallin primary supply of uranium for the nuclear industry in the early part of the 21 st century. Inthe context of AustraliaÆs lack of bi-partisan support for uranium mining and the nuclearindustry, a four to five year window of opportunity existed from 1996 to establish the mine.During this period, Beverley achieved a number of firsts including: the first ISL mine inAustralia; the largest ISL mine in the world and the first to produce more than 500 tonnes ofuranium in its first year; the first to be established under a new Native Title regime in SouthAustralia; and the first to be established under a revised South Australian Mining Act.Beverley was brought into production against the background of: hostile opposition fromanti-nuclear activists; a suspicious and at-times hostile media; a regulatory and politicalcommunity that was unfamiliar with ISL mining; commercially unsophisticated Aboriginalgroups; an inexperienced engineering industry; and the vagaries of development in a remote,semi-arid location with neither population nor infrastructure. The lessons that can be learnedfrom Beverley showed that û like much in life û flexibility and timing are crucial.

Jan 1, 2002

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 µm.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993

It is proposed to consider a new access, mining and hoisting system for underground deposits, as an alternative to the commonly used decline or vertical shaft access. The proposed system offers fundamental improvements in gathering of exploration data, reduction of capital expenditure and significant savings in mine operating costs. The cost reductions are achieved through:superior orebody definition by Supersucker winzing on ore prior to the commencement of capital development; considerable reduction of capital development in waste; full capitalisation on all benefits of a raisebored excavation; introduction of rubber tyred skip and rubber tyred Mine Rapid Response Vehicle; introduction of simplified ore handling system and reduction of underground mobile diesel fleet; and introduction of minimum maintenance shaft concept. The system is applicable to deposits ranging from shallow, low dip angle, narrow vein, high-grade to bigger, massive type vertical mineralisations accessed from the surface, preferably from the bottom of an open pit; it is also suitable as a down dip extension of an existing underground mine. The system is highly conducive to mine automation and emerging trend aimed to increase the ratio of mined metal/mineral to mined waste. It offers substantial reduction in diesel exhaust gas emissions to the mine atmosphere.

Jan 1, 2000

The mechanisms of fragmentation in homogeneous materials and structured rock mass are reviewed. A method previously used to predict vibration damage to the remaining rock is extended and shown to be valid for the prediction of fragmentation in the rock mass removed by blasting. The effectiveness of different explosives in different types of rock blasting is discussed.

Jan 1, 1990

The iron ore mining operations carried out by Goldsworthy Mining Limited at Golds- worthy, Shay Gap and Sunrise Hill, in the Pilbara region of the North-West of Western Australia, are unusual insofar as the ore reserves occur in a number of widely separated and relatively small deposits, requiring deep mining below the water table, and even below sea level at the Goldsworthy pit. This paper has been prepared to describe some of the problems associated with these deep open cut mines, and the technology employed to overcome them, in order to provide an efficient and economical operation. The problems discussed are: 1. Development of the Dewatering System for the Goldsworthy Mine. 2. The Stability of Pit Slopes at the Goldsworthy and Shay Gap Mines. 3. Development of Diesel Electric Trucks for Lonq Uphill Hauls.

Jan 1, 1979

In the stability assessment of open pit walls, geotechnical engineers have to deal with uncertainty related to structural geology, rock mechanical parameters, groundwater and so on. This uncertainty will immediately and significantly impact on wall stability assessment and therefore. influence mineral recovery and ultimately the financial return of open pit mining. However, the conventional factor of safety applied to measure the stability of slopes and the relevant analytical computer packages cannot quantitatively consider the variability or uncertainty of the input data. As a supplement, therefore, geotechnical engineers have begun to apply probability to the stability assessment of open pit walls over the last two decades. To-date unfortunately, no powerful computer package is available to geotechnical engineers to conduct the probability analysis of slope stability. This paper presents a computer package of probability analysis for rock and soil slope stability. In this computer package, the strength parameters of rock and/or soil material such as cohesion, friction angle and unit weight of the different rock and/or soil type domain in a complex structural geology environment can be considered as the basic input random variables. Groundwater level can also be taken into account as a random variable in this package. Two `rigorous' limit equilibrium solutions, the Morgenstern/Price method and the Sarma method, can be used to calculate the factor of safety during Monte Carlo Simulation applied in this program. Five types of probability distribution are included in this package for the user to simulate basic input random variables. Two realistic cases from BHP Iron Ore are used to illustrate this package.

Jan 1, 1997

By Coates J. R, Firth I. C

The Imperial Smelting Furnace at Cockle Creek, NSW, was constructed in 1961 and is the oldest facility using the Imperial Smelting process in operation. In recent years there have been significant improvements in many areas of the operation, including production, safety, hygiene and environmental performance. Steps taken to achieve these improvements are described. Plans to secure a profitable future while meeting environmental requirements are outlined.

Jan 1, 1993

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

By Bishop D. J

The Imperial Smelting Process for the simultaneous production of zinc and lead is probably regarded by the ecologist as a necessary evil with the benefits of its products marginally outweighing the adverse effects of its operation. The purpose of the paper is to examine the environmental impact of the process and to provide information which will demonstrate that the process has considerable indirect environmental benefits and that success is being achieved in reducing direct pollution of the environment by the process. About 12 per cent of the world's zinc and seven per cent of its lead is produced by the process. This proportion will increase with the construction of a new smelter in China. After a brief description of the process the paper considers one of its principal advantages, its ability to treat bulk concentrates. The production of these at the mine can have a number of environmental benefits. Less comminution may be required to separate the metals from the gangue than is needed to separate them from each other; recoveries can be improved in flotation resulting in cleaner tailings dams, less power demand and reduced consumption of potentially hazardous reagents. Simplification of mining and above ground ore handling may also give significant benefits . The process is a considerable consumer of secondary materials such as galvanisers' ashes, copper smelter dusts and materials containing zinc and lead derived from steel plant dusts. The majority of these materials are fed to the blast furnace after hot briquetting. The consumption of secondary materials is a considerable environmental benefit since otherwise they would require to be dumped in secure land-fill sites. The operation of the process itself continues to be subjected to increasingly stringent environmental standards of which examples are provided. Details are provided of lead emissions at Avonmouth showing considerable success in reducing these while increasing production. The slag from the process continues to find many useful applications.

Jan 1, 1993

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988