Search Documents

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

After a short presentation of the Division of Mining at the Royal Insti- tute of Technology, Stockholm, Sweden, the author presents some of-the fill research carried out at the Division. Literature surveys and testing methods and equipment are described. The use of flocculants' in hydraulic filling has been tested both in laboratory and in mines and the results are very promi- sing. Finally compressibility investi- gations and some finite element calcu- lations are presented.

Jan 1, 1973

By D R Van Eck

Western Deep Levels, a seismically active deep level told mine. stalled placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to he extent where installation of mechanical and hydraulic jacks could he Eliminated

Jan 1, 1998

By S Wan, F Zhang, J You, K Tang, X Tang, C Bessada, A Canizarès, Q Zhang, L Lu

Microstructure of CaO-SiO2-based glassy samples with various Al2O3 contents were examined quantitatively by Raman spectroscopy and 27Al MAS NMR (magic-angle spinning nuclear magnetic resonance). Sequence of multiple cluster models of aluminosilicate system modified with Ca2+ and Na+ cations have been designed, and Raman spectra simulation were carried out after geometric optimisation by quantum chemistry (QC) ab initio calculation. The functional relationship between Raman scattering cross-section (RSCS) and stress index of silicon-oxygen tetrahedron (SIT) for aluminosilicates was established, which was applied to the calibration of experimental Raman spectra. Some five-fold coordinated aluminium (AlV, around 5 per cent) and less than 2 per cent sixfold coordinated aluminium (AlVI) were detected by 27Al MAS NMR, while most of aluminium remained in tetrahedral sites (AlIV). The hyperfine quantitative results of Raman spectroscopy and NMR showed a gradually production of AlIV with addition of Al2O3, along with the significant adjustment of Qi species distribution, in which Q1, Q2 reduced and fully polymerised Q4 increased while Q3 showed a non-monotonic variation and obtained the maximum at Al2O3 = 18 mol per cent. Furthermore, the effects of aluminium to bridging oxygen bond types (T-Ob, T = Si, Al) and the degree of polymerisation were also discussed in detail. The evolution of microstructure and its correlation with the viscosity of CaO-SiO2 based melts, incorporating various Al2O3 additives, have been investigated by employing in situ high temperature Raman spectroscopy at 1823 K and viscosity model. These structural features related to composition are essential theoretic foundation to understand their properties. The average Qi evolution culminates in an overall enhancement of the degree of polymerisation. Viscosity was determined utilising a rigorously selected viscosity model, elucidating a consistent upward trajectory as Al2O3 content is incrementally added. Furthermore, a quantitative analysis of the relationship between viscosity and structure was conducted based on the average number of non-bridging oxygen per network-forming tetrahedron (NBO/T). It provides valuable insights for examining and predicting viscosity behaviour of aluminosilicate systems.

Aug 21, 2024

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

In recent years new instrumentation and digital technology have Wrote possible a new facet of goo-physics: broadband seismology. From digitally record-ing networks and arrays. broadband scistnograrns of body waves that are flat to displacement and veloc-ity in at least the frequency range from 0.01 to 5.0 liz can now be routinely obtained for most carthquakes of magnitude greater than about 5.5. In contrast to data from conventional narrowband seismographs, broad-band body waves have sufficient spectral information to nvest,igate the many frequency-dependent eflects that may arise from source finiteness and from wave prop-agat ion phenomenon. Besides the usual parameters of depth. moment and focal mechanism, broadband data have sufficient spectral information to provide estimates of radiated energy, associated stresses and the frequency dependence of source parameters. Moreover. teleseis-mically recorded broadband data and near-field strong motion accelerograms overlap in the frequency band be-tween about 0.1-2.0 Hz. Thus. v it h broadband data it is possible to connect far field and near field data in order to make estimates of acceleration for almost any seismically active region of the circum-Pacific.

Jan 1, 1990

Commercial explosives range from pure emulsions to pure ANFO, with blends of these providing interesting alternatives: energy is often adjusted through addition of aluminium, or the control of density. The energy rating of explosives is derived chiefly from detonation codes, which are used to derive expressions for the internal energy change of the detonation products as they do work under expansion. While all codes used for this purpose work on the basis of Ideal detonation, it is common knowledge that commercial explosives operate in the Non-Ideal domain, which affects the mode of energy delivery to the environment. However, since Ideality represents the foundation from which actual performance evolves, it is valuable to examine the intrinsic energy release of a formulation before attempting to understand the influence of Non-Ideality. In examining the Ideal pressure profile of fundamental formulations, remarkable correlation has been found with field performance, and this increases understanding of the influence of various formulation modifications, especially in regard to the stage at which energy is released, and the effect on rockbreaking. This work has emphasised the value of attempting to understand and define better the non-ideal detonation process.

Jan 1, 2001

By N Donnellan

The Palaeoproterozoic Warramunga Formation is notable as the host to the enigmatic, so-called 'Tennant Creek style' mineralisation. These polymetallic (but mainly Au-Cu-Bi) ore deposits typically have a close spatial association with massive ironstone bodies, and frequently also with banded ironstone, known locally as 'haematite shale'. The Warramunga Formation is a polydeformed, turbiditic succession. Partial, or complete Bouma sequences variously comprising lithic arenite, wacke, siltstone, and mudstone constitute a classic flysch sequence deposited as a proximal (sandstone lithofacies) to distal (siltstone lithofacies) fan association. The Warramunga Formation has a substantial component of volcanic detritus and has generally been attributed to an essentially contemporaneous volcanic provenance. However, lithostratigraphic revision (Donnellan, Hussey and Morrison, in press) apparently precludes outcropping volcanic rocks of the Tennant Creek Block, or indeed Inlier, as the source of detritus. Warramunga Formation geochemistry indicates rapid derivation from a fractionated, predominately felsic igneous source (Palaeoproterozoic upper crust) with a minimum of chemical weathering; together with an admixture of mafic material. Warramunga Formation geochemistry cannot, however, be reconciled with that of the Bemborough Formation, which is here taken to be representative of Flynn Subgroup felsic volcanic rocks. Similarly, the Warramunga Formation is geochemically distinct from Flynn Subgroup sedimentary rocks. Geochemistry of the banded ironstone is consistent with its interpretation as Dine-grained turbidites.

Jan 1, 1994

By D Clarke, I Minniakhmetov

This paper describes the application of the SBRE framework to model the Olympic Dam deposit, one of the largest copper and uranium deposits in the world. Geostatistical simulations are the best practice for quantifying uncertainty in the mineral value chain and estimating resources. However, these simulations are currently undertaken on an ad hoc basis in the mining industry due to the high requirements in computing resources and capabilities in advanced geostatistics. The SBRE project provides a standard framework to test, build, and run conditional simulation workflows, which has been applied to the Olympic Dam deposit. Conventional geostatistical methods face challenges when modelling the Olympic Dam deposit, such as non-stationarity, non-linear correlations, and a large number of grid blocks to simulate. To address these challenges, a combination of methods was used, including projection pursuit multivariate transform, trend-residual decorrelation, pluri-Gaussian simulations, and turning-bands simulations. Various tools and applications were used to build the model, including in-house developed applications, Autovariogram software (Varify), and the RMSP python library. All computations were accomplished on the AWS cloud using the EC2-Batch service. The final set of simulations was validated using various methods, such as grade-tonnage curves, histograms, swath plots, and variogram reproductions, as well as validation using historical samples back-testing. The study highlights the importance of an automated, modular, and scalable framework in the development of conditional simulation workflows and describes the learning gained from trials of different combinations of methods and software

May 24, 2023

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

Ulan Coal Mines Limited operates an underground and open cut mine near Mudgee in the Central West of NSW. The mines are part of a Joint Venture managed by Exxon Coal and Minerals Australia Limited (ECMAL). Currently all the mines output of over five million tonnes per annum is sold into the export market predominantly as a steaming product.

Jan 1, 1993

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By D Q. Zhu

In this paper, the pretreatment of concentrates by roller press was present to improve the granulation of blends comprising some 30 per cent iron ore concentrates and enhance the sintering performance. It is shown that by pretreatment of fine concentrates through roller press, the content of +3 mm fractions of granulation mixture and sinter mixture permeability are elevated by ten per cent and 35 per cent. In the meantime, a sinter productivity increase from 1.51 - 1.62 t.m-2.h-1 is attainted in pot tests with similar sinter tumble index and at lower coke rate. The mechanism of the pretreatment of concentrates process to improve sintering performance of fine iron ore concentrates was demonstrated by mineralogy that better permeability help form more calcium ferrite and good microstructure of sinter, further proven by the better metallurgical performance of sinter.

Jul 11, 2011

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Statistics show that despite a low lost-time accident rate there is a high fatality rate from falls of ground in pillar extraction work. Investigation of accidents indicates that in many cases the planned ex- traction cycle has been ignored. Better training, supervision, and personnel protection and where possible changed systems are suggested as a means of improving safety and achieving better Results.

Jan 1, 1974

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986