Search Documents

By Bell LC

Overburden removal, mining and reclamation are now accepted as the basic operational steps involved in the winning of coal by open cut methods. To attain the lowest operational cost, the recontouring and revegetation of spoilpiles must be planned concurrently with the planning of overburden removal and mining. The earthworks associated with reclamation work on spoilpiles often account for 75 - 90 per cent of total reclamation costs. Experience at Callide Mine has shown that the way that spoilpiles are contoured does influence water retention and can reduce erosion from rainfall run-off. However, provided the recontoured slopes meet'Mines Department specifications, the quality of reclamation work is judged not by the quality of the earthworks but by the plant regrowth on the reshaped surface. Thus it is the quality of the revegetation which is of prime importance. For vegetation to be successful, time must be spent on planned research into methods of overcoming plant nutrient deficiencies and selection of suitable grass and tree species. The research programme undertaken at Callide Mine consists of three stages :- laboratory studies glasshouse trials field trials

Jan 1, 1978

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By Huleatt M, Perkin D, McLeod I, Mock C, Pratt R, Gourlay A, Timoney E, Knight N, Ward J

Generally speaking, Australia's reserves of its more important minerals (in terms of export earnings) are adequate to sustain forecast rates of production to the year 2000. The rate of forecast production increases of these commodities (aluminium - whether as bauxite, alumina or metal, black coal, iron ore and ferro-alloy minerals, base metals, tin, uranium, and mineral sands) reflects a well- ordered and sustained growth phase of Australia's mineral industry.

Jan 1, 1981

By D Clarke, I Minniakhmetov

The Olympic Dam deposit is truly a world-class IOCG-Ag deposit, the world’s fourth largest deposit of copper and the world’s largest known single uranium deposit. Traditional and non-traditional methods have been used to accurately model the geology and mineralisation of the Olympic Dam deposit. Conditional simulation models have long been used as the most robust method for estimating risk and uncertainty in mine planning decisions at other mines around Australia and the world. There are many challenges associated with simulating the Olympic Dam deposit at a selective mining unit size sufficient for underground mine planning purposes. These include the size of the deposit, resulting in hundreds of millions of grid blocks; the disseminated nature of the zoned sulfide mineralisation. And lastly the direct relationship of the relative abundances of the sulfide mineral species that are crucial to the Olympic Dam smelter performance. Several geostatistical techniques have been utilised in the workflow for the Olympic Dam Conditional Simulation model to address these challenges. The key techniques are: • Projection Pursuit Multivariate Transform to de-correlate the main elements before simulation. • Pluri-Gaussian implicit boundary simulation method to simulate the mineralisation domains. • Spectral simulation method of de-trended and de-correlated attributes with account of local varying variance. The resulting conditional simulation models have been validated against histograms, grade-tonnage curves, cross-plots and assessed for variogram reproduction. This paper presents how the final conditional simulation models compare to benchmarking models created using alternate estimation techniques of ordinary kriging and local uniform conditioning. It also presents a validation process using historical samples to test final estimate accuracy of the simulation models.

May 24, 2023

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

Sampling and sample preparation systems at the Hamersley Iron Pty. Limited port of Dampier, W.A., were developed for two separate objectives. 1. The need for rapid determination of physical properties. On stream size analysis enables lump ore and pellet- ized ore physical properties to be monitored and controlled whilst shiploading is in progress. As a control procedure this facility allows optimum shiploading rates con sistent with physical quality control. 2. The need for accurate chemical analysis. Chemical analysis on ship- loading forms the final link in overall quality control procedures encompassing the operation of mining, railway and port blending. Thus maintenance of specification products with minimum variation in chemical characteristics is ensured.

Jan 1, 1976

By Weller K. R, Stewart P. S B, Restarick C. J

The performance of the Renison tin concentrator was assessed in detail for two arrangements of the three available ball mills. With two mills used for primary grinding and the third for regrinding table tailing, the concentrator recovered 65.3 per cent of tin in the three tin concentrates produced by tabling, vanning and flotation at a calculated overall grade of 37.5 per cent tin prior to batch dressing. In the second arrangement one mill was used for primary grinding and two mills for separate regrinding of table tailing and sulphide concentrate. The metallurgical effective- ness of the change was somewhat obscured by unintended changes,i.e. an increase in the assay of the fresh feed from 1.38 per cent to 1.1+6 per cent tin and unresolved changes in the sulphide rougher flotation and tabling. However, using the results from a detailed size by size analysis of the behaviour of ore components in appropriate parts of the plant, it proved possible to show that, had the two unintended changes not occurred, up to 5 per cent

Jan 1, 1977

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By burgess F, Manlapig E. V, Franzidis J. P

Bubble surface area flux, a parameter which is determined by bubble size and superficial gas velocity, has been identified as a criterion for flotation scale-up from a metallurgical point of view. Investigations at Hellyer, Scuddles and Mt Isa

Jan 1, 1997

An ongoing research program into surface subsidence over Room and Pillar coal mining is described. A subsidence monitoring network has been established for one Room and Pillar mine in the West Moreton Coal Field of South East Queensland, at which pillar extraction is being conducted. The maximum measured subsidence to 28 January 1986 was 638 mm, with movement continuing. Analysis of the monitoring data with view to application of the subsidence pre- diction theory developed by Kowalczyk (1972) is discussed. The Kowalczyk theory provides predictions of subsidence depression, slope of surface, horizontal displacement, surface curvature and horizontal strain, for both the Partial and Total Settlement cases. The development of subsidence with time is also investigated and a preliminary analysis conducted.

Jan 1, 1986

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

Thank you for this opportunity to address your conference on The role of coal in the New Zealand energy market".New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government.As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a "true economic market" for energy in New Zealand.

Jan 1, 1990

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By Elford H. S

Australia has many potentially important tin deposits, particularly on the eastern shore of the continent and in Tasmania. A number of these have been worked on a meagre scale, while some of them, because of metallurgical, transport, and other difficulties, have not as yet been developed.Believing that the full development of the tin fields of the Commonwealth of Australia is in part dependent upon the adoption of the most efficient methods of milling and smelting, the Development and Migration Oommission arranged for the first-mentioned author to visit the mining fields of Cornwall, one of the oldest tin-producing districts of the world, and prepare a report for the information of the Commission.This paper, now presented to the Australasian Institute of Mining and Metallurgy with the hope that it will assist the full development of tin mining in Australia, is the joint work of both authors.For over two thousand years tin has been produced from the Cornish mines. Even the ancient Greek historians made mention of tin mining in Cornwall, and it is probable that during the earliest periods the mining was alluvial. As early as 1602 a stamp battery working in Cornwall was described, and in 1671 calcination and buddling was a recognised scheme of treating pyritic ore. In the first half of the 16th century the output of tin from Cornwall was 700 tons per annum, and, from then on, production increased to the maximum in 1914 of 6500 tons. At present (Oct., 1929) the Cambourne-Redruth area produces over 95% of the Cornish tin output. This area includes such mines as the South Crofty, East Pool, Dolcoath, Parkanchy, Polhigey, and Wheal Kitty. The remaining 5% is largely supplied by the Levant and Geevor mines at Pendeen, St. Just area, near Land's End.

Jan 1, 1930

With the sinking of the No. 3 Shaft and the erection of a changehouse nearby, a sub-brace level structure was provided incorporating a time office, underground foremenÆs office and lamp room, in conjunction with a covered walkway, ambulance room, fire station and waiting brace.

Jan 1, 1957

By Porter I, Singh RN

An advanced elasto-plastic finite element model adopting a modified Von Mises yielding criterion was used to simulate progressive failure of the rock strata surrounding a room and pillar mine structure. The model conformed to the strain-softening behaviour of rock and accounted for post-failure residual strength. The simulation was achieved in such a way that material values were updated after each FE run, according to the stress criterion until the solution reached the final equilibrium steady state of the mine structure. The suggested structural stability analysis approach accounted for the main features of the structure degradations produced during loading through changes in rock material stiffness and subsequent evolution of stresses. Comprehensive parametric analysis was performed and the inevitable effect of interaction of the roof, pillar and floor on the overall mine stability limit was investigated. The numerical results clearly showed that linear models could not realistically represent the true behaviour of the mine structure. The results obtained are in good agreement with that predicted in the field.

Jan 1, 1992

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013