Search Documents

By P. St. J. Perrott

AN explosive of balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypoth¬esis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2, 3, 4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large , amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6, 7) and Majima and Takeda (8). These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

By G. St. J. Perrott

AN explosive of, balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypothesis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There: is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into, the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.' It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965

W. H. SHOCKLEY, Chairman, FRANK H.-PROBERT, :Vice-Chairman, T. A. RICKARD, Sec.-Treas.; 420 Market St.,. San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. A Meeting of the San Francisco Section was held on May 7, 1917. Chairman Shockley was in the Chair. The Section was honored by the presence of President Moore and Secretary Stoughton of the Institute. C. W. Merrill introduced President Moore, who then spoke to the Section on the Aims of the Institute. He discussed the possibility of improving the standards of membership by introducing a classification of membership. The present rigid investigation of applicants was pointed out by him. He spoke of the important influence that the local Sections can exert on the Institute and of the importance of sociability and informality at the meetings. Secretary Stoughton, who was introduced by the Chairman, emphasized somewhat the same points. He mentioned the need for making the Bulletin of the Institute more, interesting than it is at present, this to be accomplished by raising the necessary funds by increased advertising. He asked for an expression of opinion on this point. He. said that the employment department of the Institute is now used extensively. At the request of Mrs. Mark L. Requa, Mr. Stoughton. announced that a San Francisco branch of the Woman's Auxiliary of the, Institute was being formed and asked that the ladies of the members' families send in their names to Mrs. Requa or to the Secretary of the Institute.

Jan 10, 1917

By W. E. Hubbard

The Panhandle area of northwest Texas embraces the northern portion of the Permian Basin of Texas as well as a considerable portion of the western part of the Anadarko Basin of Oklahoma. For the purpose of this report it will include in addition to the 20 counties of the Panhandle proper the two tiers of counties lying to the south, a total area of about 32,000 square miles. Crossing the Texas Panhandle diagonally from northwest to southeast is the Amarillo Arch, related to which is all of the production discovered to date. Oil Production Up to Jan. 1, 1930, the Panhandle has produced about 125,000,000 bbl. of oil. The peak yearly production occurred in 1927, during which period 49,000,000 bbl. were produced. In 1928 the production fell to 25,000,000 bbl., but in 1929, on account of important discoveries in Gray County, the total increased to 31,000,000 bbl. To date Hutchinson County has produced 64 per cent. of the total. Table 1 shows the total yearly production by counties. The present production of the Panhandle is 100,500 bbl. from 1745 wells or an average of 57.6 bbl. per well compared to a production on Jan. 1, 1929, of 59,748 bbl. from 1468 wells or an average of 40.7 bbl. per well. The peak production of the year occurred during the week

Jan 1, 1930

Discussion of the paper of THEODORE P. HOLT, presented at the Salt Lake meeting August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1699 to 1708. F. S. SCHMIDT, Salt Lake City, Utah.-Any furnace that can make a chloridizing roast to yield an extraction of 92 to 93 per cent. and do this at a cost of less than 24c. per ton in a 10-ton unit opens great possibilities for the treatment of certain classes of ores. This cost does not include the salt and will be reduced to about 16 1/2c. per ton in the 35-ton furnace which are now being designed. On a trial run the roaster treated 9.6 ton: of Ontario stope fillings crushed to pass a ¼ -in. opening. The ore is well adapted to chlorination with the exception of insufficient sulphur and occasional days of high lime, but is not adapted to any other process The following is an analysis of the crude ore: Ag, 9.52; Au, 0.029 oz. Pb, 0.71; Cu, 0.11; SiO, 79.4; Zn, 0.57; S, 1.00; Fe, 7.9; Mn, 0.89 CaO, 1.20 per cent. The composition of the mix was: Per Cent. Dry crude ore : 83.4 Moisture 4.4 Salt 8.3 Coal dust 2.3 Pyrite, 70 per cent. pure 1.6

Jan 11, 1914

By C. F. Kaiser, T. J. Roberts, I. A. Thomson

The Broken Hill Pty. Co. Ltd. grate-kiln pelletizing plant located at Whyalla, South Australia, produced a total of 250,000 tons of fluxed pellets during 1970. More than 180,000 tons were exported to Japan, while the remainder was used in B.H.P. Co. blast furnaces. The pellet plant treats high grade hematite ore fines and has a nominal capacity of 1.5 million tpy. The induration equipment includes a grate 12-ft 2-in. wide by 164-ft 1-in. long, a kiln 18-ft 6-in. diam by 118-ft 8-in. long, and a rotary cooler 50-ft mean diam by 7 ft wide. Operating problems encountered in the production of fluxed pellets are detailed. The most significant aspect of the trial was the increased production, from about 5100 tpd up to a maximum of 7100, brought about by the addition of artificial magnetite to the plant feed. Laboratory evaluation of fluxed pellets showed that pellets having a basicity ratio (CaO to SiO2) in excess of 1.2 have excellent physical qualities. Reducibility and compressive strength after reduction were both higher for these fluxed pellets than for normal acid pellets. Although it was not possible to publish blast furnace operating data, blast furnace trials on fluxed pellets indicated that production was higher and dust losses substantially lower, compared with similar operations on acid pellets.

Jan 1, 1973

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

By D. M. Beeson, G. D. Ortloff

Water-propelled banks of carbon dioxide recovered both high- and low-viscosity crude oil substantially in excess of that recovered by water flood in linear flow model experiments. The increase in oil recovery is explained by oil swelling and viscosity reduction. Additional oil was recovered by solution gas drive at the end of the carbon dioxide floods when the model systems were depres-sured. This study was an investigation of the use of a water-driven carbon dioxide bank to recover crude oil. Techniques involving the injection of carbon dioxide have aroused con-siderable interest in recent years among methods considered for increasing oil recoveries. A number of investigators have studied the process in the laboratory1-' and in the field.7,5 Laboratory studies referenced indicate that carbon dioxide in conjunction with water flooding recovers more oil than does water flooding alone. These re- ports diverge widely, however, in stating magnitude of improvement. We believed that a water-driven carbon dioxide bank would increase recovery of crude oils by two mechanisms: viscosity reduction and oil swelling. Due to reduction in the oil viscosity caused by solution of carbon dioxide, displacement efficiency should be improved. In addition, the residual oil should be highly swollen by the carbon dioxide held in solution. Thus, the final residual oil saturation, in terms of stock-tank oil, would be lower than in the absence of carbon dioxide. To test this hypothesis, experi-

By Henry J. Williams

The main difficulty in the determination of silicon in pig-irons containing very high percentages of that element, has been due to their almost complete insolubility in acids, or mixtures of acids. The object of the present paper, which presents no new principle, is to suggest a method of determination which has repeatedly given accurate results, and which obviates completely the tediousness and uncertainty of the usual slow solution in acids. This method has been tried with pig-irons containing from 7 to 14 per cent. of combined silicon, and properly called ferro-silicons. When reduced to an impalpable powder in the agate mortar, an 11 per cent. ferro-silicon was found to resist the action of all acids, or mixtures of acids, with the exception of sulphuric acid of about 1.25 specific gravity. But the action of this acid, even during long continued heating, was very slow, 72 hours being necessary to com pletely dissolve half a gramme of the metal. The complete decomposition of 1 gramme of the metal may, on the other hand, readily he effected in a few minutes by fusion with sodium carbonate in a covered platinum crucible over a blast-lamp —the idea being to dissolve the silicon, leaving the iron in condi tion to be readily attacked by acids. The silicon dissolves as soluble sodium silicate, and metallic iron remains in a very spongy and finely divided condition. The addition of a little hot water

Jan 1, 1889

By V. R. Garfias, R. V. Whetsel, J. W. Ristori

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By J. W. Ristori, R. V. Whetsel, V. R. Garfias

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By R. A. Marriot

The steam-generating plant at the Garfield smelter of The American Smelting and Refining Co. consists of two divisions in which the boilers are classed as direct-fired or waste-heat. The direct-fired boiler plant consists of eight 330-boiler hp. type K-19 and S-I 7 Stirling boilers located in the boiler room adjacent to the power house, and two 330-boiler hp. Stirling type K-19 boilers in the reverberatory building, which formerly were connected to a reverberatory furnace but now are arranged for direct firing. All direct-fired boilers are now fired with natural gas. The waste-heat boiler plant consists of all units connected to reverberatory furnaces, and receiving heat from the exit gases therefrom. In this classification there are two 490-boiler hp. Erie City vertical water-tube boilers, and six 330-boiler hp. type K-19 Stirling water-tube waste-heat boilers. Each furnace has boilers arranged in battery setting. The boilers are directly in front of the furnace and connection is made through a short uptake and flue (Fig. 1). The Stirling boiler settings rest on concrete foundations at ground level, with the furnace uptake and flue at a low elevation. The Erie boilers are carried on steelwork some 15 ft. above ground level, and stand against the face of the uptake with no connecting flue. The constructional requirements of a larger furnace dictated this type of setting.

Jan 1, 1934

By Wolfram Ruff, H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ‡ There is, however, a distinct metallographic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others 1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By F. W. Robinson

THE temperature coefficient of electrical resistance of pure metals is high and therefore the resistance increases rapidly with rising temperature. In 1871, Siemens suggested the use of this property as an accurate means of temperature determination. Owing to practical difficulties, particularly the contamination of the metal and consequent permanent change in its resistance and its resistance-temperature relation, this method fell into disrepute as a practical standard until revived later by Callendar and Griffiths, and subsequently by Holborn and Wien, all of whom showed that the earlier difficulties were not inherent in the method but incident to the mode of protection of the resistance coils. Following .the work of these investigators, the problem of temperature measurement by this means has been the subject of careful study and has now assumed an importance second only in practical adoption to the thermo-electric method. It is generally recognized, both here and in Europe, that the standard temperature scale should be the thermodynamic as it permits the evaluation of high temperatures on the basis of the radiation laws of Stefan and Bolzmann, of Rayleigh, and of Wien and Planck, on a scale consistent with that obtained by means of the gas thermometer at low temperatures. Lord Kelvin showed that only. a very small correction, amounting to about +0.7° at 1000° C.-almost within the limits of experimental errors-is necessary to adjust the constant-volume nitrogen thermometer to the ideal thermodynamic scale.

Jan 9, 1919

By K. A. Kiselev, V. I. Zelentsov, V. P. Nebera

INTRODUCTION Most works on flotation of ions and precipitates from solutions have been summarized recently (1-3). Flotation is more desirable than thickening or centrifuging because of higher recovery, productivity, simplicity of apparatus and better economics in general. Electrolytic flotation that utilizes gases is more favorable than other flotation processes because of the following: higher dispersity of gas bubbles, low coalescence of the bubbles, possibility of gradual regulation of the dispersity and other parameters of flotation (4-5). Flotation from solutions is mostly based on the use of alkaline reagents as precipitants (5). Flotation from acid solutions is less common. We used multicomponent solutions with more than 2-3 components, unlike previous research methods. Acidic flotation allows recirculation of solutions to previous operations such as leaching, etc. REAGENTS FOR PRECIPITATION Electroflotation was studied over a wide range of pH with the addition of ferrocyanide, oxyquinoline, hydroxide and carbonate precipitants. In recent works (1,2,6,7) on flotation of Ni, Cu, Zn from alkaline solutions, mostly ferrocyanides were applied. Our choice was oxyquinoline because of the following: 8-oxyquinoline is a nonspecific reagent for many metals, it is readily soluble in acids and alkalis, oxyquinolates of the studied metals are in soluble compounds, the reagent works over a wide range of pH, it is widely available, oxyquinolate precipitates are stable when exposed to air, are readily floatable, and are easily converted to oxides of the metals by sintering.

Jan 1, 1980

By Fred Chappell

Pyrophyllite, a hydrous aluminum silicate, physically similar to talc, receives its name from the Greek word Pyr, for fire and phyllite, a rock or stone. Firestone refers to its first recorded use as firestones or hearthstones. Composition and Properties Pyrophyllite is an aluminum silicate A12O34SiO2H2O (alumina 28.3 pct, silica 66.7 [ ] pct, water 5.0 pct) (Table 1). Vanderbilt1 gives pH value of pyrophyllite as 5.6 to 8.4. Pyrophyllite is usually white or cream, though it may be found in shades of pale green, pale yellow, buff or light gray, and in darker shades and other colors principally due to oxidation of contained iron minerals. It is opaque to translucent in thin sections. Its hardness is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. Its luster is pearly to dull; it is recognized chiefly by its micaceous structure and cleavage, and its soft greasy feel. Two other varieties occur, one in which there are radiated needles in the crystalline form, and there is also a massive homogeneous structure found. Fine grinding reduces pyrophyllite to fiat plates or scales but aggregates of minute foliated plates may be formed.1 Distribution of Deposits Pyrophyllite is found in metamorphic rocks throughout the world but it is only in comparatively recent years that it has assumed much commercial importance. The principal

Jan 1, 1960