Search Documents

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By R. A. Grange, H. M. Stewart

Man.; steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering" and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully understood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually all marten . site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered martensite and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTENSITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1947

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By H. M. Stewart, R. A. Grange

Man.; steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering" and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully understood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually all marten . site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered martensite and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTENSITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1947

By Luc Delaey, Horace Pops

The structure and morphology of thermoelastic and burst type martensitic phases that form upon cooling in Cu-Zn-Si p phase alloys have been studied by transmission electron microscopy. The martensitic phases are composed of a lamellar mixture of two close-packed structures with different stacking sequence, namely ABCBCACAB (orthorhombic) and ABC (fcc). Striations within thermoelastic martensite are most likely produced during interaction with impinging burst-type martensite and not as a consequence of secondary shears. In a study of the martensitic transformation in ternary Cu-Zn based 0 phase alloys1 the dependence of the martensitic transformation temperature, M,, with composition shows variations for elements within a constant valence subgroup and between different subgroups. Such variations are not reflected in a change in habit plane, which is approximately the same for each ternary alloy, namely in the vicinity of (2, 11, 12 Ip. The fact that the habit plane remained constant, despite large differences in M, temperature and electron concentration, suggested2 that the crystal structures of the martensitic phases could be nearly the same. Crystal structures of ternary Cu-Zn based martensites have been determined recently for alloys containing the three-valent elements gallium3, 4 and aluminm. The present studies have been made to examine the structures and morphology of the martensitic phase in ternary Cu-Zn based alloys containing a four-valent element, silicon. I) PROCEDURE Two alloys were prepared by melting and casting weighed quantities of the component high-purity metals in sealed quartz tubes under half an atmosphere of argon. They were subsequently remelted by levitation under a protective atmosphere of argon. After allowing for losses of zinc as determined by the difference in weight before and after casting, the compositions in atomic percent of both alloys were established to be Cu-33.5 Zn-1.8 Si and Cu-27 Zn-5.0 Si. These alloys were homogenized in the P-phase field for 2 days at 800" C. Bulk samples consisted of a martensite phase at room temperature, the M, temperature being approximately 30' and 200" for the 1.8 and the 5 pct Si alloys, respectively. Thin disks were cut from the ingots using a spark machine, and they were heated for 5 min at 800' and quenched into water in order to obtain martensite. These slices were thinned chemically at room temperature in a solution consisting of 40 parts HN03, 50 part H3PO4, and 10 parts HC1 and thinned further electrolytically by the Window technique, using a voltage of 15 to 25 v and a mixture of 1 part HN03 and 2 parts methanol, which was kept at a temperature near -30° c. Foils were examined by transmission electron microscopy using a Philips EM 200 electron microscope. 11) RESULTS AND DISCUSSION 1) Structure and Morphology. Fig. 1 shows the martensitic phase in the alloy containing 1.8 at. pct Si. This phase is composed of contiguous platelets, each containing striations. The direction of the striations changes at the boundary between individual platelets. These internal markings resemble the striations that are usually identified as stacking faults, as for example in Cu-A1 martensites6-a or the lamellar mixture of two close-packed phases in Cu-Zn-Ga marten-sites.3p '9 lo In the present alloys, selected-area diffraction experiments have been obtained in order to determine the nature of the striations. Figs. 2(a), (61, and (c) are electron diffraction patterns of an area inside a single martensite plate. Fig. 2(a) contains diffraction spots which correspond to two close-packed structures with different stacking sequences, namely ABCBCACAB (orthorhombic) and ABC (fcc). Spots belonging only to the fcc structure are indicated by arrows. By tilting the foil either the orthorhombic structure, Fig. 2(b), or the cubic structure shown in Fig. 2(c) may be obtained. When the foil is oriented so that only the diffraction spots of the orthorhornbic structure are present, bright-field illumination shows small lamellae, as seen in Fig. 3. In this figure the lamellae that belong to the fcc structure are bright bands inside the dark extinction contours of the orthorhombic structure. The boundaries of the lamellae are parallel to the basal planes of the orthorhombic structure and to the {Ill} planes of the cubic structure, the close-packed directions of both structures being parallel. The 5 pct Si alloy shows similar features as those described for the 1.8 at. pct Si alloy.

Jan 1, 1969

By E. C. W. Perryman

The wide grooves formed at the grain boundaries when high purity aluminum is attacked by hydrochloric acid or sodium hydroxide have been attributed by earlier workers to the high energy of the grain boundary material. The effect has been investigated for high-purity AI-Fe alloys with up to 0.055 pct Fe as a function of iron content and heat treatment. It is shown that the explanation given above is untenable, but that the results can be explained on the assumption that iron segregates to the grain boundary in solid solution. IN 1934, Rohrmann¹ showed that aluminum of 99.95 pct purity suffered intercrystalline corrosion when immersed in 10 to 20 pct hydrochloric acid, and that the susceptibility to intercrystalline corrosion depended upon the heat treatment given. The greatest susceptibility was found for specimens quenched from a high temperature (600°C) and the lowest susceptibility for specimens cooled slowly from that temperature. Lacombe and Yannaquis2 have shown that super-pure aluminum (99.9986 pct) annealed at 600°C suffers intercrystalline attack in 10 pct hydrochloric acid and that this attack is intensified by anodic dissolution in the same solution at a current density of 10 milliamperes per sq dm. No difference in extent of intercrystalline attack was found between the 99.993 and 99.986 pct Al, which led the authors to suggest that impurities played only a secondary role in the mechanism of intercrystalline corrosion. It was found, however, that the attack at the grain boundaries depended upon the relative orientation of the grains, large differences in orientation favoring rapid attack. Boundaries where the two neighboring grains were similarly orientated showed high resistance to attack as did boundaries between grains which were in twin relationship. These observations led Lacombe and Yannaquis to suggest that the intercrystalline attack was due to lattice discontinuities present at grain boundaries. Assuming that the grain boundary is a layer three to five atoms thick and has a crystal structure which is a compromise between the two neighboring grains it is clear that the discontinuities will increase with increasing difference in orientation between the neighboring grains and hence the increasing tendency to intercrystalline attack. Roald and Streicher³ investigated the effect of heat treatment of aluminum alloys ranging in purity from 99.2 to 99.998 pct on the corrosion resistance in 20 pct hydrochloric acid and 0.30N sodium hydroxide. They found that in hydrochloric acid the intercrystalline attack appeared to be determined by the type and quantity of impurities present and by the relative orientation of the grains. No difference in the susceptibility to intercrystalline attack was observed between specimens quenched and those furnace cooled, from 575°C. In 0.30N sodium hydroxide some materials exhibited intercrystalline attack, this taking the form of V-notches. Rohrmann¹ offered no explanation for the greater susceptibility to corrosion of material quenched from 600°C. It seems possible that this difference is connected in some way with a different distribution of impurity elements in the quenched and slowly cooled specimens. The fact that Roald and Streicher8 observed no difference between quenched and slowly cooled specimens may possibly be due to differences in either rate of cooling or silicon content or possibly both. Both these would be expected to have an effect on the distribution of impurity elements. Although the rate of cooling used by Rohrmann was slightly more rapid than that used by Roald and Streicher the position cannot be clarified because Rohrmann does not give the silicon content and Roald and Streicher give the silicon contents of only a few of their alloys. That Lacombe and Yannaquis2 found no difference in corrosion behavior attributable to impurities between the two materials they used may be because both were of high purity compared with the aluminum used by Rohrmann.¹ Although they found no difference in the corrosion behavior of their two materials it is possible that the results obtained by Lacombe and Yannaquis may, nevertheless, have been influenced by impurity distribution, since, on the transition lattice theory of grain boundary structure, it would be expected that sparingly soluble impurities would tend to segregate to boundaries where the orientation difference is such that there is a greater density of atomic sites of suitable size to contain them. It was considered worth while, therefore, to examine the corrosion properties of a series of materials of differing impurity content with the objects of confirming the experimental observations made

Jan 1, 1954

By Andrew B. Allen, Charles W. Robinson, Robert L. Schneider

In April, the US Synthetic Fuels Corp. broke a three-year silence and made its first financial award by approving a $820,750 loan for the First Colony peat-to-methanol project in North Carolina (ME, May, page 403). Peat Methanol Associates (PMA), a partnership between Koppers Co., ETCO Methanol Inc., Transco, Peat Methanol Co., and l. B. Sunderland, broke ground at First Colony last year and plans to begin production in Dec. 1985. Although the award is only a small part of Synthetic Fuels Corp.'s $15-billion budget, it does signal the corporation's intention to move aggressively ahead. It also is a positive indication that First Colony will be completed and operated successfully. This article describes the methods and equipment that will be used to harvest peat at First Colony, as well as how the peat will be converted to methanol. Introduction Peat deposits found along North Carolina's coastal plain contain high-quality fuel-grade peat with an average heating value of more than 23.3 MJ/kg (10,000 Btu/lb) (dry), with a low sulfur and ash content. The deposits differ from other US peats in that they contain large, sound Atlantic White Cedar and Cypress logs, stumps, and roots that may extend throughout the full depth of the deposit. A second difference is that these deposits are much more highly decomposed and, in the raw state, have the appearance and feel of a heavy, reddish-brown grease. These factors make it impractical to use standard production equipment so a new line was developed. Also, because of these conditions, techniques were modified to facilitate production. First Colony Farms, located near Creswell, NC, developed and evaluated a milled peat program. Equipment for this production method was designed and built, production rates were established from field operations, drying rates were established, weather data were analyzed, and total operating and capital costs were estimated. The method depends on the sun and wind for drying peat to the desired moisture content, in this case around 40%. Therefore, field preparation is actually the construction of a large solar collector to dry the peat so it can be harvested and stockpiled. It is essential that this collector be properly profiled initially and maintained during production to prevent precipitation from ponding. Initial Field Preparation Initial field preparation includes cleaning existing canals and constructing ditches and water control structures for proper drainage of rainwater run-off, building adequate roads for site access, removing surface vegetation, and profiling and sloping the fields. At First Colony, the 60.7-km2 (15,000-acre) harvesting area was divided into 129.5-hm2 (320-acre) blocks about 1.6 km (1 mile) long and 805 m (0.5 mile) wide. This was accomplished by cleaning main outfall canals with adjacent roads built from canal spoil at 1.6-km (1-mile) intervals. Existing intermediate canals that feed into main outfall canals at 805-m (0.5-mile) intervals also are cleaned. Headland roads are constructed from canal spoil along each side of each intermediate canal. This 129.5-hm2 (320-acre) block is then divided into 32 harvest strips by small V-ditches constructed at 50-m (165-ft) intervals. At the end of the field with the lowest elevation, corrugated steel pipe culverts are installed under the headland road in each V-ditch to control rainwater runoff into intermediate canals. Runoff water from the fields is diverted to a holding pond to prevent any increase in peak water runoff rates and to allow for more uniform drainage rate than experienced to date. After the drainage system is installed, harvest strips are ready for grinding and sloping operations. Surface vegetation, made up of small, waxy-leafed shrubs such as Gallberry, Bayberry, Magnolia, and scattered pond pine, can be effectively ground and incorporated into the upper surface of the peat layer. Here, it will rapidly decompose and have little effect on overall peat quality, thus eliminating the standard practice of pushing the vegetation and upper wood layer into long windrows with bulldozers and hauling this debris from the fields. Incorporating vegetation into the upper surface is known as the initial 102-mm (4-in.) surface vegetation grind and is accomplished by using a modified Bros Rota Mixer. Following this operation, and by using the same unit, a sec¬ond grind with a depth of 200-255 mm (8-10 in.) is made. This reduces the debris to a finer consistency, mixes it with the upper peat layer, and grinds any wood found in the upper 200-255 mm (8-10 in.). After initial grinding operations are completed, the augering or sloping operations can be accomplished with little or no hin-

Jan 7, 1983

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981

By G. F. Leaming

The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. ? Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Learning for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Learning's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Learning is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed. ?

Jan 1, 1986

By W. A. Haley

The use of diesel engines in underground hard-rock mines dates back to the late 1940s. For the first several years, they were used only occasionally, being limited to a few metal mines that experimented with crawler¬mounted front-end loaders, tractor-trailer hauling units, a few tractors for drill-compressor mounts, and utility cleanup machines. By the mid-1950s, track loaders had become commonplace in limestone mines and uranium mines on the Colorado Plateau in the United States, as well as in Canada. Use of crawler-mounted tractors as drill and compressor mounts also increased. By the end of the 1950s, rubber-tired loaders and some haulers began to replace the track-type machines and rail-mounted cars that had been in use. About 1960, the rubber-tired machines brought about a new era of underground mining mobility and flexibility, centered on a method commonly known as "trackless mining." Ultimately, many of the underground rail-type systems for loading and hauling were replaced by the trackless mining technique. ECONOMIC CONSIDERATIONS The size and nature of mineral deposits, plus ground control techniques, historically had dictated small open¬ings to the surface from many underground mines. The small mine openings led to the development of special rubber-tired loaders and haulers designed specifically for access through the small openings. However, some mines, particularly those in massive mineral deposits, are able to excavate and maintain very large openings, and some use modified room-and-pillar systems. With the large mine openings, the use of larger, more produc¬tive equipment such as that commonly found in surface mining becomes economical. In fact, productivity gen¬erally increases at a more pronounced rate than machine size increases because many of the larger machines were designed for heavy-duty shot-rock applications in surface mines and construction sites where the handling of blasted rock is common. Table 1 can be used as a very Table 1. General Productivity Comparison for Conventional Machines In Underground Use (Shot-Rock Conditions) 2.3 m3 (3 cu yd) 4.6 m3 (6 cu yd) Loader Loader Expected Surface 230 t/h 540 t/h Production (250 stph) (600 stph) Expected Underground 90 t/h 270 t/h Production (100 stph) (300 stph) Expected Total Efficiency: Surface 40%-60% 50%75% Underground 25%.-40% 30%50% Expected Useful Machine 8000 hr 12,000 hr Life Before Replacement general comparison of the production and efficiency between small and large machines. Combining greater productivity often inherent in larger machines, with reduced downtime resulting from using fully developed machines with fast parts and service backup, some mine operators have been able to reduce material handling costs appreciably while reduc¬ing manpower requirements for operators and main¬tenance men. Large mine openings increase the amount of rock that must be handled in the development work, and they sometimes increase the dilution in stopes or rooms, de¬pending upon the dimensions of the ore zone. Providing adequate space for the unrestricted operation of large surface mining machines could, therefore, lead to more waste segregation and handling costs. It could also cause greater ore dilution that would result in a lower grade of ore being delivered to the processing plant. The tradeoffs between opposing cost factors must be reconciled and balanced to achieve the best overall cost of the crude ore, concentrates, or product. EQUIPMENT MODIFICATIONS Loaders and haulers designed for surface mining are seldom used underground in their standard con¬figurations without some modifications. If done, the modifications generally are made by the equipment dealer and/or the user, and the modifications usually include one or more of the following items: 1) The exhaust stack is lowered, and its direction is changed. Usually, it is repositioned horizontally to the rear, or it is fed into the engine fan to diffuse the exhaust gases. 2) The operator's position is lowered by either lowering the seat or changing the seat to a side mount. 3) The operator controls are adjusted to fit the new operator position. 4) Other components, such as the radiator and loader tower, are lowered. 5) Special bumper guards are mounted at the base of the radiator area. 6) An exhaust conditioner is mounted and con¬nected, using either a catalytic or a water-type condi¬tioner, or both. This usually is controlled by the safety and health regulatory authority having jurisdiction. 7) The positions of other components are rearranged

Jan 1, 1982

By C. G. Dunn, M. Sharp

IN twinned crystals of the face-centered cubic metals the lattice of one twin is a mirror image of the other in a common twin boundary. When several twins appear within large grain in a sheet specimen, the twin one boundaries form a set of lines at the surface of the specimen which coincide with (111) planes of the large grain. Furthermore, for twins of the same orientation, these lines are parallel. Generally, the presence of identically oriented regions with straight parallel boundaries coinciding with a (111) plane of the surrounding crystal is strong evidence for identifying the island regions as twins of the parent crystal. However, Fig. 1, which shows the macrostructure of a large grain of copper with island regions that satisfy these conditions. is not an illustration of (111) twins. Since the reverse side of the specimen has much the same appearance, it was thought at first that these regions, which appear dark in the macrograph, actually were twins. According to X-ray data, however, these regions are second-order twins of the large crystal. With regard to their formation, these second-order twins formed by secondary recrystallization in a cube texture matrix. Growth occurred in the direction of the arrow (see Fig. 1) as the specimen moved slowly into a gradient temperature furnace as described previously.' Nucleation of the second-order twins occurred, therefore, on the ends facing opposite the arrow. If the origin of the second-order twins were due to repeated twinning, some first-order twin structure should be visible on these ends. This proved to be the case, as very small twins were readily found with the aid of a microscope, and probably could have been seen, in some instances, under ideal lighting conditions without aid of a microscope. Fig. 2 shows a cross-section view taken perpendicular to both the surface and the (111) trace of the parent crystal (visible as a straight boundary in Fig. 1) at the beginning point of growth of a second-order twin and where one first-order twin was relatively thick. In the micrograph, A is the large parent grain; B is the first-order twin of A; and C, which is a first-order twin of B; is a second-order twin of A. Between A and B and between B and C the major straight portions are traces of common (111) twin boundaries. The straight portion of boundary between A and C, however, is not a common crystallographic plane to the two lattices; it is a (111) plane of A and a (115) plane of C. Without considering the mechanism of twinning itself, the origin of the second-order twins may be accounted for in terms of repeated twinning and special growth characteristics. After each nucleation, a selective growth process can be thought of as favoring growth of the first-order twin in local spots only and favoring growth of the second-order twin to an extent comparable with that of the parent grain over relatively large areas in a way similar to that described for twinning in aluminum.' It has already been pointed out that the boundary between the large grain (A) and the second-order twin (C), which is responsible for the straight boundary portions in Fig. 1, involves a (111) plane of A and a (115) plane of C. The same combination of planes is not only possible in first-order twins, but actually appears quite frequently.3 Their prevalence in first-order twins and their presence here in second-order twins, together with the necessary occurrence of a large number of common lattice sites at the boundary, is an indication that this combination produces an "energy cusp"' boundary. (Energy cusp boundaries have been described by Shockley and Read.") The configuration of atoms near a {Ill), (115) boundary in first-order twins is of course different from the configuration near the same type of boundary in second-order twins. References 1 M. Sharp and C. G. Dunn: Secondary Recrystallization Texture in Copper. Journal of Metals (January 1952) Trans. AIME, p. 42. 2W. G. Burgers and W. May: Stimulated Crystals and Twinning in Recrystallized Aluminum. Recueil des travaux chimiques des Pays-Bas (1945) 64, p. 5. aD. Whitwham, M. Mouflard, and P. Lacombe: Discussion of W. C. Ellis and R. G. Treuting, "Atomic Relationships in the Cubic Twinned State." Trans. AIME (1951) 191, p. 1070; Journal of Metals (October 1951). 4 W. Shockley and W. T. Read: Dislocation Models of Crystal Grain Boundaries. Physical Review (1950) 78, p. 275.

Jan 1, 1953

By R. A. Walker, G. Scheltgen, T. Javorsky, G. Blackwell

"Recent engineering advances in open pit rock mechanics have resulted in improved pit wall slope design and improved operating procedures in the event of a major wall instability. At the other end of the spectrum, on the scale of single bench failures, considerable discretion is left to the mine operators as to how potential problems are handled. The usual alternatives are either to operate with caution beneath potential hazards, or try to bring the unstable rock down. In specific cases it may be advantageous to attempt to stabilize rock structures for reasons of access and operating safety.A t the Brenda Mines open pit a prominent structure on the north wall had caused recurring bench-scale wedge failures when exposed on each mining level. In spite of operating precautions a shovel was hit by a rockfall causing significant damage. The first section of this paper describes the investigative, design, and stabilization methods which permitted subsequent mining beneath the structure to proceed without incident. Emphasis is placed on the personnel and equipment resources available at the mine site which were used to minimize costs and which would be available at most operating mines.The second section describes an ongoing research project that utilizes radio telemetry to transmit slope monitoring data. As part of this project the wedge structure was instrumented so that it could be continuously monitored with the aid of a computer. The application demonstrated the potential of 'micro- chip' technology to remote data collection and processing as related to rock structure monitoring, slope stability and safety."

Jan 1, 1989

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By R. E. Miner, J. K. Jackson, T. L. Wilson

A study has been made of the transformation kintetics and morphology in gas-quenched Fe-5 pct Ni alloys. Massive ferrite or nlurtensite was found to form at temperatures in agreement with earlier results. Surface Preparation appeared to have the greatest effect in determining the type of transformation Product formed. Grain size change, subgrain morphology, and dislocation densities of massive ferrite were essen-tinlly invariant functions of cooling rate. The mar-tens~tic structures were typical of transformation in austenite grains of the order of the sample thickness. BY introducing the idea of a massive transformation in dilute iron-base alloys, Gilbert and Owen in 1962 served to stimulate a closer inspection of phase transformations in ferrous systems.' A wealth of literature has followed concerned with the morphology,2-5 transformation mode,2'3'6-8 and thermodynamics of transformations.2,5,9 interesting controversies have resulted from the experimental observations; closer attention has been paid to the definition of massive transformations and still to be resolved is the Ms temperature of pure iron. The purpose of this note is to report some observations made in a detailed kinetic and metallographic examination of the transformations that occur in gas quenched Fe-5 pct Ni. The results are pertinent to the Ms extrapolations that have been made for pure iron and the observed substructure of massively transformed alloys. PROCEDURE The material used in this investigation was cast as a 5 lb vacuum induction melted, carbon deoxidized heat. The ingot was hot worked to a strip 0.10 in. thick, decarburized, and cold rolled to final thickness. Specimens were punched to sample shape and decarburized in wet hydrogen at 600°C. The chemistry of test specimens is indicated in Table I. Samples 1 by $ in., by thickness were resistance heated and rapidly cooled in an apparatus as illustrated in Fig. 1. Similar helium quenching apparatuses have been described previously;2,6'10 the distinguishing feature of this apparatus is the nozzle geometry. Twin nozzles with three convergent-divergent, sonic ports were mounted perpendicular to the specimen for quenching purposes. The specimen temperature was monitored with an intrinsic 3 mil chromel-alumel thermocouple spot welded to the specimen and con- nected to an oscilloscope. A single switch stopped the current flow through the specimen, opened a gas flow solenoid valve, and initiated an oscilloscope sweep. Cooling rates were read directly from a photograph of the oscilloscope trace and the quenching rates quoted later were made at a point immediately prior to transformation on the trace. All quenching studies were conducted either under a vacuum of 10"-5 torr or a helium atmosphere. The sample geometry was chosen large enough to permit optical and electron microscopy to be performed on samples. The samples were electropolished for both types of examination in a perchloric-acetic solution. Electron microscopy was conducted on a HU 11A microscope operated at 100 kv. Dislocation densities were determined at the same general operating reflection (110) on foils thick enough to produce Kikuchi patterns. RESULTS AND DISCUSSION Transformation Temperature Observations and OD-tical Microscopy. The quenching results of this study are illustrated in Fig. -2(a). Samples which were treated in the as-decarburized condition transformed in a manner similar to that reported previously—a decrease in transformation temperature occurred as the quenching rate increased until a plateau region was reached. Within the scatter of the results obtained here, there was no break in the transformation temperature-quenching rate plot. This suggests no change in transformation mode. Further metallographic examination confirmed this observation. A martensitic transformation was obtained for similarly treated samples except that the surface was first electropolished. The Ms temperature was approximately 85°C below the plateau determined for the unpolished samples and cooling rates as slow as 2000°C per sec were adequate for producing marten-site. The transformation temperatures are in gen- / STRIP SAMPLE / COPPER I SAX/-/}' / CONNECTOR-----A f, SON|C poRTS AC LEADS 3j ]j"I rofe[ \ Mf/yinK/iKj''^ THERMOCOUPLE X-(^—iie"s*c? ' LEADS 1 INCH Fig. 1-—Schematic scction of gas quenching apparatus

Jan 1, 1970

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of' carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction'; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8'9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By M. D. Hassialis, C. G. Myer

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1—The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2—The orientation of the chemical units at the surface; and 3—The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element—the mobility of the collector units in the two dimensions of the solid-liquid interface. Regardless of the viewpoint adopted as to whether the chemical units comprising the collector film are collector ions or molecules, held either by chemical or physical forces, the writers on flotation theory are in apparent agreement as to the orientation of the chemical units at the mineral surface. Wark and Cox' showed that the contact angle at a stable collector-coated surface in a constant chemical environment is independent of the nature of the mineral and of any resurfacing agent; it depends solely upon the collector used. They showed further that the value of the contact angle increases with the number of carbon atoms in a homologous series of compounds. Taggart, Taylor, and Knoll2 postulated that the collector ion is oriented with the chemically reactive, polar end toward the mineral surface and the non-polar, hydrocarbon-like end toward the liquid phase. In support thereof they cited the abstraction of p-p1 dihydroxydiphenylthiourea and of glycol xanthate8 by galena without a concomitant increase in the contact angle above that of clean galena. It was argued that in these cases the water-repellent layer which normally would be presented to the liquid phase owing to the orientation of the collector ions is overlain by a layer of water-avid groups, the hydroxyl groups. Implicit is the analogous orientation exhibited by a monomolecular layer of an insoluble substance at an air-water interface. It should be pointed out that these facts also are consistent with the concept that the collector units be flat on the surface of the mineral and that the response of the surface to an air bubble is determined by the ratio of the area covered by water-avid groups to the area covered by water-repellent groups; the areas being weighted according to the relative watef-avidity or water-repellency of the groups involved. The disposition of the chemical units of the collector film at the mineral surface has not received the attention it merits. Taggart4 concluded from the observed stoichiometry of the ions entering and leaving a surface that the stoichiometry is obeyed in detail at the surface of the mineral. Thus, in the case of xanthate-coated galena, pairs of xanthate ions are attached to surface lead ions. In the case of chemisorption, Gaudin and Preller postulated an agreement between the atoms or ions of the substratum (the mineral surface) with those of the superstratum (collector film); in the case of the physical adsorption their position is not clear. In one place they state "the first type (physical adsorption) does not require any agreement between the atoms or ions of the substratum with that of the superstratum" and in another place that "It seems, in fact, as though some slight influence of the substratum is formed even in physical adsorption." The present work shows that in some cases of chemisorption the chemical units of the collector film are in constant surface-bound motion and may not be assigned to any site of the surface, hence there is no permanent association between the chemical units of the film and the atoms or ions of the solid. The physical property of the collector film that is of paramount importance is its surface energy. Although this property is not susceptible to direct experimental determination, the related contact angle is. Much of the knowledge of the properties of a collector film derives (by deductive and inductive reasoning) from the behavior of an air bubble thereat

Jan 1, 1952

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981

By E. Wainer, K. D. Burnham

A wet beneficiation technique for producing wollas-tonite from its ore in high yield and purity has been evaluated in a pilot plant operation at the rate of 75 tons per month. Finely crushed, unsized wollastonite ore mixed with water is passed through a high in tensity oscillating wet magnetic separator of unique design and in a single pass over 90% of the wolla-stonite exhibiting a crystal purity of 99.8% is obtained irrespective of size of feed fraction. Thereafter, the material is processed by closed cycle standard wet milling and classification techniques to yield a 1µ size product, though any mesh size up to and including 50 mesh may be obtained, if desired. Costs appear to be significantly lower than those available from dry processed techniques. Wollas tonite made by this unusual wet process appears to have potential utility in the following fields: ceramics, paints, plastics, paper, organic finishes, reinforcement of portland cement items, controlled porosity refractory ceramic foams, cinder and concrete block paint, and the like. The 1µ and certain chemically processed varieties of wollastonite may have unusual utility in the paper industry both as a filler and as a coating material and in the organic finish industry. Extensive deposits of wollastonite ore equivalent to an average tenor of 50% to 60% of this latter mineral in easily separable form exists in and around Essex County in northern New York State in reserves of the order of several tens of millions of tons. While important portions of these deposits are susceptible to open pit mining techniques, one operation near Wills-boro, N.Y., involves tunnel mining and dry milling and beneficiation techniques. This mill and tunnel mine is presently being operated by The Cabot Corp. and a variety of particle sizes are now sold into markets in the ceramic, paint, plastic finish, floor tile and in similar fields in substantial tonnages on a repetitive basis. Serious investigation and study over the past several years has indicated that, outside of the obvious economies of open pit techniques for mining purposes, wet beneficiation and milling procedures applied to the ore not only represent a potential for greater economies in the production of a superfine finished product but yields products of improved properties exhibiting increased market potential which may not be available from the dry ground product. The Lewis and Deerhead deposits, controlled by the Adirondack Development Corp., appear to be identical to the Wilisboro deposit. Utilizing ore taken from the Lewis and Deerhead deposits, a pilot plant process for the wet beneficiation, milling and classifying of wollastonite ore has been operated for several months. After scalping a marketable garnet product from a minus 16 mesh dry crushed feed on a high intensity roll magnet the balance of the material is then roll crushed in a closed cycle until it will pass a 50 mesh screen. The product constitutes the feed of the wet magnetic separator. The heart of the new beneficiation process is a cyclically operated wet magnetic separator which exhibits the unique feature that unsized feed is easily handled. Product yields of higher purity are equal to that obtained with dry magnetic separations which use closely sized dry ore and multiple passes, but only produce wollastonite of about 98% mineral purity as determined by sink float techniques. It was anticipated that the wet processing through the grinding, milling and classification stage would yield a low cost 1µ ground product which should make available greatly increased applications for the mineral beyond those presently enjoyed. The improved purity was also expected to provide coarser sizes which might be utilized as a raw material for chemical modification which again would expand the uses of wollastonite. The evidence thus far collected appears to indicate that this premise may be expected to be fulfilled. There are on the surface of wollastonite particle sites at which cheinical reactions may occur1. It is believed that wet ground material provides a better base which will allow wollastonite a deeper entree into the field of chemical raw materials. Wet ground at 20µ and finer permits with certainty a number of chemical reactions, some of which are mentioned later in this article. While well crystallized wollastonite makes up the majority of the ore, the balance consists mainly of very weakly magnetic diopside of the hedenbergite-

Jan 1, 1965