Search Documents

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world's supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today's mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida's phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By J. S. Westwater

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W, within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleve-land-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. Al1en.† Mather " A " shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather "B," also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation. Shaft Sinking General Plan An average depth of 16 ft of sand overburden at the shaft site was cleared away by bulldozer, and the shaft approximately 15 by 20 ft in rock opening put down to an initial depth of 87 ft. Mucking of the broken rock to this depth was accomplished by an Insley excavator equipped with a 1/2 yard ca-pacity Owens clamshell bucket. Addition of 200 lb weight to each lip of the clam bucket provided adequate "bite" to dig the broken diorite and jasper rock. Temporary heavy wood bearers were placed across the shaft mouth to support the steel shaft sets which were hung in this initial 87 ft depth, aligned accurately and concreted in place from the lowest set upwards. The permanent steel headframe foundations and three service tunnel openings to the shaft were also concreted in the upper section to the shaft collar. A temporary wood headframe was then erected over the shaft mouth, and initial hoisting machinery assembled consisting of a Lake Shore 12 ft diam single drum grooved for a 1 3/8 in. rope and powered by two 400 hp motors to attain hoisting speed of 1100 fpm. Compressed air was obtained from a Nordberg 2 stage tandem horizontal type with a capacity of 1500 cfm. An enclosed landing platform at the shaft collar was equipped with a rotary dump and pocket for discharge of the rock into a Euclid 15 ton truck. On completing assembly of this equipment and installation of a special cage in the shaft, sinking was resumed on a three shift, six days per week

Jan 1, 1950

By P. Albert Carpenter, Wallace B. Howe, Michael N. Greeley, E. C. Bingler, Gilbert R. Eakins, Christy Bell, John Callahan, Gary B. Glass, T. J. Crabs

Although gold's market price dropped considerably from 1980's all time high, exploration for the precious metal remained a particularly bright spot last year, especially in the western US. For example, in Nevada-the nation's largest gold producer-further exploratory drilling at Louisiana Land & Explorations Co.'s deposit at Round Mountain and Newmont Mining Corp.'s find near Carlin resulted in sharp boosts in estimated reserves at both sites. Louisiana Land said its deposit is well on the way to being one of the largest gold reserves in the US. Based on further drilling, Newmont said its Gold Quarry property near Carlin could now produce 4.7-6.2 t/a (150,000-200,000 oz/ year). Reserves at Newmont's two properties near Carlin and a third property in southeast California are reportedly at least 218 t (7 million oz), up from the previously announced 128 t (4.1 million oz). Gold exploration activities were brisk in many other states, including a noticeable effort to explore and reopen dormant properties. Although the return on investments didn't appear as favorable last year as they did in 1980, the gold price was apparently sufficient to spur healthy exploration activity. Outside precious metals, market conditions, and subsequent exploration activity, appeared much more bleak. In the molybdenum market, for example, prices continued to slide, and Amax Inc. tightened its exploration budget. (Amax supplies 60% of the domestic market and 45% of the world demand for molybdenum.) The company spent 16% less on exploration during the first six months in 1981, compared to the same period in 1980. Copper and many other base metal producers appeared in similar straits throughout the year. Uranium exploration activities continued to suffer last year also due to depressed market conditions. Among others, Gulf Minerals Resources and Amoco Minerals Co. suspended uranium exploration activities in the West. Despite current unfavorable conditions, some companies continue uranium searches, confident that market conditions will rebound. On a brighter note, interest in exploring for some industrial and strategic minerals appeared on the upswing last year. Minerals used for oil and gas drilling, such as barite and special sands, were especially noteworthy. In geophysical activity, significant developments were achieved for electromagnetic techniques in both frequency-domain and time-domain systems. Geophysical logging activity declined due to decreased uranium exploration, and computer hardware continued to impact the way mining geophysical data are being acquired. Many presentations and papers were given last year to help exploration geochemists develop new techniques to locate concealed ore bodies. Among techniques described were statistical and computer modeling for enhancing anomalies over blind deposits.

Jan 5, 1982

By I. L. Dillamore

A purely geomentrical analysis based on oriented-growth relationships is presented to derive annealing-texture orientations in bcc metals from their- known deformation textures. The analysis takes as its starting point a description of- the bcc deformation texture and follows previous work on fcc metals in considering pvobable nurleation sites for recrystallization and the textural limitations on grains growing into a deformed matrix. The analy-sis accounts for the prominent and the minor coinponents of the annealing textures formed from two the deformation textures and can account for the ob-sem:ed temperature dependence of the annealing texture of bcc metals. THERE have been a number of investigations of annealing textures in bcc metals but few attempts to relate these textures to the deformation textures. This has been largely due to the lack of definition of both annealing and deformation textures, neither of which shows sharply defined orientations. It is, however, necessary to get a better understanding of primary recrystallization textures in bcc metals in view of increasingly exacting demands upon the quality of steel sheet for drawing purposes and as a necessary step towards the control of textures through processing. An analysis is presented here which relates annealing textures to deformation texture, by a purely geometrical method. This takes as its basis the oriented-growth theory of recrystallization and makes some reasonable assumptions regarding the make-up of bcc deformation textures and the limitations on growth relationships in bcc metals. Detailed information on this latter point is not available at the present time, and the present analysis may need to be streamlined or extended when such information is at hand. It is felt, however, that despite these limitations the analysis provides useful results and a valuable aid towards understanding the effect of processing variables. 1) BCC ROLLING TEXTURES Different workers have used a variety of descriptions for the texture developed in bcc metals by rolling. For the present purpose it will be assumed that two different deformation textures can be obtained: 1) a texture containing a major (112)[li0] component and a minor (001)[1i0] component for which increasing deformation causes the (001)[li0] component to increase at the expense of the (112)[li0] component, as suggested by Dillamore and ~oberts' (this is the texture predicted to arise starting from randomly oriented material); 2) a t~xture containing the above components and (111)[110] and (ii1)[112] components. This texture could arise from a material with an initial (110)[001] or (iil)[112] texture. It is well-known that the (ll0)[001] orientation rotates to (ii1)[112]that on roll-

Jan 1, 1965

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Songlin Ye, Frank Su

"Recycling valuable metals from waste streams has become increasingly important to the mining and smelting industry in China due to resource depletion and environmental concerns. Predicated on multiple large scale metal recovery operations designed by BQE Water at active mines in the Jiangxi Province of China, this paper presents a case study demonstrating recovery of zinc and copper from the waste stream at a major gold smelter in the Shandong Province of China. One of the issues facing the smelter is the lack of a cost-effective and robust process to recover zinc from the acidic process waste stream. As such, significant amounts of zinc-containing wastewater are neutralized with lime, resulting in not only the loss of zinc metal but also the generation of large volumes of sludge. In the case study, a sulphide precipitation process is chosen to selectively recover zinc and copper from the wastewater, in the form of commercial grade metal concentrates that can be sold as regular concentrates at the going market price. In the current project phase, over 2,500 tonnes of zinc metal and 40 tonnes of copper metal can be recovered on an annual basis. This not only generates revenue to offset waste treatment costs, but also eliminates significant amounts of sludge that would otherwise require storing and further disposal if the metals are not recovered.Introduction / Background With resource depletion becoming a global concern and environmental regulations becoming increasingly strict, companies in the mining and smelting industry are actively seeking technologies to maximize resource recovery and provide concurrent minimization of waste residue production from operational activities. Mining and smelting companies have typically used lime neutralization as the primary method to reduce metal concentrations from mine waters prior to reuse or discharge to the environment. However, this process creates large volumes of metal laden sludge with long-term liabilities in the form of ongoing storage and management (Zinck et al 1997). Recovering metals of value from mine water not only reduces sludge volumes and the costs of associated liabilities, it produces a commercial grade metal concentrate that can be sold to generate revenues to offset treatment costs. ChemSulphide® is a sulphide precipitation process developed by BQE Water that has been successfully applied at mine sites in the Jiangxi Province of China to remove and recover copper from acid mine drainage. The success of these copper recovery water treatment plants demonstrates both the economic and environmental benefits of recovering residual metals from mine water and provides reference for the copper and zinc recovery project at a gold smelter in the Shandong Province that is the subject of this case study."

Jan 1, 2017

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Albert E. Wood, Edgar R Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By J Cook, S Pike, D Pridmore

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The application of high-resolution seismic reflection to map structure and/or mineralisation in hard rock environments has progressed significantly in the last decade. Improvements in equipment, field practice, processing and understanding has seen the seismic reflection technique emerge as a cost-effective tool for high-resolution three-dimensional structural and lithology mapping to depths far greater and with superior accuracy than other more conventional geophysical techniques.This paper outlines results and preliminary interpretation of 2D and 3D seismic reflection surveys aimed at defining fault zones and locations for quartz load development in favourable host lithologies at the Cracow low-sulfidation epithermal gold system in Queensland, Australia.As this is possibly the first time that high-resolution seismic reflection data has been used to define the structurally-controlled location of low-sulfidation epithermal gold mineralisation, an important aspect of this work was the derisking or due diligence steps taken prior to commissioning the full 3D surveys at each site. This included full wave sonic logging, vertical seismic profiling and trial 2D lines. Interpretation of the 2D profiles and the drilling of interpreted structure provided the confidence to proceed with the full 3D survey.The advantage of collecting 3D data extends beyond ensuring that the received reflections are located correctly in 3D space. The final 3D data cube can potentially map the entire fault network, thus highlighting flexures and changes in orientation of the structures both vertically and along strike, which is an important aspect in the deposition of gold and for direct targeting.CITATION:Smith, R, Cook, J, Pike, S and Pridmore, D, 2015. Application of high-resolution seismic reflection surveys to exploration for blind vein systems at the Cracow low-sulfidation epithermal field, in Proceedings PACRIM 2015 Congress, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Albert E. Wood, Edgar R. Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as ''308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

The first Mine Rescue Performance Evaluation for mine rescue teams was held just prior to the 1992 RMCMI convention meeting schedule on June 27 and 28. Six teams took part in this year's evaluation; Decker Coal, Decker, Montana; BHP Minerals' White Team and BHP Minerals' Purple Team, both of Aztec, New Mexico; Kerr McGee Coal Corporation, Jacob's Ranch Mine, Gillette, Wyoming; The Coteau Properties Company, Freedom Mine, Beulah, North Dakota and The Falkirk Mining Company, Falkirk Mine, Underwood, North Dakota. This was the first mine rescue evaluation program developed to measure a unit's proficiency in their skills rather than emphasis on a ranking order of teams. The objectives for the evaluation were to promote learning and to evaluate the current level of experience of the attending rescue units. The priority goal for this evaluation was to recognize current rescue skills, knowledge and abilities of each team participating. In doing this, each team is provided with individual evaluations and a path for improvement as needed. [ ] Realistic industrial related scenarios, closely simulating the stress of actual rescue incidents, was provided by members of the Hermosa Cliffs Colorado Fire Department under the direction of Dan Noonan, Fire Chief. On Saturday, June 27, five rescue scenarios were presented for each team to complete and on Sunday three of a more difficult nature were encountered by each team. On the final day of the RMCMI convention two of the teams performed rescue demonstra¬tions. Onlookers were afforded the opportunity to view the teams in action as they simulated actual rescue operations. The value and importance of mine rescue teams such as those participating in this year's Rescue Team Performance Evaluation are very evident as in many cases they are the only rescue personnel and medical staff on the work site in case of an emergency. Most of these persons are volunteers who spend many hours studying, practicing and perfecting their expertise in the lifesaving techniques needed in the event of a mine emergency. At the same time, they are very qualified coal miners who perform their respective duties at their mine locations, Their dedication to gaining the most knowledge they can get to handle these life and death situations is evident in their participation in evaluations such as this one. [ ] If a highly educational, informative, sharing of knowledge and expertise, while at the same time providing a very enjoyable experience, deems this evaluation a success ... the Rescue Team Performance Evaluation held during the RMCMI Convention at Tamarron this year was certainly a SUCCESS!! It is hoped that you can all enjoy this same experience with us next year! Linda G. Ash The Falkirk Mining Company [ ]

Jan 1, 1992

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982

The use of scrapers in mining and earthmoving operations is not new; in fact they are one of the earliest methods of bulk earthmoving. A single machine, which can load, haul, and dump material with a minimum of ancillary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. Maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancillary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By Kim W. Wright

Introduction Mining operations require maps for each phase of project development. Engineering plans, cross-sections, and isometric drawings are also needed. Maps are used for geologic interpretation, reserve estimation, permitting, property acquisition, site studies, development work, and production. Maps and drawings are essential to mining. They provide needed information. Generating these products, however, requires many manhours. The filing and organization of maps and drawings is cumbersome, due to their size. Major map changes can necessitate the production of entirely new documents and, thus, additional manhours. The volume of maps and drawings generated in the life of a single project can be extensive. For example, some utility companies have data bases containing more than a million individual maps (one reported eight million). These problems were considered necessary evils in the past. Now, with the automation of map and drawing production, improvements can be realized. Computer-aided mapping and design offers a new approach for the production, management, and storage of drawings and maps. This approach promises benefits in time management, productivity, efficiency, and flexibility. In all economic projects, the bottom line is cost reduction. And implementing computer-based mapping and design techniques can lower costs and increase project profitability. AM/FM/CAD/CAM Automated Mapping/Facility Management (AM/FM) and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) are becoming buzz words in the engineering world. Most relevant to mining are the concepts of AM and CAD. These terms relate to the application of computers, specifically computer graphic technology, to mapping and design. CAD refers primarily to the design of components and structures in two and three dimensions. But it can apply to the three dimensional modeling of mine workings, ore bodies, and geologic structures AM refers to the automation of conventional map production. AM/CAD systems use computers to store, manipulate, produce, and update drawings and maps in two and three dimensions. Ideally, the calculating capabilities of computers are also used in conjunction with design and drawing generation, offering capabilities not available with conventional, manual mapping and design processes. To better understand concepts associated with AM and CAD applications, the understanding of a few computer-related terms is necessary. Table 1 explains some of these terms. System Features The capabilities of AM/CAD systems are based on viewing transformations. These are the basic, manipulative tools by which AM/CAD packages generate visual representations of data. Examples include the rotation of a three-dimensional object through space, the expansion or contraction of maps to fit a given scale, enlargements of small areas on maps or drawings for detailed viewing, and the generation of cross-sections from three dimensional data. AM/CAD systems incorporate data base management in their architecture. This allows a user to modify, move, delete, or manipu-

Jan 6, 1985