Search Documents

By J. Jordan, D. K. Denton, D. Tesarik, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health integrated the results of studies from a seismic tomographic survey, a finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. The key findings were that (1) the seismic tomograms showed that seismic velocities in rock adjacent to mine openings were low, (2) a difference tomogram in which in situ stresses on the east and west sides of the slot were compared showed that velocities increased west of the slot but decreased east of the slot, (3) geologic features (rock types and a fault) identified through geologic mapping were recognizable in the seismic tomograms, (4) ultrasonic velocity measurements on the rock cores agreed with seismic velocity measurements in the tomograms, and (5) results from a finite-difference analysis compared well to the seismic tomograms west of the slot but not east of the slot. The significance of this research is that seismic tomography is a useful tool for determining relative stress in underground pillars.

Jan 1, 2004

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995

The Ocean Drilling Program is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (Legs) which each last approximately two months. These legs are designed by geoscientists from the 19 countries that subscribe to ODP. Australia and Canada share ODP membership under the banner of the AUSCAN Consortium. The Australian Secretariat of the ODP is housed at the Department of Earth Sciences at James Cook University, along with the AUSCAN Consortium office. The Canadian Secretariat is presently based at the University of Toronto. Both secretariats have major research interests in the ore deposits, both ancient and modem, and so there is currently a major drive by the AUSCAN ODP Consortium to make available data and technological information to the minerals industry. This type of information includes data from drilling hydrothermal sites such as the hydrothermally active TAG black smoker complex on the Mid-Atlantic Ridge, drilled during Leg 158, and the Middle Valley sulphide deposit, on the northern Juan de Fuca Ridge, which was drilled during Leg 139.

Jan 1, 1996

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

Analysis of different environmental scenarios and to represent, spatially, of impacted areas is possible by the use of geoprocessing techniques, specifically Systems of Geographical Information (SIG). Through these systems it is possible to create dynamic mathematical models, constituting of a georeferenced digital database and employing the integrated data originated from several sources. In this context, the general goal of this paper is to apply this tool in an environmental analysis of a specific karstic area impacted by mining activities. In order to preserve a limestone site, internationally recognised by its archaeological features, including caverns, lakes and evidences of prehistoric ages, the Brazilian government has created the Lagoa Santa Environment Protection Area. This place is located in the proximity of the Belo Horizonte international airport. In the past two decades exploitations of dimension stones have increased in this area. These exploitations have been done without a mine plan promoting several environmental impacts. The objective of this paper is to analyse these activities using SIG as a basic tool to locate the main mining related impacts and propose mitigation measures including waste and tailings disposal and reshaping of the landscape and introducing a drainage system for the considered zone.

Dec 6, 2010

By Patrick Ph. D. Kennedy, Osvaldo A. Ph. D. Bascur

With the revolutionary progress in information and computer technologies, applying the latest information technologies in metallurgical complexes has become a serious challenge to both a major opportunity and a serious challenge to both management and technical teams. The emerging component and object technologies are changing the way everyone can beneficially use their computer and networks to add to their corporate bottom lines. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All process equipment and control strategies require maintenance from local personnel at the mine. Integrated use of existing and emerging technologies is making it possible to implement an overall process effectiveness control index. This index is based on key indices such as losses due to plant availability, performance efficiency and rate of quality. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is highlighted. An emerging plant integration paradigm is described to simplify the implementation of business enterprise resources management and distributed plant management systems.

Jan 1, 1998

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

With mining development on hold and other underground works in a slowdown, the development of nuclear wa te repositories takes centre tage on the American rock engineering scene. Three repositorie for commercial spent fuel-in salt, tuff, and basalt-are in the phase of site characterisation and conceptual design, and one pilot project for defense high-level wa te in salt is under construction. A repository design for crystal line rock has recently been postponed.Because of strict quality assurance requirements throughout design and construction, and because of the need to predict and ascertain in advance the satisfactory performance of the underground openings, much intellectual energy has been expended to analyse underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behaviour and improved methods of underground analysis and design. For the shorter term, a formalised ground control plan was developed, the principles of which may be applied to other types of projects.This paper summarises the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1988

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By Gregory J. Chekan

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating multiple seam interactions associated with longwall mining. Longwall gate entry and panel stability have been influenced by previous mining in coalbeds above and below a mine in Virginia that operates in the Lower Banner Coalbed. Directly superjacent, approximately 115 ft, the Upper Banner Coalbed has been partially worked by room-and-pillar mining. Directly subjacent, approximately 730 ft, the Tiller Coalbed has been worked by partial room-and-pillar retreat mining. The study mine has experienced problems during development of gate entries in areas of overmining and undermining. It is anticipated that stress fields associated with adjacent mining may further affect gate entry stability and face advancement during the extraction of the longwall panel. To assess overmining and undermining effects on ground stability, the Bureau gathered geotechnical information at the site. Headgate entries and pillars were instrumented and monitored to study loading behavior as the longwall face approached and passed potential problem areas. Measurements indicate that although increases in average pillar pressure were greater than predicted values, previous mining in adjacent coalbeds had little effect on headgate stability.

Jan 1, 1989

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

With mining development on hold and other underground works in a slowdown, the develop- ment of nuclear waste repositories takes center stage on the American rock engineering scene. Three repositories for commercial spent fuel -- in salt, tuff, and basalt -- are in the phase of site characterization and conceptual design, and one pilot project for defense high-level waste in salt is under construction. A repository design for crystal line rock has recently been postponed. Because of strict quality assurance requirements throughout design and construc- tion, and because of the need to predict and ascertain in advance the satisfactory perfor- mance of the underground openings, much intellectual energy has been expended to analyze underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. For the shorter term, a formalized ground control plan was developed, the princi- ples of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1987

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By West RF, Pooley RH

An underground mine, a treatment plant and supporting facilities have been constructed at Lebong Tandai in Sumatra, Indonesia by PT Lusang Mining. Throughput is initially 50,000 tonnes per annum of ore with an inbuilt capability to expand to 100,000 tonnes per annum. Construction proceeded in parallel with design work on a tightly controlled critical path schedule. The very remote location of the mine, the difficult access and the fact that equipment was imported from many parts of the world presented a challenging project management problem. The transport system, which involves road, river and rail and support facilities on site had to be brought into full operation prior to the arrival of major equipment. Mine development involved the reopening of the old access drives and workings, refurbishing two shafts and the haulage system together with redevelopment of old stoping areas and the opening of new stoping areas. Ore production is now from three main areas using shrink and underhand stoping methods. Ore breaking and drive development is with conventional airleg mounted rockdrills and ANFO explosives. Exploration to locate and develop new reserves to replace ore mined is an ongoing activity.

Jan 1, 1986

A biological column leach testwork program was undertaken on a chalcocite ore. Three tests were conducted in all, using 65 in x 100 mm columns in three sections. The tests were started with varying acid strengths and inoculated with bacterial solutions from previous column testwork. The leaching of Cu was found to occur in three stages. These stages consisted of direct acid leaching, bacterial oxidation and ferric iron leaching. These leaching stages can most easily he described through the examination of not only Cu dissolution but also Fe dissolution and its subsequent oxidation and precipitation. The p11 of the system was found to he critical in establishing and maintaining the bacterial leaching system. The oxidation potential was seen to he influenced by the leaching system as the oxidation states altered. Test variables such as, 02, COz, and temperature were all found to influence the system. Final copper recoveries were in excess of 90 per cent in each column test over a leach time ranging from 211 to 328 days. Given similar leach conditions are applied, the application of this technology to site is expected to give comparable results.

Jan 1, 1994

By Kevin Connor

The Government's ban on all commercial mining operations, except for small-scale artisan exploitation of alluvial gold deposits, continued throughout 1985. Minerals produced were kaolin and lime for agricultural uses, and experimental peat harvesting for energy applications. The total value of the minerals produced during the year was estimated at $1.1 million .2 In early 1985, an agreement between the Government and Amoco International Oil Co. was ratified for a petroleum exploration concession covering 248,000 hectares of Lake Tanganyika. Onshore exploration in the Ruzizi Plain was already under way the last half of 1985. By yearend, enough seismic information was available that Amoco hoped to complete data analyses, determine onshore drilling sites, and begin drilling operations before the end of 1986. Also to begin in the latter part of 1986 were seismic studies of Lake Tanganyika. Throughout 1985, Amoco officials were negotiating with the Government of Zaire for expanding the exploration acreage into that country's portion of northern Lake Tanganyika and the Ruzizi Plain. An agreement between Amoco and Zaire could have important beneficial economic implications for both Zaire and Burundi, and onshore seismic work in Zaire logistically supported from Bujumburi could begin almost immediately.

Jan 1, 1987