Search Documents

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

By F. Chen, L. J. Gaydos, D. C. Kuhn, Demersm L. M., S. C. Sun

"Summary: In this report the differential regulation of NF-KB and nitric oxide (NO) was investigated in the mouse macrophage cell line RAW 264.7 following exposure to a mineral dust (silica) and /or an endotoxin (Lipopolysaccharide, LPS). The results indicated that silica and LPS can significantly induce the activation of NF-KB as well as elicit enhanced production of NO in RAW 264.7 cells as part of an early inflammatory response mechanism. A 24-hour time-course study showed that NO release from these cells continued to increase following the initial stimulus by LPS or silica. In contrast, activation of NF-KB was maximal at 6 hours and then showed a steady decline to 24 hours. The production of NO was suppressed by protease inhibitor and antioxidant, both of which block the activation of NF-KB. Surprisingly, the use of an NO synthase inhibitor resulted in an enhancement of NF-JCB activation. These findings suggest that NO produced in macrophage cells in response to an inflammatory stimulus like silica or LPS my be linked to a negative feedback role on the activation of NF-KB. It is now accepted that nitric oxide (NO) plays a pivotal role in the inflammation response process when macrophage cells are activated by a pro-inflammatory stimulus (l). Production of NO is dependent on the activity of the enzyme nitric oxide synthase (NOS). Up until now, at least three distinct genes have been described which encode different isoforms of NOS. NOS has been cloned from a variety of different mammalian cells, including constitutive neuron NOS, constitutive endothelium NOS and inducible NOS (2). Macrophages appear to be the principal cellular source for the inducible form of NOS (iNOS) activated in response to an inflammatory producing event. The mechanisms subserving the regulation of the iNOS gene and NO production have been under intense investigation in recent years (3-5). Several binding sites for transcriptional factors have been identified in the promoter region of iNOS gene, including NF-lCB, AP-1, NF-IL6, Oct-I to cite a few (5). NF-KB appears to play a"

Dec 1, 1996

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in intensified efforts in inspections of coal refuse sites by the Mining. Enforcement, and Safety Administration (MESA). MESA inspections however, are mainly qualitative and are often time consuming, Therefore, in August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in MESA inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photo interpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Based on CH2M HILL results cost for monitoring by rapid system was approximately 25 percent of cost by conventional ground survey.

Jan 1, 1980

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By Robert P. Vinson, Kissell. Fred N., Edward D. Thimons

"The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.INTRODUCTIONAny location in a coal mine where 5 pct or more of methane is present constitutes a potential site for an explosion and roof cavities are likely locations. Unfortunately, little is known about the buildup of methane in roof cavities. Some research has been done using scale models where no air flows past the cavity so that methane disperses only by diffusion (5) 4 a rare situation in mines.No known cavity-model investigations have been made that simulate air and methane flow conditions normally encountered underground. These Bureau of Mines studies were undertaken to determine the extent and manner of methane buildups in coal mine roof cavities with air velocities in the range normally found in coal mines and with various methane emission rates."

Jan 1, 1978

U.S. demand for building and construction materials, such as construction aggregate, gypsum, and cement, remained strong in 1989. Cement imports declined slightly, representing about 17% of apparent consumption compared with 19% in 1988. Mexico, supplying 29% of the total, was the primary source of imports, followed by Canada with 21 %, Japan with 14%, and Spain and Greece with 10% each. Mexico was also the target of an antidumping petition, filed by producers in Arizona, Florida, New Mexico, and Texas, alleging that Mexican cement was being sold in these areas at less than fair value. This was the second petition filed against Mexico in the last 3 years. The International Trade Commission made a preliminary determination that the cement industry in these regions was materially injured by Mexican imports. U.S. demand improved for construction aggregate for the fourth consecutive year and was at a near-record level. The U.S. gypsum industry performed well, even though new housing starts decreased for the third consecutive year. Increased U.S. exports of gypsum wallboard and strength in the remodeling markets offset the impact of declining housing starts.

Jan 1, 1990

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By R. C. Gilmore, J. McMack, G. E. Bogin, J. F. Brune, C. DeRosa

"Researchers at the Colorado School of Mines are designing and building a 1:40 scaled physical model of a fully operational longwall coal mine. The purpose of the model is to minimize the occurrence of methane explosion hazards by testing various ventilation strategies and determining optimal methane sensor placement throughout the longwall face. Fluid scaling factors were analyzed using Computational Fluid Dynamics software Ansys FLUENT™ at both full and 1/40th scales. Researchers were able to identify key scaling factors and subsequently developed suitable flow parameters that would maintain full scale accuracy of flow patterns in the 1/40th model. KEYWORDS Coal, Longwall, Methane, Explosion, Scale Model, Ventilation, Fluid Dynamics, Richardson, Gob, Porous INTRODUCTION Mine ventilation systems are a key component for ensuring a safe working environment by introducing fresh air from the surface and diluting explosive gases and hazardous contaminants. This holds true for longwall coal mines where the emission of flammable methane gas from the longwall face as well as the gob can create explosive mixtures of methane and air. Therefore, an effective ventilation strategy can help mitigate the potential for accidents within a mine. Developing an effective mine ventilation system (MVS) requires a detailed understanding of the physics of gas transport and how this relates to specific geometries and obstructions in the face. Researching this phenomenon requires the development of computational fluid dynamics models capable of simulating fluid flow and methane species transport that can be validated through physical experimentation. Unique site conditions determine ventilation layouts for every coal mine. Researchers have designed a 1/40th scaled physical model of a longwall coal face and adjacent gob that includes movable shield supports and a movable shearer with rotating cutter drums that can be adjusted to a variety of ventilation conditions. The proposed work will address the need for an improved Mine-wide Atmospheric Monitoring System (AMS), and provide the ability to link existing MVS models with AMS in real time. By accurately representing the coal face, the gob area and the mining equipment, gate roads and bleeder entries, the scaled model accurately represents all relevant structures, geometry, and dynamic conditions. A Plexiglas cover allows full optical access for sensor equipment as well as visual inspection of the fluid flow and species transport."

Jan 1, 2019

By Hazel J. Stratton

IN THE HALF-CENTURY that has passed since the Bureau of Mines was established in July 1910, the research and technologic investigations conducted by the Bureau's scientists, engineers, and other personnel have helped significantly in improving health and safety in the mineral industries and have contributed substantially in conserving the Nation's mineral resources through improved techniques in the mining, treatment, and use of mineral commodities. From Bureau laboratories have come new materials for industry and better methods of extracting and processing minerals and mineral fuels. Bureau safety investigations-complemented by equipment testing and by programs of mine inspection and education-have brought about safer and more healthful working conditions.

Jan 1, 1960

By G. Récoché, A. Chamaret, M. O’Connor

Building indicators that respond to all stakeholders' needs is a time-consuming and complex exercise, with certain questions still unsolved. The aim of the current three-year research project, carried out in partnership between BRGM’s Mineral Resources Division and C3ED, is to propose a top-down / bottom-up indicators building methodology that combines conception and coordination methods and a participative approach. The tool-design phase is based partly on a comparative analysis of existing international initiatives according to different criteria (objective, observation scale, framework, etc.). The study of two African mining projects will provide the opportunity to confront the conceptual aspects with reality in the field. Careful consideration of the participants’ suggestions will result in a set of indicators that can be easily understood and adopted by all stakeholders. The final objective is to measure the impact of a mining site on a local, regional and national sustainable development frame, throughout the full life cycle of a mine.

Jan 1, 2005

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By D. Goffaux

In less than two years, Stratmin has discovered, explored, developed, financed and put into production by open pit, a large graphite mine. The deposit, hinted by airborne electromagnetic survey, was discovered in September 1987 through various ground geophysical surveys, diamond drilling and trenching. The open pit started production in February 1989, feeding a nearby leased mill at Notre-Dame-du-Laus (Quebec), having a processing capacity of 400 tons per day. A new 1,000 tonne per day mill was built at the mine site, in Lac-des-lies (Quebec) and began production in April 1990. The Lac-des-lies graphite operation is currently one of the largest of its kind in the world. Mine and mill facilities are operated by Stratmin Graphite, jointly owned by Stratmin Inc. (75%) and Imetal-France (25%), a wholly owned subsidiary of Imetal (France). From initial exports limited to Japan and United States, Stratmin Graphite is now exporting in fourteen different countries, attesting to the very high quality of its products, with grades ranging from 92% to 97% carbon. Among the numerous graphite deposits discovered in Canada, Stratmin Graphite Inc. has emerged as the leader and virtually the sole crystalline graphite producer in North America, operating on a continuous basis.

Jan 1, 1992

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By Milton E. Wadsworth

The evolution of engineering education and research has been profoundly influenced by computer technology and has concomitantly followed changes in this technology. Today, virtually all faculty have access to at least two hierarchies of computers: desk personal computers and at least one echelon higher (workstations or a variety of mid-sized computers). Most faculty have access to three or even four hierarchies: the two listed, plus super-mini and super computers. The ready availability of computers at a low cost has increased dedicated and site-specific computer technology. This has permitted universities to move into the field of macro-engineering, to address increasingly complex problems in resource recovery, manufacturing and many other areas, including important societal problems, like the environment. The creation of university research centers indicates the growing importance of macro-engineering involving large systems of interactive components. Funding agencies have increasingly favored such centers since they cross disciplines, generate inter-university consortia and foster university-industry programs.

Jan 1, 1992

By R. A. Mantz, V. N. Balbyshev, A. N. Khramov, N. N. Voevodin

Corrosion protection properties of the hybrid organo-silicate coatings on aluminum substrate can be significantly improved by means of encapsulation of organic corrosion inhibitors within the coating material. In order to achieve sustained release of corrosion inhibitor and long-term corrosion protection, a secondary chemical equilibrium of either ion-exchange interaction with the coating matrix or cyclodextrin-assisted molecular encapsulation of the inhibitor has been employed. Several organic corrosion inhibitors, such as mercaptobenzothiazole, mercaptobenzimidazole, mercaptobenzimi¬dazolesulfonate, and thiosalicylic acid have been examined by a group of electrochemical methods including potentiodynamic scan, electrochemical impedance spectroscopy, and scanning vibrating electrode technique. It has been found that the formulations that contain ß-cyclodextrin demonstrate superior corrosion protection capabilities as the complexation equilibrium results in a continuing delivery of inhibitor to corrosion sites. The approach is considered a promising way for active corrosion protection of high-strength aluminum alloys when integrity of barrier coating is compromised.

Jan 1, 2004

By David A. Collins

Red Dome Gold Mine classifies ore types within the pit by gold and copper grades. Copper grades are further distinguished by total copper and cyanide soluble copper levels. At present, Cyanide Soluble Copper samples take six hours of agitating before they can be assayed. This agitation time produces results which are a proportion of the total cyanide amenable copper. This relates to our plant's performance. Frequently the total copper result is needed before we can begin the cyanide soluble copper analysis. This caused a protracted tum around time. Mennetech Pty. Ltd has produced a catalyst proven by David Martin Menne to accelerate the cyanidation of gold. David said that the information at hand indicated that Leach WELL TM also accelerates the leaching of cyanidable copper substantially. Test work was undertaken on-site at Red Dome Gold Mine to investigate the potential of Leach WELL TM to reduce the leaching period and therefore, the overall tum around time required for cyanide soluble copper determinations.

Jan 1, 1995

By P. Whincup, T. Showell, B. Marchant, R. Dunne

An oversupply of copper on world markets in the early 90' s, coupled with a decrease in demand, resulted in a "tight" market for the sale of copper concentrate. In these conditions small producers of low grade copper concentrates found it difficult to sell their products. The situation was exacerbated for those producers also having reasonable quantities of penalty elements (e.g. As, Bi). The Telfer Gold Mine bulk copper gold concentrate, produced from treating underground sulphide ore, fell into this category (i.e. 16% to 20% copper, 30% to 35% sulphur and 3500ppm to 4500ppm arsenic). The concentrate sulphide minerals are predominately chalcocite and pyrite. Although a higher grade copper concentrate was attainable a substantial decrease in gold recovery ensued. Under the prevailing market conditions a decision was made to stockpile concentrates pending either an easing of market conditions or alternatively finding an on site method for treating the concentrate to recover both the contained gold and copper.

Jan 1, 1995