Search Documents

By Julian Malnic

Various natural, commercial, engineering and operational factors govern the evolution of approaches taken in the exploration for Seafloor Massive Sulphides (SMS) and in delineating the resource. These stages are prerequisites to the proposed mining of SMS deposits. This paper presents and analyses these factors from the view of an SMS exploration company that is pioneering the exploration of this rich alternative source of zinc, copper and gold. Current exploration practices developed by Marine Scientific Research (MSR) workers for SMS deposits are expected to give way to industry-generated methods as the SMS exploration industry gathers momentum. The exploration process falls into three phases that are described below: Prospecting (locating targets), Indicating Resources, and Measuring Mineral Resources Considerable streamlining of the SMS exploration process will accelerate the rate of discovery. The economics of SMS mining are projected to be superior to comparable terrestrial mining operations in both operating cash cost and capital terms.

Jan 1, 2001

By L. Petitnicolas

The experimental study of nitrogen absorption and its removal from a liquid Ni-20%Cr alloy at 1873 K has been undertaken, using an experimental, apparatus based on the Sieverts technique in order to determine the solubility of nitrogen in the alloy. as well as the kinetics of nitrogen transfer across the gas/melt interface. Experiments show that nitrogen solute equilibrium content can be calculated using the Sievens law. Measurements point out the nitrogen absorption reaction rate to be well described by first order kinetics, whereas experiments on nitrogen removal reveal that the rate is better expressed using a second order equation.

Jan 1, 1996

By S. Garcia

The Minera Yanacocha operation presents various operating challenges, due to the complex structure of several heaps interconnected with ponds and gold recovery plants. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters on issues such as water usage and inventory. An integral component of the water/mass balance of the process is a model of each heap that describes the flow and chemical behavior based on the individual characteristics of the heap. A computational fluid dynamic (CFD) software framework is used to model the individual heaps. The structure, calibration and validation of the model are described. Several examples demonstrating application of the process heap model are presented for the La Quinua heap. The effects of loss of solution flow to the heap (i.e., pump failure), increased cyanide levels in applied solutions and higher copper head grades on the process operation and balance are investigated with model simulations and compared to the baseline operating conditions. An example of estimating gold production and inventory based on projected heap loading plans is provided.

Jan 1, 2010

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-million-standard-cubic-foot-per-day, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 million tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the terms of the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment varies: $65,137,900 for the 4.8-million-ton-per-year (MM tpy) mine in the Eastern province, $78,514,600 for the 6.72-MM-tpy mine in the Interior province, and $42,050,100 for the 9.2-MM-tpy mine in the Northern Great Plains province. Total capital investments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $86,969,900, $109,378,500, and $78,543,500, respectively. Corresponding selling prices for the coal, per ton, are $6.94, $6.03, and $3.39, assuming a 15-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1976

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By M Sandy, A Vakili, J Albrecht

Although rock strength anisotropy is a well-known phenomenon in rock mechanics, its impact on geotechnical design is often ignored. No widely accepted guideline currently exists for its characterisation. Anisotropy can significantly control the failure mechanism and progression of damage into the rock mass, particularly in high-stress conditions. As such, it can play a key role in the stability of underground excavations and subsequent geotechnical design.This paper introduces the concept of anisotropy at both intact and rock mass scales. It then presents guidelines for measuring anisotropy and assigning rock mass strength properties. An improved unified constitutive model (IUCM), which can account for more complex failure mechanisms, is then briefly described. This IUCM is used to better understand the typical responses of anisotropic rocks to underground mining and to develop an improved damage classification scheme for these conditions.The application of conventional design methods in anisotropic conditions is shown to lead to significant errors. Two case histories are then presented, illustrating how the proposed methodology can improve the reliability and accuracy of the geotechnical analysis when compared with conventional design methods.CITATION:Vakili, A, Albrecht, J and Sandy, M, 2014. Rock strength anisotropy and its importance in underground geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 167–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By Hans von Michaelis

There has been a renaissance in gold and silver extraction and recovery that has taken place over the last fifteen years, since the price of gold was freed from the $3510~ level. Despite major advances in such areas as carbon adsorption processes for gold recovery, refractory gold ore treatment, crushing and grinding, process control, etc., there still remain several gold and silver mineral processing frontiers. Frontiers related to environmental management present significant challenges especially in the USA. More than ever it is appropriate to optimize total economics by adopting a "systems approach" that integrates mining, mineral processing and environmental management.

Jan 1, 1993

By M Korte, J McMaster, C Brent

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and has increased production from the original 119 t/h design capacity to a milling throughput of 265 t/h in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of underground and open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate. Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Process Technology and Innovation (PTI) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently with surveys of both the crushing/grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model, such that overall process optimisation was possible. This was to apply both by exploring the operating limits of the currently installed plant, as well as looking at the logical next stage of capital plant expansions. Surveys of the crushing and grinding circuits were conducted at the Osborne concentrator in May 2008. The main objective of the surveys was to review the potential of increasing grinding throughput whilst maintaining the flotation feed 80 per cent passing size. This would also require improving the efficiency of the crushing circuit which was already operating in excess of 80 per cent of the time. Steady-state simulations were performed using the developed circuit models to identify opportunities to increase throughput and alleviate high circulating loads in both the secondary crushing and grinding circuits. Due to operational changes, the recommendations resulting from this project were considered by Osborne but have as yet only been partially implemented.  This paper covers part A or the crushing and grinding component of the project. A separate paper discussing part B or flotation is also being presented at this conference. The results of interactive simulations between the flotation and grinding circuit models are included in part B of this paper.

Jan 1, 2009

By R. K. K. Mbaya

The concept of adsorption or separation of platinum anions from base metal cations in chloride media using native or chemically modified activated carbons has been discussed in various journals within the context of batchwise systems. In our research work, a fixed-bed column, loaded with native and amine-immobilized activated carbon pellets (Norit RO 0.8), was used to study selective adsorption of platinum ions from chloride media at different flow rates, bed depth and initial metal concentrations. The kinetics, mass transfer characteristics, breakthrough data and separation factors (ß(Pt/Fe) and ß(Pt/Cr)) were quantitatively analysed and modeled. The bed-depth service time (BDST) model was used to model the breakthrough curves successfully in fixed-bed columns and also the dispersive diffusion in the radial and axial directions of the bed were evaluated. The inner diameter of the column was 3 cm and the bed depth was between 1.0 cm and 2.5 cm. Concentrated 4 M HCl acid solution was used to elute the fixed-bed column. It was demonstrated that amine-treated activated carbons provides superior separation factors between platinum and base metals (Fe, Cr). Results showed also, that 95% saturation was reached within 10~26 hours depending on the nature of ACs at a flow rate of 11 mL/min and initial concentration of 5 ppm.

Jan 1, 2014

By Enrique Levy

The publication from which this paper was abstracted is the first at-tempt to correlate all the metallogenic deta compiled by the author for the preparation of the 1:2,000,000 Metallogenic Map of Central America. It is not a treaty of metallogenic theories but rather a careful effort to postulate metallogenic provinces and epochs with the intention to stimulate other geologists and mining companies familiar with the area to criticize and improve on the ideas proposed. The sole purpose being to find new mineral deposits for the betterment of our people.

Jan 1, 1971

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946