Search Documents

By M. J. Gula

In the solvent extraction -electrowinning recovery of copper from oxide or sulfide ores there is a continuous transfer of iron and other impurities from the primary leach solution to the copper electrowinning electrolyte via chemical transfer or mechanical entrainment. Iron is the principal impurity that has to be controlled in the electrolyte by a "bleeding" of the electrowinning solution. This bleeding transfers copper and sulfuric acid back to the primary leach circuit along with the iron. Copper is recovered via the solvent extraction process and generally the sulfuric acid is used as a reagent in leaching. Unfortunately, cobalt, which is added to the electrowinning solution to modify the anodic process, is irreversibly lost through the bleeding operation. This cobalt loss represents a significant operating cost to SX-EW copper producers. DiphonixTM ion exchange resin contains diphosphonic acid and sulfonic acid functional groups on a polystyrene-divinyl benzene matrix. This resin has been found to strongly and selectively extract ferric ion from copper sulfate -sulfuric acid solutions containing cobalt. Thus, an ion exchange process using DiphonixTM resin for the control of iron has been developed to replace the conventional bleed stream process. The new process minimizes the loss of cobalt from the electrowinning circuit and strips the iron into a sulfate based solution suitable for leach solution makeup. In addition, this process can effect a lowering of the total iron concentration in the electrolyte circuit with an associated increase in current efficiency. In this paper, data on the loading and elution of iron are presented. Laboratory and pilot scale data will be discussed along with information on process design and comparative economics.

Jan 1, 1996

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By S. Rukhaiyar, M. Ramulu, G. Pradeep, P. K. Singh, P. B. Choudhury

The drill and blast method is the most prominent rock excavation method used in mining and civil engineering projects. The ground vibration is the most undesirable effect of the blasting and needs to be controlled. The blasts are designed so that ground vibration at nearby structures must remain under the prescribed limit. Various empirical blast vibration attenuation models have been presented to estimate the ground vibration for designing purposes. These models assume ground vibration as a function of distance and maximum charge per delay. United States Bureau of Mines (USBM) model is most commonly used for the blast design. However, the uncertainty associated with these models is seldom characterized, thus diminishing its reliability. The probabilistic Bayesian approach associated with the Monte Carlo method can easily quantify uncertainties associated with the model and its parameters. Thirty-three blast vibration observation data from a granite quarry in Kerala, India, is used to estimate the probability distribution of model parameters. Markov Chain Monte Carlo (MCMC) approach is used for sampling 12,000 samples for obtaining the posterior distribution of parameters. The uncertainty associated with model parameters is quantified from the posterior distribution, and this is further used to estimate the credible and prediction limits of the model. The point estimate of the most optimum value of the parameter is estimated using maximum-aposteriori or MAP estimate. The model parameters are also obtained using the commonly used least-square error method, which is a maximum likelihood estimation or MLE approach. It has been observed that the accuracy of the model obtained using both MAP and MLE approach is almost equal. However, the MAP estimate as per Bayesian probabilistic analysis has the added advantage that it can estimate the uncertainty of parameters as well as the model, which is not possible using the MLE approach.

Sep 27, 2021

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011

By H Fletcher

Iron Ore Holdings Ltd (IOH) is an emerging junior iron ore company that is actively developing projects in the Central and Western Pilbara region of Western Australia. IOH commissioned URS Australia Pty Ltd (URS) in mid-2008 to prepare environmental assessment documents for the Phil’s Creek Project, which was rapidly moving into the development phase. This project comprised a small open cut iron ore mine that was expected to deliver approximately seven million tonnes over a five year mine life.IOH faced several challenges in the environmental assessment process for the Phil’s Creek Project. Although the Phil’s Creek Project attained approval but has now been placed on hold, it is a useful case study to discuss these challenges and how IOH addressed them. Several important lessons were learned through this process that can assist other proponents in addressing environmental challenges in a constructive and proactive manner.One major challenge faced by IOH related to the endangered northern quoll (Dasyurus hallucatus). Another challenge was the unusually high species richness of troglofauna recorded within the project area, with several species initially known only from within the proposed pit footprint.Meeting and overcoming these challenges has provided IOH with an increased understanding of the level of input required for consultation with government departments regarding environmental assessments, and this should stand the company in good stead for developing future tenements. Challenges in regards to the environmental assessment process may be faced during future developments, but IOH’s experiences to date and the lessons learned from the Phil’s Creek Project, will help pave the way for successfully overcoming them.

Jul 11, 2011

By Mike Dry, Rod Dry

If humanity is truly serious about reducing emissions of carbon dioxide into the atmosphere, today’s power plants burning fossil fuels will have to be replaced by power plants that do not emit CO₂. Unless carbon capture/sequestration becomes practical, the new power plants will be hydroelectric, wind, solar or nuclear installations. Hydroelectricity requires the appropriate geography. Solar installations can only deliver power as and when sunshine is available, and wind installations when the wind blows. Therefore, power from these sources will be intermittent, but the demand for electricity does not follow the patterns of sun and wind. That will require large-scale electricity storage and/or load following by the remaining power suppliers, increasingly so as the use of fossil fuelled power generation declines. Modern nuclear power plants are designed for demand following. However, operating at lower than design output has a negative impact on the economics of nuclear power plants because the overall cost of the electricity they generate is dominated by capital cost. Primary (blast furnace) iron smelting is responsible for a significant part of global CO₂ emissions because the reagent used is carbon. Were it available in sufficient quantity (and at a low enough cost), hydrogen could replace carbon in the manufacture of raw direct reduced iron (DRI), using technology such as modified HYL (Tenova Hyl, 2018) or Midrex (Ravenscroft, 2017). This paper examines a scenario in which, instead of demand following, nuclear power stations are operated at their design capacities and surplus power is used to generate hydrogen in off-peak periods. This hydrogen is then used to replace carbon in the manufacture of raw steel.

Jan 1, 2020

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Joseph G. Carleton

INTRODUCTION The increasing concern for the environment may well present far more opportunities than problems for those involved in all phases of tunneling. All too frequently in the past, environmentalists and their concerns have been cast in a negative light, as obstacles to be overcome. Often forgotten is the fact that these same environmental concerns have created a rapidly increasing demand for new tunnels. Tunnels for rapid transit projects, clean water supply, and sewage treatment have been given a boost because of environmentalists' concerns about overuse of automobiles, inadequate water supplies, and improper sewage disposal. Concurrent with increasing use of tunnels to help solve or alleviate some of our environmental problems is an obligation not to create new ones in the process. Concerns which we feel responsible tunnel owners, engineers, and contractors should address themselves to include: (1) Minimum energy consumption, both during construction and in operation of the completed project; (2) proper storage and/or disposal of the excavated material; (3) minimum disruption during the construction process - noise, traffic, unnecessarily unsightly work areas, and possible weakening of foundations of nearby structures; and (4) a finished project consistent with community and environmental goals. We are especially concerned about two things. First, the longrun implications of a project -- what's good for a few people in the short-run may be bad for most of the people in the long-run. Cutting corners to save a little money now is false economy. Second, the fact that ultimately we all share the same earth -- its water, air,

Jan 1, 1974

By Maral Malekian, Pat Bellett, Eranda Tennakoon, Fernanda Carrea, Moe Momayez

Slope instabilities in open-pit mines pose a safety risk to workers and a financial burden on production. The direct impact of slope stability on safety and production makes slope failure predictions one of the important challenges in the mining industry. Predicting the precise time of slope failure has been the subject of much research in conjunction with the development of innovative monitoring technology designed to prevent sudden failures. This paper investigates the use of AutoRegressive Integrated Moving Average (ARIMA) model to predict the time of slope failure. Input data such as inverse velocity (IV) and dimensionless inverse velocity (DIV) from 20 slope failures were used to train the model predict the failure time. For comparison purposes, the time of slope failure using the traditional inverse velocity method is also provided. We show that ARIMA provides 90% more accurate predictions than the TIV approach.

Jul 12, 2023

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By M. Piboule et J. M . Charbonneau, C. Picard

In the western part of the Chapais syncline (Abitibi-east, Quebec), the lava flows belonging to the Haliy Formation separate in two distinct sequences. The basal sequence contains prophyri tic metabasalts of calc-alkaline af f inity overlain by porphyritic metatrachyandesites and metatrachytes of alkaline to shoshonitic affinity. The upper sequence contains porphyritic metabasalts similar to those of the basal sequence along with highly potassic metaandesites trending to a subalkaline affinity. A geochemical study of trace and REE elements established that the composition of these lava flows results from a mixing or contamination process. The primitive tholeiitic liquids which are enriched in LREE were modified by the addition of a crustal contaminant enriched in Y, Zr, Th and K20. The magmatic liquids resulted from successive steps in the admixing process, evolved by fractionated crystallization. The mechanism of gradual admixing seems to be the major cause of the observed ea le-alkaline characteris ties and may also be the cause of the alkaline to shoshoni tic affinity in those lavas. The tendency to differentiation by fractional crystallization reveals the tholeiitic character of the primitive liquids.

Jan 1, 1984

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Dan Brown

Renewal and revitalization of transportation presents a challenge in the need for replacement, repair, and improvements of existing bridges, as well as increased construction of transit systems within existing transportation rights of way. Difficulties with conventional deep foundation systems occur because of the limited site access, adjacent structures, the need to maintain traffic, and other constraints on construction activity. Major projects are often performed in a design-build contract environment in which the schedule is aggressive, and where speed and reliability represent major considerations. Foundation designers are confronted with a need to solve problems with a construction-oriented mindset, where typical experience with lowest cost solutions may not reflect the most effective approach. This presentation presents an overview of the challenges that may affect design and construction of deep foundations in this environment and the methods that have successfully been employed on several large transportation projects in the U.S.

Jan 1, 1900

The purpose of this study was to investigate the immobilization as a host for metallic pollutants (Cr, Cu, Pb, and Zn) by ettringite phase. Ettringite phase is produced through hydration reaction of calcium aluminate with gypsum. From the XRD patterns, it is known that the distance between spaces in 010 planes in ettringite crystal increase with an increase of ionic radius of heavy metal except Pb; no big difference is shown. For this reason, the d-value of 010 planes in ettringite crystal increased with the substitution of Cr, Cu and Zn having a big Al ironic radius. But in case of Pb, because the substitution occurred at calcium site, it does not influence to increase d-value of 010 planes.

Jan 1, 2006

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002