Search Documents

Caissons hand dug to a depth of about 100 feet were used to underpin three important structures at an industrial site in the State of Utah. The caisson shafts extended through 30 to 40 feet of coarse, granular soils and 25 to 60 feet of sands and clays to bear on a very dense, coarse gravel and cobble stratum near the water table. The shafts were belled to 12 feet square at their bearing elevation. Bearing pressures of 20 ksf were assigned. The shafts were lagged with timber. The use of hand-dug caissons allowed continuous operation of the facility during underpinning. Settlements after underpinning have been minor and well within the estimated magnitudes. Instrumentation was placed in two of the caissons with varying degrees of success.

Jan 1, 2010

By Marc Leduc

Since co-disposal technology promises to replace conventional tailings disposal methods at sites with high strip ratios or plentiful old dumps. While the mine waste needs to be relatively strong and low in fine material, and chemical compatibility must be assured, when these parameters are satisfied there are no other significant hurdles to its implementation. In this sense, the paper describe the resulting benefits range from substantial reduction in capital and operating costs to reduction or essential elimination of the short- and long-term liabilities associated with tailings dams are impoundments.Since tailings dam failures are arguably the greatest environmental liability and public relations problem in the industry, reducing the quantity of tailings managed behind dams is a worthy goal.

Jul 31, 2003

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

Competition in the mining industry is the main driving force for both equipment manufacturers and end users to develop and apply the most cost efficient solution to a mining problem. Therefore the challenge to find new solutions is usually met by several suppliers under various factors of influence affecting specifications. Time and timing are particularly important, but all new developments ultimately have to successfully perform on site.Consideration of all aspects of planning, manufacturing, user liaison and ultimate satisfactory commissioning hinges on the necessities of assessing of all the expectations in the mining application and the requirements of the concept and layout team. To apply the maximum available technical competence with solid thorough workmanship is the best possible foundation for success of underground machinery development.

Jan 1, 1991

By R. J. Matetic

Researchers associated with the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), are investigating injuries (fatal and nonfatal) attributed to water well drillers during well drilling activities. Injury data, obtained from various sources, suggest that many water well drillers are experiencing unnecessarily high insurance premiums and very avoidable citations or violations from the direct result of accidents, injuries, and fatalities occurring throughout the water well drilling industry. Expensive insurance premiums and unnecessary citations are the direct result of poor health and safety practices. Visits to numerous water well drilling sites were conducted by NIOSH personnel to characterize and identify the injury data collected and to provide inexpensive strategies to prevent, minimize, and eliminate safety and health issues associated with water well drilling activities.

Jan 1, 2001

By Gábor Antal, József Bõhm, Barnabás Csõke

From the waste material of the production of aluminium foil aluminium pigment is produced for the paint industry by grinding it in white spirit. During grinding 1-2 % iron impurity gets into the product, weakening its quality, from the wear of the mill armour and the grinding bodies and from the contamination of the raw material. For deironing the product, a stage-operated electrically induced magnetic filter separator was developed and put into operation. The separator was sited in an explosive environment and therefore required a special design and safety system. The paper describes the results of the development work. the device that was developed, the safety system as well as the results of and experiences with the operation of the separator.

Jan 1, 1995

D. C. JACKLING, the father of the porphyry coppers, has been honored for his pioneering in that field. There is another facet to Mr. Jackling's activities, one which now may prove an even greater monument than the big coppers-the story of his venture in taconite beneficiation. The essence of his porphyry development was mass handling of material. Not alone mining on a large scale, which was done on the Mesabi Range at the turn of the century, but the integration on a previously unknown scope of mining, milling, concentration, and in many cases, of final reduction to metal at the site. This was mass production applied to mining, treatment of a very low grade source material, previously considered submarginal.

Jan 1, 1954

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

By M. A. Ford

This paper reviews the history, sources, mineralogy, extraction metallurgy, conversion, and enrichment of uranium in South Africa. Over the past 40 years extraction plants were built at 27 sites, an9.over 140 kt of uranium have been produced. Older plants have had to adapt to changing market conditions, no single technology has had the opportunity to become entrenched, and costs have been reduced to a third of those of the original flowsheet. The research efforts aimed at developing the country s nuclear raw materials have been particularly rewarding, as they have enabled South Africa to become a world leader in the extraction of uranium from low-grade ores and to develop methods for uranium enrichment and the production of nuclear fuels.

Jan 1, 1993

By M. C. Rockwell

There are about 1.8 Mt (2 million st) of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia currently stockpiled in a tailings pond at the mill site. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a potential source of soil conditioner material for the local market. However, the fine particle size, 98% passing 147 pm (about 100 mesh), and a moisture content of 20% make their handling, shipping, and application to soils difficult. The tailings were agglomerated into small hard pellets with various amounts of soil nutrients, moisture content less than 13%, and pH values ranging from 6.5 to 8.7.

Jan 1, 1987

Chlorination of organic matter by direct injection of chlorine gas or hypochlorite has been investigated metallurgically worldwide with little understanding of the basic chemistry of the passivation mechanisms in- volved. In this paper, chlorination of carbon is attributed to oxidation-reduc- tions, resulting in surface halogenation of graphitic or amorphous carbon. It is proposed that chlorine and carbon interact to form thin coatings of chioro-carbon complexes that block the adsorption of gold cyanide com- plexes, thus passivating the gold adsorption sites of carbonaceous matter. Analytical, spectrographic, microscopic and electron-optical methods have been applied to demonstrate the proposed mechanism of chlorine-carbon bonding, as well as to evaluate the advantages and limitations of chlorination in the pretreatment of refractory carbonaceous gold ores.

Jan 1, 1991

By A. E. Isaacson, T. H. Jeffers

The U.S. Bureau of Mines (USBM) is investigating arsenic removal from dilute waters using a biological precipitation/chemical adsorption system. The method includes (1) inoculating water with ferrous salts to increase hydrogen sulfide generation by indigenous sulfate-reducing bacteria, (2) utilizing the hydrogen sulfide to precipitate the bulk of the arsenic as arsenic sulfide, and (3) using beads containing ferric oxyhydroxide to remove the remaining arsenic. This approach was applied to a contaminated water containing 13 mg/L As. Arsenic extractions up to 99% were achieved. The use of sulfate-reducing bacteria is particularly warranted in this situation since most of the required nutrients are present in the water. Based on successful initial efforts, planning is underway to conduct a pilot-scale test at the site.

Jan 1, 1995

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By John D. Nelson, Clint L. Strachan

Drainage of tailings impoundments is a key issue for impoundment stability, water control, seepage control, and reclamation. Drainage control is an established operating practice where climate and site conditions permit, such as in South Africa and various mines in North America. In these areas, drainage control is primarily used to maximize tailings densities and to provide adequate impoundment stability. Drainage practices during operation also become an important issue when tailings impoundments are reclaimed. Time required for cover placement and post- reclamation seepage control depends greatly on the ability for tailings to drain and consolidate. This paper discusses drainage issues associated with gold tailings impoundments in terms of mechanics of saturated and unsaturated flow and experience with design and reclamation of tailings impoundments.

Jan 1, 1988

By J. Murphy

The economics of microbial coal desulfurization are affected significantly by the proper selection of the plant site and by maintenance of variables at suitable levels. High sulfur coal particles below 200 mesh show sulfate production rates triple those with 150 mesh coal but grinding costs are greater. Slurry solids density increases from 5% to 20% reduced the rate constant by a factor of 10. Coal added to a batch reactor in the stationary phase resulted in a sudden second exponential sulfate production phase indicating feasibility of lower cost continuous operation. Successful operation in the absence of beef broth, yeast or added nutrients at non-sterile conditions enhanced projected economics. Finally, the need for adequate agitation and aeration was well established.

Jan 1, 1985

By Richard C. Harris

Substantial economic benefits exist today for fine coal preparation and improved technologies coupled with more stringent air quality standards should increase those benefits in the future. The costs of cleaning can be determined with reasonable certainty with proper consideration given to mining methods, plant feed characteristics, refuse disposal and marketing impact. The benefits cannot be as accurately determined but include impact on generating capacity, plant maintenance, emission standards, slagging, fouling, transportation, and handling. Site specific cleaning offers particular benefits in some situations to tailor the preparation plant facility to boiler characteristics. Improved communications and methodologies need to develop to allow the coal producer and the coal user to clean coal to the degree that results in the lowest overall cost for electrical generation.

Jan 1, 1988

By William C. Peters

The experiences of exploration crews with mineral land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. A single step, such as that of taking a series of deep soil samples, is sometimes delayed until some sense can be made from floating unpatented claims which are obscure in orientation as well as position-placer claims, overlapping lode claims, location posts with empty Prince Albert cans and claims with no apparent assessment work for ten years. Add to this some patented claims without monuments, a state or federal withdrawal area which may or may not invalidate preexisting claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights.

Jan 1, 1970

By Lawrence W. Teufel

An anelastic strain recovery technique is presented as a method of determining the directions and ratio of the maximum and minimum horizontal in-situ stresses from oriented cores from deep wells. Predictions of hydraulic fracture azimuth inferred from principal stress directions determined from both elastic and time-dependent (anelastic) strain relaxation measurements of volcanic tuff are consistent with the observed orientations of hydraulic fractures produced in simulation and mineback experiments, underground at the Nevada Test Site. In addition, anelastic strain recovery measurements on oriented cores of shale and sandstone from well depths of about 1680 meters show consistent relaxation directions of the principal horizontal strains and have enabled a prediction of the principal horizontal stress directions and hydraulic fracture azimuth.

Jan 1, 1982

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By R. Corriveaau

This paper is about a horizontally curved conveyor, which carries 6,050 stph of limestone over land from a new quarry to the owner's plant. The conveyor is 5,012 ft long with a horizontal curve radius of5,OOOft Site conditions made a curved conveyor design the most optimal and economic solution. Using our unique custom conveyor calculation program, TKRI was able to accurately model and design the conveyor to properly track the belt and prevent any spillage through the horizontal curve radius. A data monitoring system was installed that allows monitoring of the conveyor both locally and remotely. The remote monitoring allows TKRI to contact the owner for preventive maintenance. Preventive maintenance can reduce the conveyor downtime during normal operating hours.

Jan 1, 2004