Search Documents

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Ronnie X. Gu, Xing Zheng, Gem-Yeu Ma

Due to implementation of the rotator construction method from which a smooth shaft was anticipated, a full-scale pile load test (Osterberg Method) was performed at Pier 14 Pile 9 of the main span of the New Benicia-Martinez Bridge to confirm the design parameters of the rock sockets. Two levels of load cells were fabricated in the reinforced cage of the rock socket. Each level consisted of three 670-mm Osterberg load cells with a total testing capacity of more than 50 MN in both directions. In an attempt to separate side friction and end beari ng, a 75 mm thick compressible Styrofoam material was placed at the bottom of the cage. The pile load test was carried out in four stages. The multi-level multi stage pile load test data was interpreted for casing friction, side friction for two rock strata, end bearing, and residual side shear values under repeated loading in opposite directions. The side friction from the casing in soils at Stage 2 is approximately 9 MN. The end bearing at the tip of the rock socket at Stage 3 was calculated to be approximately 17 MN at a displacement of about 75 mm. The residual side shear resistance for the 10 m 50% RQD rock strata was calculated to be 9 MN or approximately 50% of initial values, after being pushed 0.3 mm upward in Stage 1, 71 mm downward in Stage 2, then 55.5 mm upward again in Stage 3, and finally 105.3 mm downward in Stage 4. The test results surprising ly indicate that the side shear resistances from both low RQD intensely weathered rock and higher RQD slightly weathered competent rock are about the same at approximately 19 MN. This pile load test provides very critical information for confirming deep shaft design and analyses.

Jan 1, 2005

By T. Yamazaki, T. Goto, R. Arai, N. Nakatani

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has been recognized these 30 years. The thin layer-type coverage and the micro-topographic undulation of basement affect not only the excavation efficiency but also the economy of mining venture. Because of these distribution characteristics, no economic feasibility has been recognized through the past economic analyses. On the basis of a recent geological study about seamount rocks, a possibility of by-product substrate recovery for phosphorous supply with cobalt-rich manganese crust mining has been highlighted. In the mining model, the substrate rocks are utilized as phosphates for agricultural and chemical usages. Under some preliminary technical and economic assumptions, the possibility of cobalt-rich manganese crust mining venture is examined. The results show a better economy of the venture including the substrate rock usage for phosphorous supply. Introduction Cobalt-rich Manganese Crusts and the Economic Feasibility Cobalt-rich manganese crusts on the Pacific seamounts received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and higher cobalt concentration than manganese nodules (Cronan, 1980; Halbach, 1982; Manheim, 1986). In the earlier stage, the geological distribution characteristics were reported (Cronan, 1984; Clark et al., 1984; Misawa et al., 1987; Pichocki and Hoffert, 1987) and a systematic feasibility of the mining was studied (Hawaii DPED, 1987).

Jan 1, 2018

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By J. J. Wallaert

The decreasing supplies of natural gas and low-sulfur crude oil available for electric power generation in the United States will unquestionably shift the emphasis to nuclear and coal fired steam power plants in the immediate future. Failure to do so will ensure our dependence on mid-east low sulfur crude oil comprising some 70% of the known world reserves, and imported liquid natural gas. By contrast, the United States has 43% of the known world reserves of anthracite, bituminous and semi-bituminous coal and 48% of all known coal reserves of the world including lignite. It is evident, therefore, that coal is alive and well and will continue to be a significant energy source for the production of electricity for many years. Of course, concern for our environment and the development of new technologies will ultimately curtail the utilization of coal for the generation of bulk power, but information released by the National Electric Reliability Council and the Federal Power Commission is worth repeating. In the year 1972 the total capacity of generating units in the United States was 379,552 Mw of which 149,974 Mw, or 39.5% of the total, was produced by coal fired steam turbines which consumed 344,700,000 tons of coal. New capacity additions planned or in construction show that in the year 1981 our total generating capacity will be 843,503 Mw, of which 257,995 Mw, or 30.6% of the total, if from coal only. Translating this increase into terms meaningful to the bulk material handling industry suggests that ten years from now the utility industry will require 590,000,000 tons of coal per year - a monumental task - if we are to sustain our current demand rate for power.

Jan 1, 1973

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By D Chalmers

"There is a tendency to treat mine roadways with fan installations as leak proof systems. Morecomplex ventilation arrangements are being installed in coal mines out of necessity or designand these can introduce additional hazards. This paper explores the leakage paths that can existaround fans and in particular the hazards these leakage paths may generate around undergroundfan installations. The behaviour or these leakage paths in the event of a fan failure has also beenexplored. Early detection of spontaneous combustion is essential, so understanding the leakage behaviour around fans especially boosters or main fans installed underground will assist in sett ing up monitoring locations in the correct places. If this behaviour is not fully understood then monitoring may be placed incorrectly, or trends may not be picked up until it is too late."

Jun 1, 2012

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By A. L. de Vegt

For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m /d. A pilot plant started operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop the processes for metal and sulfate removal from groundwater and selective copper recovery from leach water. The principle of the biotechnological methods, full scale experience, and an overview of the test program at the copper mine are presented.

Jan 1, 1997

By X. Shi, V. Vallyathan, N. S. Dalai

"Using. ESR spin trapping methodology, evidence was obtained that fresh quartz dust in a cell-free aqueous medium generated hydroxyl - and possibly superoxide radicals. The hydroxyl radical generation potential decreases on storing of fresh quartz dust in ambient air and on the addition of either catalase, superoxide dismutase, desferoxamine, or DMSO. The role of quartz related radicals in the biochemical mechanism of acute silicosis is suggested from these findings.IntroductionThis report summarizes our electron spin resonance (ESR) detection of oxygenated radical formation by freshly crushed quartz particles in a cell-free aqueous medium, and its inihibition by radical scavengers. This study was undertaken with to elucidate the primary biochemical mechanism involved in the development of silicosis (Farber, 1983; Reiser and Last, 1979; Silicosis and Silicate Disease Committee, 1988). In particular the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood (Farber. 1983; Reiser and Last, 1979;). It is generally believed that the action of quartz particles on the cell membrane is the starting point of the silicotic process (Farber, 1983; Parazzi et al., 1968). Thus the surface characteristics of the quartz particles have been the subject of several recent studies (Bolls et al.. 1983; Dalai et al., 1986; Fubini et al., 1987). Recently, We reported that mechanical crushing of quartz under normal atmosphere generates free radicals which decay with time, and that these free radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to aged dust from the same stock (Dalai et al., 1986; Vallyathan et al.. 1988). The formation of Si• and. SiO--type of radicals from quartz particles crushed under atmospheric conditions has also been reported by Fubini et al. (1987). In addition, Gulumian and van Wyk (1987) have reported that quartz particles react with hydrogen peroxide (H202) to generates hydroxyl radicals (•OH) and suggested that this process might contribute to quartz's pathogenicity. However, these authors did not report the effects of metal chelators, so it was not clear as to whether the detected -OH radicals simply resulted from the Fenton reaction involving exogenous metal ion contaminants. Earlier, Marasas and Harington (1960) reported that quartz particles could function as an oxidant in a number of in vitro oxidations, including the hydroxylation of proline and lysine. They postulated that silica dusts, on reacting with water, could release H2O2 which might have the potential to react with various biological constituents and thus cause tissue damage. In fact, Gabor and coworkers (Gabor and Anca, 1974; Gabor et al., 1975) suggested that the cytotoxicity of quartz particles might be associated with the generation of some 'factor or factors possessing the properties of a free radicals capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently Weitzman and Graceffa (1984) reported that asbestos is able to catalyze the generation of • OH radicals from H2O2. Their later work indicated that lipid peroxidation may be one of the mechanism by which asbestos produces tissue injury (Weitzman and Weitberg, 1985). This is significant because • OH radicals are capable of causing peroxidation by abstracting hydrogen atoms from cell-membrane lipids and initiating lipid peroxidation in lysosomal membrane (Fong et al., 1973). In fact, the formation of oxygenated species in reactions involving quartz was suspected since Kolbanev et al. (1980) reported the detection of H2O2 in the reaction of fresh quartz particle with aqueous medium. The present work was thus undertaken to detect the anticipated formation of some oxygenated, radical species by reactions of quartz in a cell-free media and its inhibition by radical"

Jan 1, 1988

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By R. Reeves

Coal producers and utilities depend on automated coal blending systems to reduce costs and meet stringent environmental regulations. Over 30 systems installed in the United States since 1987 use on-line PGNAA (Prompt Gamma Neutron Activation Analysis) analyzers to accurately control the blending process. Experience and detailed engineering are required to integrate real-time data produced by the coal analyzer with a control system to meet demanding performance specifications. This article reviews successful installations and lists important features including interfacing analyzers with plant control systems, specifying feeders and weigh scales, and managing data.

Jan 1, 1995

By Andre L. De Vegt

For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (HzS). The HzS reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S00 can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.

Jan 1, 1996

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia's total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By B. J. Jody

At Argonne National Laboratory, we have been developing a potentially economical process to recycle automobile shredder residue (ASR). We identified three potentially marketable materials that can be recovered from ASR and developed technologies to recover and upgrade these materials. We built and tested a field-demonstration plant for recycling polyurethane foam and produced about 2,000 lb (907 kg) of recycled foam. Several 300-lb (I36-kg) samples were sent for evaluation and were found to be of marketable quality. We are also preparing for a large-scale test in which about 200 tons (181 tonnes) of ASR-derived fines «0.25 in. [<0.62 cm]) will be used as a raw material in cement making. A major cement company has evaluated small samples of fines prepared in the laboratory and found that they meet its requirements as a substitute for iron ore or mill scale. We also produced about 50 lb (23 kg) of recycled acrylonitrile butadiene styrene (ABS) from obsolete automobiles and found that it has properties that could be readily upgraded to meet the specifications of the automotive industry. In this paper, we briefly discuss the process as a whole and summarize the results obtained from the field work on foam and fines recycling.

Jan 1, 1996