Search Documents

By Gary H. Higgins

The paper by Lewis and Braun l presents experimental and calculational evidence that primary chalcopyrite ores are rapidly oxidized by warm oxygen-bearing water. Resulting solutions contained copper sulfate products of the matrix rock decomposition such as magnesium sulfate and sulphuric acid. Iron was oxidized to insoluble hematite and hydrous iron sulfates. Oxygen injection near the base of a broken and permeable flooded ore deposit was calculated to cause circulation of oxidizing solutions to the entire permeable region. The rate of dissolution of copper and degree of oxygen saturation for given oxygen injection rates were presented. Their work suggests that in-situ recovery of deep, disseminate primary copper deposits is technically feasible. The actual feasibility depends on economics and environmental safety as well, and it is the purpose of this paper to address these two aspects.

Jan 1, 1972

By Rimas Veitas, James Panton, Erich Steinlechner

"Ductile Iron Piles (DIPs) are a proven, viable alternative to conventional piles, and for the past five years have been successfully used throughout New England. The installation process of DIPs lends itself to both large and small projects. Because of their installation efficiency they provide a substantial cost savings over drilled micro piles. Several New England projects (both end bearing and friction) will be evaluated, focusing on the installation and design procedures.BackgroundThe driven ductile cast iron pile (DIP) is a simple, fast and highly effective pile system. Over the last 30 years over 10 million feet of this pile system has been installed worldwide predominantly in Europe. DIPs are a prefabricated driven pile system utilizing high strength ductile iron pipes which are manufactured using a spun-cast process having outside diameters of 4 5/8” and 6 5/8 inches. The standard pile lengths are 16.4 feet long. The pipes are manufactured with a tapered socket with an internal shoulder for full engagement at the top and a tapered spigot at the bottom. The individual pile sections can be connected with this Plug and Drive® connection to drive a pile of any length.(see figure 1)The DIP system’s inherent advantage is the simplicity of the installation process. The piles are driven to refusal or to a required penetration depth with the use of a high-impact highfrequency hydraulic hammer (ie. Breaker hammer). In most applications the hydraulic hammer is mounted on an appropriately sized excavator (see Photo 2). At the completion of driving the pile, the pile is cut off (see photo 5) and the remaining section of pile is fitted with the appropriate driving shoe and serves as the lead section for the next pile. Being able to reuse the cut off section, yields minimal if any pile shaft waste. The pile is then fitted with an appropriate pile cap plate to receive the load from the superstructure."

Jan 1, 2017

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By S SSdbom

A comparison was made between chemical analysis and ocular mineral/rock classification in health-based risk assessment of historical mine waste produced between 1625 and 1975. Large parts of the mine waste are heavily weathered and secondary minerals are abundant. The field was divided into several areas from where composite samples were collected. Seventy-five mine waste samples were selected for chemical analysis (As, Cd, Co, Cr, Cu, Hg, Ni, Pb, V and Zn) and ocular mineral/rock classification (silicate, mica, granite/pegmatite, carbonate, iron oxide ore, sulfide ore, distribution between chalcopyrite, sphalerite and galena and distribution between pyrite and pyrrhotite). The waste has been produced in conjunction with mining a complex sulfidic ore with increasing iron oxide content (mainly magnetite) towards the northern part of the field. Elevated concentrations were found for Cd (average 26 mg/kg dw), Cu (average 3500 mg/kg dw), Pb (average 4100 mg/kg dw) and Zn (average 11 000 mg/kg dw). Large differences between average and median values indicated that the data was not normally distributed, ie the metals occur as discrete minerals (eg chalcopyrite, galena and sphalerite). The ocular classification indicated low carbonate content, chalcopyrite dominating over sphalerite and galena in most samples and an even distribution between pyrite and pyrrhotite. Both analytical and ocular mineral/rock classification data were combined into a common matrix that was evaluated using multivariate statistics. Principal component analysis (PCA) showed, for instance, that chromium and vanadium were mostly associated with harder minerals and rocks. PCA also indicated that a similar graphical picture could be obtained for chemical data and ocular mineral/rock classification data, respectively. The comparison indicates that ocular mineral/rock classification can replace or at least reduce the numbers of chemical analysis in health- based risk assessment of historical mine waste.

Jan 1, 2008

By Richard Wells

Peabody Energy is the largest pure-play publicly traded coal company in the world. We have been in business 129 years and like most of the coal mining companies in the United States, since 1969 the majority of our safety improvement efforts had been driven by compliance with the various versions of the Federal Mine Safety and Health Act and the supporting federal regulations. In 2004 Peabody Energy management came to the understanding that in order to achieve our goal of zero incidents, that focus must change. This paper will describe the elements of the journey we began at that point to make the transition to a behavior and systems-based approach to safety management and our efforts to win the minds and hearts of our employees. This journey is undertaken with the goal of making safety truly a way of life for all Peabody Energy employees.

Aug 1, 2013

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

By M Ozkayhan, N Arslan

"The Efemçukuru underground mine in western Turkey is an intermediate sulfidation, epithermal gold deposit. The bulk of the mineral resources and all of the mineral reserves lie within the Kestanebeleni (KB) vein system. This system comprises four spatially-distinct mineralised zones: the south ore shoot (SOS), the middle ore shoot (MOS), the north ore shoot (NOS) and the KB north-west ore shoot. Production currently occurs only in the SOS, MOS and NOS zones. The gold mineralisation is very fine grained and occurs as free grains in quartz and carbonate, and as inclusions in sulfide minerals. Gold is recovered as part of a sulfide concentrate by flotation methods. Though hosted in the KB vein, the gold mineralisation is not evenly distributed within the veins. Definition of its occurrence is totally dependent on diamond drilling.Diamond drilling at Efemçukuru is done with its own equipment and staff, all managed by the mine geology group. The process over the mine’s six year production history incorporates continual improvement with an innovative approach by focusing on the following: drill team organisation career development and training product research and effective equipment management cost reduction planning and scheduling of development for drill stations.Over 40 000 metres of mostly BQ size core are drilled annually by three drill rigs at a cost approaching US$35/m.The planning and execution of the drilling pattern depends on the configuration of the ore shoot and the planned mining method. Ore extraction is mainly by drift and fill mining augmented by about 15 per cent longhole stoping. The drilling of a specific area is scheduled to be finished 3 to 8 months prior to mining. This scheduling is sufficient for short-term grade model updates and any needed changes to the planned development or stope sequencing prior to planned production from the stope area.CITATION:Arslan, N and Ozkayhan, M, 2017. Diamond drilling at Efemçukuru gold mine, Turkey – a case study on the benefits of timely and cost-effective drilling to short-term planning, in Proceedings Tenth International Mining Geology Conference 2017, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By Daniel C. McLean

Extraction data for Cu, Zn and Fe were obtained from 4.5" and 10" columns using massive sulfide ore and natural acid mine water. The purpose was to determine if recycling of solution through the column would produce leach liquors of 4 g/l Cu and Zn at extraction rates of 1 g/l per pass at typical flow rates of 0.002 to 0.006 gpm/sq.ft. Test results exceeded expectations. Cu and Zn concentrations of 4 g/l were obtrained within 4 to 6 cycles. Concentrations greater than 6 g/l Cu and 8 g/l Zn were reached within 10 cycles. Concentrations of greater than 40 g/l of Fe and free sulfuric acid were obtained with no decrease in biological activity being observed. No reagents were used.

Jan 1, 1995

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By M. Melih Demirkan, Juan J. Gutierrez, Raghav Ramanathan

"As the capital of the United Arab Emirates (UAE), Abu Dhabi is one of the world’s fastest-developing cities. To sustain its significant growth rate, Abu Dhabi must surmount challenging engineering problems in the most efficient manner. One of the challenges facing Abu Dhabi is ground settlement caused by poor groundwater control practices in inherently difficult subsurface conditions. For construction projects in Abu Dhabi located near the Arabian Gulf, groundwater is frequently encountered and must be accounted for and addressed during design and construction. Abu Dhabi City CenterRecently, the Abu Dhabi government developed a geodatabase by digitizing, processing and qualifying an extensive amount of existing information (i.e., more than 26,000 borehole logs). Because of the evaluation and processing of the geodatabase, detailed maps of geotechnical and hydrogeological surface features were generated using 3D modeling. Ultimately, the geodatabase was used to develop risk maps indicating geohazards, such as sabhka (or salt flats), uncontrolled fill and cavities. This information identifies the location and extent of the areas vulnerable to surface subsidence. Dewatering can change pore water pressure, which, in turn, alters the effective vertical stress in a soil mass and can affect groundwater chemistry. Changes in pore water pressure and groundwater chemistry can significantly affect soil and rock. The potential effects of dewatering include:• Change in effective stresses and shear strengths in soils• Increase in seepage velocities and pressures• Erosion or transport of soil particles and piping• Settlement• Collapse of subsurface cavities or voids• Transport of groundwater containing contaminants• Dissolution of soluble materials, such as rock salt or gypsum"

Jan 1, 2017

By Art Johnston

Gas handling at Magma Copper company's, San Manuel smelter receives process gas from a flash .smelting furnace and four copper converters. The major gas handling equip11lent consists of four electrostatic precipitators and a sulfuric acid plant. Process ,vessels in gas handling are, typically confined, spaces. Lethal gases, mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence': of hazardous chemicals and explosive gases in process' vessels and piping are of major concern when repairs' are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards ,involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adequately trained and prepared to treat the injured person without becoming victims' themselves. The methods used at Magma Copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992

By Jürg Künzle

The use of the underground space has been a recurring issue in human history, whereas the reasons for building subsurface structures have changed over time. In the decades to come, the world will be marked by a variety of underground projects never before seen. This paper describes a series of characteristic challenges of designing and building underground freight transportation systems, with reference to the example of Cargo sous terrain, a privately funded underground logistics project in Switzerland. It provides an overview of contracting practices that allow these challenges to be addressed with success.

Jun 13, 2021

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021