Search Documents

By Ryan Sullivan, Lisa Smiley, Jewels Stover

The Westerly Storage Tunnel (WST) Project is part of Project Clean lake, the North East Ohio Regional Sewer Dist years. When completed in 2020, WST will be nearly 2 miles of 25-ft diameter tunnel 200-250 ft below ground. The storage tunnel will manage higher flow volumes, keeping stormwater out of the combined sewer system reducing overflow occurrences. Three deep shafts provide access to the tunnel at the tunnel boring machine (TBM) launch and retrieval sites, as well as a vent shaft. Support of excavation for the access shafts was constructed utilizing unreinforced concrete diaphragm walls. This innovative, value-engineered alternate design significantly reduced risks associated with conventional secant piles combined with a rib and liner plate system. Implementation of the diaphragm wall technology resulted in a water tight, continuous shaft keyed into rock. This case study examines the design, methodology, and installation challenges unique to each shaft, as well as the benefits of the final product to the overall project.

By K. F. Unrug

Fractures of sedimentary rocks in the vicinity of the outcrop are commonly encountered around the world. Mine highwalls and numerous highway cuts give excellent views for detailed study of surface fractures. This paper gives an explanation of the origin of fractures as well as characterization of the distribution and extent of joint system with reference to lithologic composition of the rocks. Practical implications of the joint system affecting mine operations are described. Among the subjects discussed are: discontinuous deformation as an effect of surface subsidence, stability of mine portals and near outcrop underground operations, and stability of highwalls, when using highwall miners and strip operations. Some design procedures are recommended that can minimize the problems encountered in mining areas with intense joint systems.

Jan 1, 1994

By R. J. Matetic

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the fieldsite. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 2010

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By C Roche, G M. Mudd

The Morobe Province of central Papua New Guinea (PNG) has been mined for gold for nearly a century, although it is only in the past decade that large-scale modern mining commenced. The Hidden Valley gold-silver project began construction in mid-2006 and production by August 2009, and is located in the mountains above Wau in the headwaters of the Watut River. The mine is owned and operated by the Morobe Mining Joint Venture (MMJV), which also owns the Wafi-Golpu project, comprising the Wafi gold deposit and Golpu copper-gold deposit, situated in the Watut River Valley. Together they represent a potential mine of the scale of Ok Tedi or Bougainville or bigger. The MMJV is owned in equal shares by Newcrest Mining from Australia and Harmony Gold from South Africa. Although Hidden Valley was the first large-scale mine in PNG to engineer and build a tailings storage facility, poor environmental management during construction and early operations led to significant erosion of waste rock and sedimentation impacts throughout the ~200 km length of the Watut River. Since then, substantial efforts have been made to improve environmental management, especially waste rock placement and storage and water quality management. While the impacts from the Hidden Valley project appear to be reducing, the saga has heightened concerns by many along the Watut River and across PNG about ongoing impacts from mining.This paper presents the results of an ongoing project in the Morobe Province conducted by the Mineral Policy Institute examining the historical, current and future impacts of mining, including community views, social and environmental impacts and the monitoring and regulation of mining. Overall, there is a clear need to more fully integrate social and environmental issues into life-of-mine planning and go above and beyond regulatory requirements. In this way, some of the lessons learnt – by the community, MMJV and government – can be incorporated before, during and long after mining.CITATION:Mudd, G M and Roche, C, ?2014. Mining in Morobe, Papua New Guinea – impacts, assurance and self-determination, in Proceedings Life-of-Mine 2014 , pp 313–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By K. C. Dean

The Bureau of Mines, following passage of the Solid Waste Disposal Act of 1965, was authorized to conduct research on methods for utilizing, stabilizing, or reclaiming mineral wastes. This report summarizes laboratory research conducted by the Bureau and cooperative field studies made with the mineral industry to reduce the environmental impacts of air and water pollution deriving from mineral wastes. Utilization research showed that both dry-press and steam-cured building bricks and ceramic tile could be made from copper mill tailings and other discarded mineral wastes. Sponge iron was produced from steel mill and amination industry wastes, and valuable mineral products were extracted from such diverse sources as flue dusts and uranium tailings. Mineral wastes were combined with agricultural and/or sewage wastes to make artificial soils that have the potential of resolving several disposal problems by production of a useful commodity. Physical, chemical, and vegetative stabilization methods were evaluated, singly and in combination, for reclamation potential on copper, uranium, lead-zinc, and asbestos tailings. Suitable methods were developed in the laboratory for overcoming major adverse conditions of these wastes such as salinity, heavy metal toxicity, acidity, basicity, lack of nutrients and organics, and unstable surfaces. Field testing of these methods was performed on a variety of mineral wastes. Costs for the various stabilization and utilization-procedures developed were also determined.

Jan 1, 1986

By Jamel Sgaoula

During 1998 COGEMA Resources Inc. announced that operations at the Cluff Lake mine will be suspended indefinitely by the end of year 2000 as a result of deteriorating uranium market conditions. To remain profitable, Cluff Lake mine started an aggressive cost reduction program. A cost reduction team was formed to look for ways to lower production costs. The focus of this team was to screen all areas and to come up with ideas to improve the economy of the mine and ensure the viability of the operations over the remaining three years of operations. Among the areas where significant savings were achieved are: (1) replacement of portion of cement with fly ash in backfill; (2) backfill optimization; and (3) new shotcrete plant installation on site for bulk in-house shotcrete production. This paper details the research work carried out by Cluff Lake mine on these projects and results of its application.

May 1, 2001

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By D Yates, C C(te, M Rodgerson

This paper describes how specific technical and regulatory issues related to water management have been dealt with at Anglo AmericanÆs Moranbah North mine. It compiles the collection of practices that have been implemented since 2010 in response to climatic and regulatory drivers. Operations must continually evolve as they face emerging challenges. For Moranbah North mine, one key challenge is the integration of its mine water system to that of its new neighbouring mine Grosvenor. The commitment to ongoing improvement has placed the mine in a good position to face this particular challenge.Water-related risks were identified then mitigated by technical practices, which have focused on improving underground water management, increasing storage capacity and installing a state-of-the-art control system for the management of water on-site and for releases of mine-affected water to the environment. These practices are supported by an extensive monitoring and audit system that provides confidence in the reporting of activities and outcomes. The strategy has helped the operation with its continual attempts to minimise reliance on high-quality third-party water and improving its interaction with the surrounding environment and community.CITATION:Rodgerson, M, Yates, D and C(te, C, 2013. Leading practice water management at Moranbah North Underground Mine, in Proceedings Water in Mining 2013 , pp 301-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining' machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

By Richard D. Hagni

An enhanced Interest in pyrometallurgical dusts has recently emerged due to increased world-wide environmental concerns. Mineralogical study of dusts samples from lead sinter plants. lead smelters, and secondary steel mill electric arc furnaces has shown that they can be readily studied by reflected light microscopy. These dusts typically are composed of small particles sufficiently large that their mineralogical identification and characterization can be conducted under the reflecting light microscope. Scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) has been used to confirm optical identifications and chemical compositions. The sinter and blast furnace dusts at the Doe Run Smelter at Herculaneum, Missouri are commonly about 20-150 11m. They consist predominantly of galena, chalcopyrite, sinter. slag. coke. and particles. Dusts from remote sampling sites 112-1 mile from the lead smelter are composed of similar particles and abundant fine-grained particles, less than 10 um. of locally derived calcium-aluminum silicates. Electric arc furnace (EAF) dusts are mostly spherical and less than 10 11m. They consist predominantly of iron oxides (magnetite. franklinite. jacobsite and solid solutions of these spinels), zincite. and calcium-iron silicate glass, together with smaller amounts of hematite. sylvite. coke and metallic iron. Reflected light microscopy is rapid provides mineralogical data on individual grains within dust particles. and allows direct observations of textural intergrowths in pyrometallurgical dust particles.

Jan 1, 1991