Search Documents

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By H J. J Boshoff, A J. Karrasch

Mine planners frequently face the challenge of mitigating the impact of climatic events on mining operations, such as floods and droughts. Specific water management infrastructure can be implemented to meet operational requirements in response to these events. However, the effect of flood protection, for instance, may reduce the resilience of the site to drought. The probability and duration of unfavourable climate sequences significantly influences the net present value (NPV) of implementing specific water management infrastructure.Good life-of-mine planning will consider the incremental development of the project, and provide staged development plans. Water management infrastructure and the timing of implementation are facets of this process.CITATION:Boshoff, H J J and Karrasch, A J, 2016. A decision-making framework for water supply and flood protection options in net present value terms, in Proceedings Life-of-Mine 2016 Conference , pp 196–199 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By J Jones, J Blunt

"The requirement for environmental approvals and associated environmental impact assessments (EIAs) is now commonly regarded as a key milestone and body of work during project development. EIAs can be undertaken at various phases during project development, generally either:\ during the scoping or prefeasibility studies, where limited project information is available and the mitigation and management measures of the EIA become a set of criteria and commitments that control project design during the feasibility study, as an iterative approach whereby mitigation and management measures are developed through an integrated process with the engineering team, and measures are included in the feasibility study cost model following the feasibility study, where detailed project design information is available, the cost model is complete, and the EIA is an assessment of a fixed project with limited opportunities for mitigation and management measures to be integrated into engineering design. This paper investigates the advantages of integrating EIA into life-of-mine planning during the feasibility study phase, using the Tampakan Copper-Gold Project (the Project) as a case study. The Tampakan Project is located in the Philippines on the southern island of Mindanao. The Project involves the proposed development of three main areas of infrastructure:a large-scale, open pit copper-gold mine and associated mine site infrastructure (including tailings and mine waste storages, fresh water dam, concentrator, etc) a power station, port and filter plant (PPFP), located approximately 60 km from the mine a pipeline and transmission line linking the mine and PPFP sites.Examples of engineering measures developed through an iterative process to mitigate and manage predicted environmental and social impacts include design of water management infrastructure, modification of the disturbance footprint (eg roads realigned to avoid critical habitat) and realignment of project infrastructure to minimise impacted water catchments.CITATION:Blunt, J and Jones, J, 2012. Integrating environmental impact assessment into life-of-mine planning, in Proceedings Life-of-Mine 2012 , pp 143-152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By J. Kretschmann

Mining heritage can be of outstanding value for many regions around the world, because mining has been done for thousands of years for the benefit of mankind and its development. This paper presents an ongoing project creating a general guideline for the handling of mining heritage on the basis of experiences made in Germany. Interactions of stakeholders in the ?heritage network? as well as strategies for the technical proceeding will be described. An action plan for the sustainable handling of mining heritage has already been developed in part, which includes necessary measures. Best-practice recommendations will be derived. Keywords: m ining heritage / preservation / guidelines / action plan / Sustainability

Feb 27, 2013

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By J Plinke

The imperative to operate sustainably requires all equipment and processes to operate at their maximum possible efficiency. Achieving this ideal state requires a thorough understanding, not only of the process itself, but also of the tools available to design and assess potential improvements. This paper presents a case where the widely employed Discrete Element Method (DEM) toolset proved insufficient to model problematic material flow during the process of optimising wet screening performance. A Smoothed Particle Hydrodynamics (SPH) model was found to more accurately replicate the flow characteristics of the physical system. Site observations identified biased loading of the screen decks to cause inefficiencies in the wet screening of an iron ore processing circuit. Two numerical modelling approaches were pursued with the aim to select the most suitable one and continue the optimisation process based on that selected model. Selection criteria were established, based on the minimum requirements of being able to replicate the problem, including the main flow dynamics deemed to cause the issue. The DEM model was found to over-simplify the slurry flow dynamics within the scrubber and no laterally biased flow was introduced by the scrubber’s rotation to the otherwise symmetric system. Since DEM was not able to accurately replicate the existing problem, it was deemed an unsuitable method to assess the effect of any changes to the system. The second approach consisted of a SPH model. This model was deemed to map the flow within the scrubber with sufficient accuracy to address the problem, as it produced biased screen loading comparable to that reported from site. Changes to the wet chute, delivering material from the scrubber to the screen, aimed to neutralise the non-centrality introduced via the scrubber, were then successfully designed and assessed using the SPH model.

Nov 8, 2021

By COLIN A. LAWRENCE, Anthony Del Vescovo

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2017

By David R. Sutfin, Joseph Lodde

110 N. Carpenter is new commercial building located in the West Loop neighborhood of Chicago, Illinois. The new home to the McDonalds Corporation work headquarters, accelerated project delivery methods were essential to meet the scheduling demands for this project along with other projects slated to start in the region. As such top-down construction methods were utilized to allow for above and below grade construction to proceed in parallel in lieu of more conventional bottom-up construction methods, thus compressing the project schedule. To achieve this plan, perimeter secant pile walls were constructed in conjunction with interior columns/drilled shafts and a shear wall core constructed from inside a temporary cofferdam. The use of secant pile walls allowed for efficient accommodation of a variety of loading conditions including: exterior curtain walls loads, perimeter column loads, tower crane foundation loads, and in-plane shear loads. Furthermore, this system allowed for efficient and fluid operation of equipment on site in order to accommodate the 90-day window allotted for initial foundation construction. INTRODUCTION 110 N. Carpenter is a recently-constructed 9-story commercial building located on the old Harpo Studios property in the West Loop neighborhood of Chicago, IL. The construction of this 55,750m2 (600,000 ft2) structure is significant to the continued commercial development of Chicago as nearly 46,450m2 (500,000 ft2) of the building houses the new world headquarters for the McDonald’s Corporation, which had moved from Chicago to the suburb of Oak Brook in 1971. McDonald’s recommitment to this urban environment is not only a reinvention of the long-established fast food giant but the anchor for a broader redevelopment of the West Loop neighborhood. Since the opening of this building was seen by the developer, the City of Chicago and others as a key to future local projects, innovative solutions were required to showcase forward-thinking design as well as expedite the construction process. The final result of the design/planning process is a structure consisting of nine levels of above-grade commercial space and two levels of below-grade parking, providing approximately 300 parking spaces. The above-grade structure consists of a reinforced concrete flat plate system, including two-way slabs, columns, and two core/shear wall systems for lateral support. With an average depth of 7m (23ft), the below-grade structure consists of interior components similar to the above-grade structure (structural slabs, columns, shear walls) but includes a perimeter secant pile wall that was designed to support lateral earth pressures; vertical forces from the exterior curtain walls, perimeter columns, and the construction tower cranes; and in-plane lateral forces to reduce the demand on and quantity of interior shear walls. The use of a secant pile wall is a key component to the project because it accommodated the use of top-down construction methods to accelerate the construction schedule.

Jan 1, 2019

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By Carlos Torres, Albert Cabrejo

For the last 20 years mine slopes have been monitored with slope stability radars. Since 2015 a group of dedicated geotechnical engineers dedicated to remotely monitor radars around the world have detected 2000+ slope failures of different characteristics. A statistical analysis of the information gathered of these failures have been made and the summarized results are presented with some degree of analysis appropriate for the vastness of the database. The analysis considers different types of commodities, countries, mining processes, rock types, and weather conditions.

Sep 29, 2023

By S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By R. C. Adams

This report describes the feasibility of mining the oil-shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt, at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By J. E. Gebhardt, B. Temel Mckenna, W. Lee, C. S. Macomber

X-ray diffraction (XRD) data was extracted from various sources to develop qualitative ternary and tetrahedral plots differentiating mineralogy, bond work index (BWi) and hardness of ore bodies at different mine sites. A large number of historic reports and compiled characterization laboratory data were used to create a searchable "data lake." The data lake provides a means to locate, consolidate, and visually represent XRD from disparate sources. Visualizations with large amounts of mineral ore XRD characterization data provide a qualitative assessment of ore properties, including comminution qualities such as material hardness. The visual map can be employed to quickly estimate expected ore character and behavior, given XRD analysis of samples from newly characterized and unfamiliar ore. Keywords: Mineralogy, Characterization, Comminution, Database, Ternary, Tetrahedral

Jan 1, 2020

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By R Dunne, W McCallum

Continuous improvement might be defined as seeking incremental improvement over time through improved equipment, processes, technology and the efforts of people. Most people working in ore processing facilities embrace the general principles of continuous improvement. However, given the industry-wide issues with skilled personnel and the constantly changing environment in ore processing facilities, it is often difficult to identify improvements in a facility over a given time period. The driver for these outcomes is the use of basic principles and technology to achieve best practice targets. The process involves four stages: develop standards of practice to define best practice in specific areas; write procedures to guide the organisation towards these best practices; implement the procedures and develop a review process to provide a method of measuring performance against best practice.By reviewing performance against best practice on a regular basis, the organisation measures progress towards the best practice targets and the incremental improvement between these regular reviews is a measure of continuous improvement.This paper provides the background for developing standards of practice for metal accounting, metallurgy and metallurgical management. The paper also describes how standards of practice can be used to develop continuous improvement and the skills set of the departmentÆs leadership team.CITATION:McCallum, W and Dunne, R, 2012. Metallurgical management tools for continuous improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 225-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Mark P. Walsh

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within groundwater aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contaminantion. Since ammonia is one of the constituents of the leach solutions now being field tested, one environ- mental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laboratory experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit. Dispersion attending the flow of fluids in a porous medium is also shown to be an important factor. The effect of dispersion can greatly reduce the benefits of having a displacing cation which is adsorbed selectively with respect to ammonium. Since dispersion increases almost linearly with fluid velocity, an optimum displacement rate may exist.

Jan 1, 1979