Search Documents

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York's total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914

By H. Basarir

Due to the environmental constraints and the limitations on blasting, ripping as a ground loosening and breaking method has become more popular in both mining and civil engineering applications. Because of the technological advances in dozer manufacturing techniques, more powerful dozer types are available today. Thus, the ground, previously classified as non-rippable, has become rippable. As a consequence, a more applicable rippability classification system is needed which considers both equipment properties as well as rock properties in all applications. This paper is part of a complementary research work and presents the development of a previously published grading rippability classification system by the application of fuzzy set theory. The integrated rippability classification system considers the combined utilization of the rock and equipment properties, as well as expert opinion. Fuzzy set theory was chosen mainly because it deals well with uncertainty in the choice of variables. Although there are apparent sharp or discontinuous boundaries in existing classification systems, practically most of the factors involved in the ripping process are less well defined and boundaries are more blurred (or fuzzy) or uncertain in nature. Also by means of fuzzy logic it is possible to eliminate bias or subjectivity. The validity of the proposed system was checked by the comparison against existing classification systems and direct ripping production values obtained at studied sites. It is seen that by means of fuzzy logic, the uncertainties are reduced and biased usage of the final ratings that appear in alternative systems are efficiently dealt with. Keywords: Fuzzy set theory, rock rippability, rippability classification system, direct ripping, fuzzy inference system.

Jan 1, 2007

By Mandeep Singh

The smelting of lead ores has been carried out in southeast Missouri for centuries, and modern smelting practices have generated a variety of waste products. Lead blast furnace slag is one such product, which typically contains 10% zinc, 25% iron and 2% lead. This slag has often been stockpiled on the producing smelter site and accumulations have now reached several million tonnes. It is possible that in the near future these slags will be classified by the federal Environmental Protection Agency as hazardous, and therefore there is considerable interest in possible treatment processes to render the slags non-hazardous by removing the offending metallic elements. To ensure that the overall slag processing costs are kept to a minimum, it is imperative that lead and zinc be recovered in a form suitable for sale or further processing. There are two generic routes for processing blast furnace slags and they involve hydro-metallurgical or pyrometallurgical techniques. With hydrometallurgy, the slags would be leached directly and the metal values recovered from purified leach solution(s) by electrowinning. One problem with processes of this type is that the zinc and lead grades of the slags are low and the iron content is high, and thus the economics of metal production are often not favorable. For pyrometallurgical processing (1), it has been shown that the slags can be fumed to produce an oxide dust containing all the lead and zinc, and representing only a fraction of the weight of the initial slag. The oxide dust may then be processed hydrometallurgical to recover zinc and lead.

Jan 1, 1992

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the pact 32 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued to emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced. American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

The first metal-mine accident-prevention course was prepared and published 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circulars on accident prevention at metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By D. E. Van Dillen

Seven configurations for panel entries of a longwall coal mine are compared and ranked according to structural stability. These entry configurations are analyzed using three-dimensional finite element modeling The models include large dimensions to minimize boundary effects, elastoplastic constitutive relations, and simulated excavation and construction of support systems. The stability criteria are formulated in a quantitative manner to facilitate the ranking of the entry configurations. These criteria are based on the expected volume of caved rock in the entry openings. The stability ranking is applied to the entry excavation phase, the headgate phase, and the tailate phase of the entry life cycle. Parametric variations are applied using two-dimensional finite element models to determine the sensitivity to changes in mining and design parameters.

Jan 1, 1981

By E. D. Gardner

This paper is the third of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. The second papers deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in the second paper applies to all forms of placer mining. The present paper treats of dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

By Bernard Lewis

This report on the research and technical studies conducted by the Explosives Branch of the Bureau of Mines covers the 2-year period July 1, 1946, to June 30, 1948. A report for the fiscal year 1947 was omitted because of the large amount of work still in an unfinished state. The material presented herein is based largely upon more comprehensive reports prepared under the authorship of members of the branch staff.

Jan 1, 1949

By John C. Machisak

INJURY experience and employment data for the nonmetal mining industry in the United States are presented for the calendar year 1958. Statistical tables 6 to 12 give detailed information on injuries and employment at nonmetal mines. Data for nonmetal mines are presented separately from those for nonmetal mills, tables 23 29. The Bureau is authorized to send questionnaires to the nonmetal industry for their voluntary submission on of injury and employment experience at their operations. As this information contributes to the promotion of safety in the nonmetal mining industry, every effort has been made to make these questionnaires as complete as possible.

Jan 1, 1962

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By W. F. M. GOSS

For the purpose of procuring data that could be used in estimating the value of the briquetting process as applied to American fuels, the United States Geological Survey, in cooperation with other interests, began in 1904, at the Louisiana Purchase Exposition, certain experiments involving the production and use of bituminous-coal briquets. It installed at St. Louis, and later at Norfolk, machines for the manufacture of such briquets, and the output of these machines has been tested in locomotive service on several different railroads in comparison with natural fuels. An elaborate and carefully executed series of tests involving the use of natural coals and of briquets made from the same coal, previously crushed, was carried out on a locomotive mounted at the testing plant of the Pennsylvania Railroad Company at Altoona, Pa.; and some preliminary experiments involving the use of briquets in marine service were made in connection with one of the Government's torpedo boats. A description of these tests is presented herewith. The results sustain the following general conelusions: 1. The briquets made on the Government's machines have well withstood exposure to the weather. and have suffered but little deterioration from handling. 2. In all classes of service involved by the experiments, the use of briquets in the place of natural coal appears to have increased the evaporative efficiency of the boilers tested. 3. The smoke produced has in no test been more dense with the briquets than with coal; on the contrary, in most tests the smoke density is said to have been less when briquets were used. 4. The use of briquets increases the facility with which an even fire over the whole area of the grate may be maintained.

Jan 1, 1911

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011