Search Documents

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By N Murphy and, S Santomartino, M Cramer

Acid rock drainage (ARD) can have detrimental effects on mining infrastructure, water reuse options and environmental discharge. As a result, some form of short- or long-term treatment is required at many mine sites. Successful treatment depends on a number of factors including the selection of an appropriate treatment technology and its correct implementation. A variety of passive and active technologies are available for dealing with ARD. Passive treatment solutions do not require continuous chemical inputs but take advantage of naturally occurring chemical and biological processes. They are often low cost, site specific approaches and are predominantly used in post-closure situations. Passive systems are well suited to drainage with low acid loads and low soluble aluminium concentrations, and are more effective with highly reduced (ie low oxygen) water. While they are often regarded as permanent fixes, most require some form of ongoing maintenance and all have an engineered life expectancy (ie finite carbonate and organic matter budgets). Passive treatments include, oxic limestone drains, anoxic limestone drains, limestone diversion wells, various reducing and alkalinity producing systems, pyrolusite limestone beds, aerobic and anaerobic wetlands, permeable reactive barriers (organic ¦ carbonate and zero valent iron), slag leach beds, and gas redox and displacement systems (GaRDS). Active treatment solutions require a continuous or semi-continuous activity (eg reagent dosing) to correct water quality issues. They can be engineered to treat virtually any type of drainage or site specific ARD issue, and have no set acid load or redox limitations. Tasks handled by active treatment systems are almost invariably larger and more costly than for passive systems. Active treatment approaches include; pH control, adsorption/absorption, ion-exchange, electrochemical concentration, biological mediation/redox control, flocculation/filtration and crystallisation. A range of generally available and proprietary technologies has been developed around these approaches. Active treatment involving pH correction with alkaline amendments is the most common and cost-effective form of ARD treatment. A variety of fixed plant and portable treatment systems are available. Calcium-based reagents, including quicklime (CaO), hydrated lime (Ca(OH)2) and limestone (CaCO3) remain the reagents of choice for the majority of active ARD treatment worldwide. This is principally due to their widespread availability, non-proprietary nature, and variety of proven dispensing technologies and cost-effectiveness. Limestone, in particular, is a very low cost reagent. However, due to æefficiency of useÆ problems with limestone in passive treatment systems, combined with its very low cost, there has been a recent emphasis on developing active treatment systems that use limestone efficiently. As the requirement for treatment increases, there is a growing emphasis on treatment sludge management and sludge stability. The final choice of a suitable treatment technology is dependent upon water chemistry (eg pH, type of metal contamination, acidity), flow rates, acid load, local natural resources (neutralising materials, topography), climate, site logistics, environmental risk and economics. The benefits and limitations of both passive and active treatment technologies are summarised.

Jan 1, 2003

By H. Hejny

Given the current status of political discussion in Europe about raw materials issues, the sustainable development of the extractive industry and the reduction of its environmental and societal footprint are among the key topics in this discussion. In this context, the European Commission approved the EO-MINERS project (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation). The overall aim of EO-MINERS is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry, authorities, and the society in view of its sustainable development while improving its societal acceptability. Developing generic, standardised and reliable EO-based products to monitor the environmental and societal footprint of mining projects is the way chosen by EO-MINERS to improve this interaction, along with the organisation of tripartite meetings gathering all relevant stakeholders. The project uses existing EO knowledge and carries out new developments on three demonstration sites (Sokolov lignite mining area, Czech Republic, Witbank coal field, South Africa, Makmal gold mine, Kyrgyzstan) to further evaluate and demonstrate the capabilities of integrated EObased methods and tools in monitoring the environmental and societal footprints of the extractive industry during all phases of a mining project, from the exploration to the exploitation and closure stages. It contributes providing reliable and objective information about affected ecosystems, populations and societies, to serve as a basis for a sound ?trialogue? between corporate stakeholders, governmental organisations and societal stakeholders. The project already developed a set of consolidated indicators based upon previous knowledge about mining-related issues along with interviews of national, regional, and local stakeholders. These indicators reflect known environmental and societal issues at mining sites as well as the interest of various relevant stakeholder groups. The process described in the EO-MINERS project ? policy assessment > indicator identification > choice of suitable EO tools able to serve monitoring task > monitoring by EO tools > making available objective information for fair dialogue among stakeholders ? is generally applicable to all stages of a mining project. The key to success will be the right choice of indicators addressing the problem and subsequently the right choice of suitable EO tools and finally the willingness of all stakeholders to find a common solution. To this end, the EO-MINERS project organises site-specific ?trialogue? workshops at each demonstrations site, which aim to provide relevant information in adequate quality to the stakeholders as common ground for discussions. Local stakeholders, including mining companies, regulatory bodies, and community representatives are invited to participate in these workshops where the relevance of the developed EO-based products to environmental and societal impact assessment will be discussed. The presentation will discuss results obtained during these trialogue workshops, as well as the success and difficulties and reluctances encountered. The project will further indicate ways and means how the EO products and other project results may be used for monitoring purposes in all phases of a mine.

Aug 1, 2013

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

By Abdulazeez Rotimi, Barry Sheppard, Abid Adekunte

Good engineering practice is a function of sound theoretical knowledge, first-hand experience on previous projects of similar scope and scale, good acquaintance with case histories of similar projects completed by others in similar environmental conditions, as well as satisfactory degree of exposure to state-of-the-art methodologies. The four factors itemised above are typically interdependent. They amalgamatively influence the judgement of the Engineer and they ultimately result in the delivery of safe and cost-effective solutions by Professional Engineers. This technical paper presents detailed information on the ground engineering aspects of a large-scale housing development project located on a sloping site that had been presumed to be unstable in West Sussex, England. The ground engineering design package for the scheme comprised of temporary working platform designs & stability assessment for piling rigs and other construction machinery, geostructural designs for approximately 1km total run of permanent bored pile retaining walls to support the split-level construction on the sloping site and geostructural designs for the permanent foundation piles to support the housing units. The paper details how the four factors outlined above were amalgamated by the project’s foundation specialist consultants & piling contractors to deliver safe and practical solutions for the development, with significant savings in materials, cost and project completion time.

Sep 8, 2021

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By Julia Herhold

The demand for sustainable and profitable/efficient projects within the tunneling and other underground engineering sectors grows rapidly. Construction tasks play a key role within the project conduction, whether as primary (tunneling), secondary (e.g., mine securing) or tertiary processes (e.g., workshops). The construction tasks of primary processes create the main structures, such as tunnels, which resemble the main project goal. For the secondary and tertiary processes, the purpose of the task shifts. The main goal is to provide structures, such as the securing of the cavity and workshops, that enable the project and enhance the efficiency of the primary conduction underground. To plan and optimize the conduction of construction tasks underground, whether they are identified as primary, secondary or tertiary tasks, the work preparation can be used. This method, known from the above ground construction, can be adapted and used underground. The approach of a digital work preparation tool combines, connects and adapts the main tasks “choice of procedure,” “logistics” and “site planning.” In addition, the digital tool is connected with digital models (construction, site, surroundings). With the adaption and forward projection of the work preparation, underground constructions (e.g., tunneling) can provide a more sustainable and efficient outcome.

Jun 13, 2023

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Ran Tamir

"This document introduces the use of drone generated aerial photography to collect and analyze fragmentation data for both muck piles and post crusher stockpiles in order to support the continuousimprovement process. In tandem with photo analyses software, drone imaging gives mines and aggregate sites a fast, accurate and economical method of benchmarking and optimizing the process of size reduction to spec."

Jan 1, 2017

By Sandeep K. Sharma

The U.S. Bureau of Mines has been investigating new techniques to improve the of mineral to recover water lost in the waste slurry, and to produce dewatered solid dewatering s suitable for disposal. As part of this investigation, a study was undertaken to investigate the feasibility of dewatering Alaska placer effluent. Based on the laboratory tests, preliminary field tests were conducted on three placer mines in Alaska. At these mines, the water recovered from the placer effluent (250 to 23,000 NTU) exhibited turbidities of 20 to 240 NTU. In the second year of the project, a large-scale dewatering unit was set up at a mine located in the Livengood district. The feed, at flow rates up to 935 gpm, was mixed with dilute PEO solution in a flexible plastic hose with and without static mixers. Feed to the dewatering unit generally ranged between 300 and 26,500 NTU and required PEO dosages of 0.02 to 0.14 lb per 1,000 gal to produce water from the screen underflow with turbidities of 20 to 50 NTU. During this period, a small unit was also operated at Dow rams of 10 to 25 gpm at sewn sites throughout Alaska, with the effluent from four of the sites being dewatered successfully.

Jan 1, 2010

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. In order to develop a scientific basis for selection of appropriate modifiers it is necessary to understand their adsorption mechanism(s). Specifically, adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for non-ionic polymers. However, a literature survey of Poly(ethylene oxide)(PEO)-oxide system suggested PEO, a non-ionic polymer, to be substrate specific. A systematic study was undertaken to investigate the adsorption mechanism(s) of a PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work characterization of PEO binding sites on oxides is reported and the mechanism(s) of PEO adsorption discussed.

Jan 1, 1997

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence co-efficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculatlon methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By M Bellamy

The DeGrussa copper deposit was discovered by Sandfire Resources in April 2009. Construction of the 1.6 Mt/a concentrator, open pit and underground mining operations commenced in March 2011 with first concentrate production achieved in October 2012. Over the next ten years, DeGrussa grew to include both the DeGrussa and Monty underground mines, establishing itself as one of the world’s premier copper producers with total production of 663 000 t of contained copper by the time the mine closed. Final ore was trucked from Degrussa on 5 October 2022. This paper examines the mine closure experience from both a planning and operational perspective. The paper provides an overview of the site’s mine planning process including the factors involved in determining the end of the mine life and how this was tracked and communicated in the lead up to the end of mining operations. It will also look at some of the specific operational aspects involved in maintaining steady state production all the way through to the last day while facing increasingly challenging conditions. These factors, along with the external factors faced by most of the industry such as labour shortages and COVID related disruptions, contributed to making it an interesting journey to the end of operations at DeGrussa.

Mar 29, 2023