Search Documents

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By Armando Vazquez

This paper will provide an overall technology update on Tenova’s modular i BOF® technology package for improved endpoint detection (Carbon and Temperature), slop detection and auto-tapping control, with a primary focus will be on Tenova's Slop Detection System (SDS). Accurate Slopping prediction is a critical tool in the operation of a BOF. It provides the steelmaker with an additional protective system to increase yield & productivity while reducing operating costs. Tenova Goodfellow's i BOF® slop-detection technology uses lance vibration analysis with real-time alerts to give steel makers advance warning of the onset of a slop and a measurement of the slop severity. The system is designed to provide direct feedback control of lance position and oxygen flow rate, for rapid mitigation of potential slopping events. This paper will provide a summary on how the i BOF® technology package has been implemented, including trials and general results.

Jul 30, 2018

By D Yan, D Connelly

Beneficiation of magnetite is an integral part of the future of iron ore processing. Historically, the focus of Western Australian producers has been on exporting direct shipping ore (DSO) namely haematite. The future for new DSO resources is limited so companies are changing their emphasis into processing the very large, undeveloped magnetite ores in Western Australia (WA), using beneficiation to produce shippable magnetite concentrates. These magnetite resources require higher cost processing techniques such as fine grinding and beneficiation to produce saleable concentrates. This distinct difference, from the DSO ores, has led to the development of a number of new technologies. This paper reviews: the different techniques used for magnetite beneficiation and provides some case studies in the WA industry; the use of mineral liberation analysis (MLA) to describe the nature, grain size, occurrence and associations of the mineralisation;the consideration of coarse cobbing as a critical upgrading; the application of high pressure grinding rolls (HPGR) to save energy; how the field of magnetic separation has resulted in new machines with higher field strength (SLon Separators); ultra fine grinding requirements of magnetite concentrates; andthe application of reverse flotation to reduce silica in the concentrates.

Jan 1, 2009

By Robert O. Vernon

The discussion of water and pit mining together is most appropriate. In fact, water can be considered a mineral and a well a narrow pit. Thus, of all the mineral resources mined, water is probably the cheapest, most valuable and least valued. The delivered price, including mining, transportation, storage and marketing rarely exceeds ten cents per ton, and our economy would cease without it. The time has come when the public must recognize that the extraction of a mineral resource from the land is a necessary and inevitable result of the industries? attempt to meet the demands of a growing economy. In so much of Florida, the lands mined can, with forethought and planning, be left as improved real estate, water conservation and management lands. On the other hand, the mining industries must face up to the need for the reclamation of land and compact with themselves, appropriate governmental agencies and with the mining states to restore mined lands to usefulness. Of limestone, sand, and clay 90 to 100 percent of the mined material is used, but with planning and specing, these pits, if they penetrate the water table, become valuable as real property. Phosphate, which returns about 70 percent of the mined materials to the pit, can reclaim the land for many purposes.

Jan 1, 1966

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By Joseph Hoang, Nick Reed, Scott Wishart, Michael Lovitt

Marvel Loch Underground forms part of St Barbara Limited’s Southern Cross Operations which is located 360km (224 miles) east of Perth. Southern Cross Operations produces approximately 120,000 ounces of gold each year. Mining occurs in over 8 lodes using a variety of stoping methods including Uphole Benching, Long Hole Open Stoping, and Core and Shell.

Jan 1, 2012

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By I. M. S. Moraes

Caraiba Metais has a plant for the purification and the cristallization of the crude nickel sulfate removed from its copper electrolyte purification system. In November 1994, an interdepartmental group was formed to study the Q.F.D. method, through its application on the improvement of the quality of the nickel sulphate hexahydrate. The team, formed with representatives of the following areas : production, technology, marketing, sales, maintenance, laboratory and TQC office, had also the task of checking the applicability of the method to other products of the comp any. This paper describes the main steps such as the survey of customer's demands, the preparation o1 the quality matrix, stablishing the planned quality matrix, the planned and the designed quality, and the consequent identification of the engineering bottlenecks. It is also shown how these bottllenecks were studied and solved. The application of the method allowed the team to identify means of increasing the production capacity by 40%, to improve the intrinsic quality of the product (including packaging), and to increase the reliability of the process.

Jan 1, 1997

By F. Schreiter

"One method to increase the exploitation rate of a mine is the use of backfill with residual materials in exploited areas. The backfilled material is meant to support both, the walls of galleries and pillars as well as the roof of mining openings. With increasing depth, the exploitation rate diminishes fast, thus the application of backfill in order to change the layout of the mine is crucial for economic success. In result of using backfill, it is possible to change the layout of the working area with a higher ratio to excavated areas and less area occupied by pillars. Thus it is possible to boost the output of a mine by using backfill. Setting the criteria for the selection of the best possible materials and whose improvement, it is useful to know about their qualities and handicaps. The Mining Department at TU Bergakademie Freiberg is analyzing the parameters of residues from different processing methods, accrued in plants of different potash mines and blending different residues for optimization of material attributes. These were significantly characterized by basically parameters like the size and the distribution of different diameters of the grain material. INTRODUCTION The chair for underground mining methods at TU Bergakademie Freiberg is tasked with the sufficient and sustainable supply of economics with raw materials. The steady high demand, the rising prices and the finiteness of the deposits are reasons for the need of an optimized economic utilization of natural deposits, a continuous improvement of mining technics and technology. From an ecological and economical position the best possible utilization of the resources has to be achieved. Many mining operations are by reasons of the deposit not able to haul valuable minerals only, they have to haul a mixture of valuable minerals and waste rock. This hauled combination is given into the processing plant for separation and enrichment of the valuable mineral. The residuals of the processing are commonly dumped to a waste rock pile. For minimizing the size of such a waste rock pile and also minimizing the ecological footprint of a mining operation the only way is minimizing the quantity of accruing waste rock material. Both, optimization of economic utilization and also minimization of waste rock dumps can be realized in one by backfill with processing waste rock material in mined out areas. Especially in mines, mined by room and pillar method, smaller dimension of the pillars are sufficient for safety and stability. By the way less valuable minerals have to be leaved back in the mine and the mine outcome is increasing."

Jan 1, 2015

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By Y. Mitani, H. Ikemi, K. Kitamura, H. Honda

"Instead of carbon capture and geological storage (CCS) that does not rely on structural aquifers, injecting carbon dioxide into sedimentary rock deep underground has been considered. For advection velocity of the fluid is slow, the permeability of sedimentary rock deep underground is low. In order to perform the CCS on the low permeable sedimentary rock, it is necessary to clarify the behavior of long term storage properties of carbon dioxide (CO2).In this study, the permeability and storativity of CO2 injected into low permeable rock has been evaluated. The injection of supercritical CO2 has been conducted on the specimen of Ainoura sandstone (unit weight: 2.39 g/cm3, porosity: 11.9 %) saturated with water by using flow pump method. The experiment has been set up to reproduce the similar condition of deep underground reservoir under 20 MPa confining pressure, 10 MPa pore pressure, 35°C temperature and 3 µl/min CO2 injection rate. In order to prevent an increase in pore pressure, the boundary condition on the outlet side of specimen has been kept a constant pressure.As a result, it has been possible to observe step by step the change of the differential pressure between both ends of specimen. Furthermore, the relative permeability and specific storage of rock under supercritical CO2 injection has been examined by the theoretical analysis of flow pump permeability test incorporating Darcy’s law for two-phase flow. It is observed that CO2 has been transmitted gradually while CO2 stored in the rock. It is also clarified that residual water has existed in specimen after showing the constant differential pressure in the end of the experiment. Using the results of the experiment, 3D core-scale flow-simulation by using TOUGH2 has been conducted due to confirm the flow of fluid and CO2 distribution in the specimen. From the experimental results and analytical solution to them, permeability and storativity are identified, and simulation results support the validity of the experimental results."

Jan 1, 2015

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, bulk-mineable, open-pitable, heap-leachable, gold-silver deposit. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold occurs principally as electrum finely disseminated through intermediate tuffs, and associated with pyrite, at Santa Rosa. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1993

By Kim McKnight

Dupont has successfully incorporated a Floatex Density Separator into its wet-gravity operations for the recovery of zircon from titanium tailings. Results indicate that the Floatex achieved a zircon recovery of approximately 95% while rejecting similar amounts of quartz and other gangue minerals. Additionally, a unit capacity approaching 16 tonnes/hr/m2 was achieved. Results also show that the alumino-silicates can be separated into other product streams that will further improve process economics and minimize waste material. The improved plant feed grade provided by the Floatex has allowed for either an increase in overall plant capacity and/or final product grade. This paper will present the findings from the in-plant study.

Jan 1, 1996

By William Gleason

The mining industry is at a crossroads. Currently, there is an estimated $25 billion worth of projects around the world that have been stopped as the consequence of a dispute or disagreement with their communities, the government or some other stakeholder. Anglo American chief executive officer Mark Cutifani is one who sees the mining industry in need of change and on Dec. 12, he gave the keynote address for the launch the Kellogg Innovation Network?s Mining Company of the Future Initiative?s Development Partner Framework (DPF). The launch was held at the Ford Foundation building in New York City. The DPF seeks to inspire and support the mining industry to adopt a new way of thinking and a new approach to how it secures, nurtures and revitalizes its social license to operate. Working with a diverse group of people from faith-based organizations, nongovernmental organizations (NGO) and other stakeholders, Cutifani often had the rather uncomfortable position of representing the mining industry in a room full of people who are far from the industry?s biggest fans.

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By Neal Lee, Braden T. Lusk, Brendan McCray

"Selection of a blasting agent for optimum performance is based on many variables. Often, a decision is made with regard to product cost and field testing. Defining optimum performance can be difficult, since downstream effects of fragmentation on loading, haulage, processing, and energy consumption are not immediately clear. Many operations are beginning to optimize their blasting programs “on the bench,” by utilizing information generated downstream at the loader and/or crusher. During the evaluation of a blasting agent, factors such as velocity of detonation, gas production, and sensitivity are typicallyconsidered. Alternatively, brisance (“the shattering power of an explosive material distinguished from its total work capacity”1) is not. Brisance affects the immediate area surrounding a borehole. Fractures produced here during the shock phase of detonation are believed to have an important effect on rock movement and fragmentation. "

Jan 1, 2017

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

More and more coal in Australia is extracted by underground mining methods especially by longwall mining. These methods can be particularly sensitive to relatively small-scale structural discontinuities and variations in roof and floor rock character. Traditionally, information on these features has been obtained through drilling. However, this is an expensive process and its relevance is limited to the immediate neighbourhood of the boreholes. The geological uncertainty remains. Seismic surveying, especially by 3D seismic, is an alternative tool for geological structure delineation with growing credibility. In fact, it is one of the most effective geophysical methods available for identification of geological structures such as faults, folds, washouts, seam splits and thickness changes which are normally associated with potential mining hazards. Seismic data even can be used for stratigraphic identification. The information extracted from seismic data then can be integrated into mine planning and design. In this paper, we demonstrate computer aided interpretation techniques for maximising the information from seismic data and illustrate the ability of seismic reflection methods to resolve localised geological features. Both synthetic and real seismic data obtained in recent 2D and 3D seismic surveys from Australian coal mines will be used. Compared with results obtained with drilling programs, the structural definitions from seismic are of unprecedented quality.

Jan 1, 2002