Search Documents

By Joe Rigney, Conrad Stacey, David Nowak, Chris Blanchard, Michael Beyer, John Czach

Originally constructed in the 1930s, the 1-mile-long Sumner Tunnel is 31 feet in diameter and carries traffic deep below Boston Harbor, connecting Boston and East Boston. This project includes both design and construction for the rehabilitation of the nearly 100-year-old tunnel. The primary work includes repairing advanced deterioration at the tunnel crown with new precast arches that will add protection and strengthening. The restoration also consists of upgrading the tunnel systems, including permanently removing 75% of the existing exhaust duct suspended over the roadway to improve the overall ventilation system capacity and performance.

Jun 23, 2024

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By Oliver Schulz

This paper presents the latest references of the Siemens VAI slab casting technology. Following the connect & cast philosophy Siemens VAI has developed technological packages suitable for installation in existing casters of any original supplier, as well as for complete new machines. A major demand on new machines is to adapt quickly to different market demands. This requirement for flexibility can be divided into two actual trends. Firstly into casting a broad range of steel grades, thicknesses and width on the same machine and secondly having installed slab, bloom and billet caster in one steel plant to deliver all different types of needs on the market. Depending on the condition of the existing machine the focus of modernization ranges from the substitution of single components featuring state-ofthe-art technology to complete caster revamping projects. In this paper concepts and references for short machine outages and fast caster ramp-ups at moderate investment costs are presented.

Jul 30, 2018

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By A. D. German

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of tie laws of Ecuador has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State..

May 1, 1930

By Doug Harding

The 3.5 km long Ashbridges Bay Outfall in Toronto, Ontario, Canada was a challenging drive set below Lake Ontario. After a remote machine acceptance due to the global pandemic, an 8 m diameter Single Shield machine launched in March 2021 from an 85 m deep shaft and began its bore in shale with limestone, siltstone and sandstone. During excavation, the TBM and its crew bored a city-wide record of 30 rings in one day, or 47 m of advance. This paper will cover the unique project, from TBM acceptance through to launch, tunneling in difficult conditions, and completion in 2022.

Jun 13, 2023

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Patrik Bloemer

Reliable and accurate furnace bath level data during the melting process is invaluable for good decision making and furnace optimization, while obtaining such information rapidly and safely on a regular basis is of paramount importance. This paper shows how a melting process problem was identified as a concern, how a solution was sought and how a real-time measurement system was tested by simple modification to an existing temperature sampling manipulator. Also how, with furnace power on or off, taking reliable hot heel, fill and running levels could be used to assist melting control, aid decision making and improve safety.

Jul 30, 2018

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone&apos;s benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is &apos;locked-up&apos;; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890&apos;s following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950&apos;s. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By Erich J. Jacob, Volker O. Meldner

INTRODUCTION Our company has made persistent efforts to utilize the very latest cost-saving technology in tunnel design and construction. However, we were relatively late in joining the clan of slurry shield tunnelers. The challenge came in 1973, when our company was low bidder on a major sewer tunnel in Hamburg, West Germany. The tunnel was to be driven under the harbor region through coarse and fine sands with up to 60 ft hydrostatic head of water. Outer diameter was 15 ft, and length was 2.9 miles. This contract appeared right to enter the new field of slurry face tunneling. We gathered a design-engineering team to develop the machine, called it "Hydroshield", and used it on the project. The good performance of the prototype machine encouraged us to improve and modify the equipment design. The very latest model is now in use on a subway tunnel in Antwerp, Belgium. This tunnel is 21 ft outer diameter and 2.4 miles in total length. In terms of excavated volume it is the world&apos;s largest slurry shield contract. While the drive is still in full swing, we are currently preparing for 3 further Hydroshield applications, with diameters ranging from 12 to 32 ft. This paper describes the Hydroshield&apos;s salient design features, operational characteristics, construction reliability and performance levels, as experienced in West Germany and Belgium.

Jan 1, 1979

By Larry L. Snyder

A compact 4.87 m (16 ft) diameter tunnel boring machine (TBM) is capable of boring a 12.2 m (40 ft) radius curve while gripping horizontally, or vertically, as may be required for the excavation of turnouts. The machine&apos;s 5.0 m (16.5 ft) length and a patented machine structure allows steering while boring without causing harmful eccentric loads. An extremely stiff thrust system, rigid front and rear grippers, and the torsional stiffness of a front end electric cutterhead drive combine to create superior machine stability and boring efficiency. A 2.2 m (7.2 ft) diameter prototype, complete with a soft ground shield attachment, was used successfully on a tunnel project in Scotland.

Jan 1, 1989

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer&apos; s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982