Search Documents

By Masaharu Moteki

At present, the Unmanned Construction System (UCS) is adapted on initial operation against the disaster. For instance, it has been used in Unzen. When the scale of the disaster is big, or the danger to a person is big, the UCS is expected as a quick and safe construction technology. The Remote Controlled UCS is introduced into construction site to repair earth-fill embankment or to remove rock, as urgent measures after the disaster outbreak. For improvement of the operability, shortening of the skill time, reduction of the fatigue, examination of the most suitable system (placement of a monitor and the joy stick) of the remote system is a main theme in the Public Works Research Institute (PWRI). In the report of this year, when the operator controls construction machine directly or he controls it using remote system (he can check the situation of site only via monitor), the degree of achievement, construction efficiency and construction precision were inspected. The remote system which is based on the system used at Unzen was developed at PWRI.

Aug 1, 2013

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984

By Eric D. Marks

Fatalities resulting from ground workers colliding with objects and construction equipment accounted for approximately 18% of the total construction fatalities experienced in 2010. Current injury and fatality measuring methods have proven to be inadequate due to their use of passive measures of safety rather than a more active approach, such as the use of leading indicator data (also called near misses) of hazardous proximity situations between ground workers and heavy equipment on construction sites. The objectives are to create and evaluate the effectiveness of a reliable algorithm for collecting and analyzing the resulting leading indicator data from hazardous proximity situations. Numerous experiments emulating typical interactions between workers-on-foot and heavy equipment are used to evaluate the proximity sensing and detection technology. Safety leading indicator data (also called near misses) generated by the proximity sensing and detection technology during the experimental trials are used to create and assess the resulting algorithm. Results from the experiments indicate that leading indicator data generated from these systems can be processed and analyzed to identify hazardous proximity situations and incidents on construction sites.

Aug 1, 2013

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By Charles Sabine

The 27,960-acre Newberry Mountains Wilderness Study Area (WSA) is located in the Mojave Desert, 17 miles east-southeast of Barstow. In 1983, the U.S. Bureau of Mines, in conjunction with the U.S. Geological Survey, investigated mineral resources of the area as part of the wilderness review process. The Newberry Mountains are underlain by Paleozoic metamorphic rocks, Mesozoic plutonic rocks, and Tertiary volcanic rocks. Eleven mines and prospects were examined. Of the seven sites within the WSA, only the Northrup Prospect is mineralized. Only a few tons of manganese-bearing rock, containing 49% manganese oxide (MnO), are exposed, but exploration may disclose larger deposits. The Azucar Mine, a past producer of gold, is the only site examined outside the area that appears mineralized. Sample data from quartz veins exposed at the surface do not indicate that resources are present; however, the occurrence could not be fully evaluated because underground workings were not accessible. Sand, gravel, and stone are plentiful in the WSA, but alternate sources outside the WSA are available.

Jan 1, 1985

By Frederick K. A1lgaier

The Bureau of Mines' Denver Research Center initiated a subsidence research program in 1978. The short ten goals of the program were to determine practical methods and equipment for measuring subsidence and demonstrate these methods by monitoring subsidence at several mines having mining, geologic and topographic variables typical of those encountered in the western United States. Data from the monitoring program would be supplied to cooperating mining companies and used by the Bureau to accomplish the long term objective of developing and validating subsidence prediction techniques applicable to mines in the West. Subsidence monitoring is being conducted at five mines in Colorado and Utah with substantially different mine plans, mining methods, depths of cover, and topography. The monitoring procedures used at each site are similar and include designing the monitoring network layout, installing the subsidence monuments, initial and periodic surveying of the monuments, and processing the survey data. The network layout, surveying methods, and types of monuments vary according to the conditions at the individual sites and the type of data being collected.

Jan 1, 1982

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By M. H. Haycock

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By R. Rushforth

The surge of activity in the solar energy market, spurred by government incentives, has created new and more efficient solar technologies, but issues surrounding land- and water-use have backlogged the full-scale development of solar farms. This paper explores siting solar power plants on degraded or polluted lands, such as mine tailings impoundments. Historically, mining and has been integral to Arizona?s economy, but has dwindled in relevance due to urban pressures and environmental regulations. Currently, it is legal to site solar power plants on degraded or polluted lands, but the question remains whether the economics of this degraded lands solar development is more favorable than developing pristine land. Therefore, we explore economics of developing mine tailings impoundments at both the institutional and financial level. Methods of research for this paper were interviews with government regulators, environmental advocacy organizations, farmers, and mining company executives. Financial models using extant tax incentives show a positive net present value for the installation of solar power plants, even when accounting for the costs of land remediation.

Jan 1, 2011

By Winton Gale, David Oyler, Jinsheng Chen, Christopher Mark

The National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tailgate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

By P Gunn, M Watts

The general goal of passive acid mine drainage (AMD) treatment is to reduce levels of acidity and metals to acceptable levels. Most treatment systems use either an oxidising or a reducing strategy. In oxidising systems, alkalinity is added along with dissolved oxygen; in reducing systems, dissolved oxygen is removed (if present) and then alkalinity is added. It is recommended that small-scale field trials be conducted as part of the methodology of selecting the best remediation strategy at AMD sites. Following successful field trials at the Sullivan Mine AMD, the Pike River Coal Company (PRCC) has shown foresight by using the same system to treat AMD generated as a result of taking a bulk sample of coal at the Pike River coal field. The system reduced acidity by 100 per cent, iron by 99 per cent, aluminium by 96 per cent, nickel by 95 per cent, manganese by 51 per cent and zinc by 99 per cent. The success of this field trial suggests that a system using a reducing strategy may be appropriate for the Pike River Adit AMD site.

Jan 1, 2005