Search Documents

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By Robert L. Lagace

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal minus. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to determine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m2 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to he attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By Koehler Stout

Previous work done by the authors of this report indicates that hydraulically-placed backfill can be strengthened several fold by various placement methods. Sunshine mill tailings were tested by these placement methods and strength increases up to thirty times were achieved over the ordinary placement methods. A computer simulation study of the test stope in the Sunshine Mine showed that a high-modulus fill absorbs up to 27% of normal stresses versus 7% for "normal" fill while reducing maximum convergence 28% versus 8% for "normal" fill. Although high-modulus fill was not placed in the test stope during this contract, various instrumentation was purchased, designed and built to record necessary data in the stope. Stress gauges were placed in the pillars and recorded data corresponded quite closely with theoretical projections.

Jan 1, 1983

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By M. Veiga, L. Lavkulich, R. Pakalnis, M. Ghomshei, S. Baldwin, J. A. Meech

"On July 26, 2000, the Canada Foundation for Innovation announced an award of $1.3 M dollars for The Centre for Environmental Research in Minerals, Metals and Materials, CERM3, at The University of British Columbia. Additional funding was also provided by the British Columbia Knowledge Development Fund ($1.3 M) and the UBC Stewart Blusson Fund ($0.7 M). Annual industrial grants and contracts are providing support funding for the on-going research projects. Corporate membership in CERM3 entitles each participant to a seat on the technical advisory committee (TAC) as well as access to the five laboratory facilities currently under construction. Both the federal and provincial governments will also participate in the TAC through NRCan-CANMET and the BC Ministry of Energy and Mines, respectively. CERM3’s mission is:• to develop innovative methods to deal with environmental problems created by mining activity;• to promote sustainable development as a hallmark of management decision-making; • to produce mining and processing engineers with the required environmental skills; and• to enhance the image of mining in society as a vibrant and necessary component of a modern economy and society which disturbs the environment for the benefit of mankind.CERM3 brings together a multi-disciplinary team of researchers from over 12 departments at The University of British Columbia (UBC) to work on mining-related environmental problems. These include: chemistry; soil sciences; chemical and biological engineering; earth and ocean sciences; microbiology; civil engineering; electrical engineering; metals and materials engineering; mechanical engineering; mining and mineral processing, the Westwater Research Centre; the Institute for Resources and the Environment; and the School of Occupational and Environmental Hygiene. The centre intends to interact with scientists from industry, governments and other universities across Canada and around the world. CERM3 aims to become Canada’s leading environmental research facility for the mining industry. This paper describes the evolution of CERM3 and its coordinated multi-disciplinary approach to mining and the environment. Some of CERM3’s research projects include:• developing new protocols for environmental analyses to provide consistent and reliable assays;• isolating a natural virus for Thiobacillus ferrooxidans and other bacteria responsible for acid rock drainage (ARD);• designing bio-remediation and adsorption techniques for mine effluents;• promoting and enhancing the use of hydrometallurgy to reduce environmental pollution;• examining new approaches to comminution to decrease energy consumption;• developing a magnetically levitated hoisting system to reduce the footprint of a mine operation;• building a state-of-the-art supercomputer network laboratory for mine/mill simulations; and• designing intelligent bulkheads to seal tunnels following mine closure to survive for 1000 years.This latter project involves the establishment of a research station at the Britannia mine site, 45 km north of Vancouver, which will provide a full-scale facility to design the “Millennium Plug” and contribute directly to the solution to one of North America’s worst ARD-contaminated sites."

Jan 1, 2003

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By Albert H. Fay

This glossary is publi~hed- by the Bureau of Mines as a contribution' to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining, quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; an<lgeological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for' each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted. In a compilation of this magnitude, it is difficult, within a reasonable time to verify all definitions as to the latest usage. Much verifying was done and it is hoped that the best and latest definitions have been used. Reference to the publications cited will enable the reader to determine approximately the period when the definition was used. Definitions in use by engineers of high national or international reputation are given first preference. When definitions from different sources are the same, credit is given to the earlier author as being the original or nearest to the original source. Immediately following each term the name of the locality wherein the word is presumed to have originated or is widely used is given, where such information is available. The name of the author or source from which the definition was obtained follows the definition, and serves as a key to the publications listed. The terms selected from the various glossaries and publications examined have been compared with the Webster,

Jan 1, 1920

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By W. J. C. Meynink

In drier regions of the world, total containment of cyanide liquors for rainfalls less than a specific design value is often required by government regulation. For example, in Queensland total containment is required for rainfalls up to 'the 1% annual exceedence probability. In equatorial regions, where rainfall greatly exceeds evaporation, a total containment requirement is unrealistic and this is recognized by regulatory authorities. Regulatory constraints typically require that cyanide concentrations at an agreed downstream compliance point not exceed a specific value more than a specified fraction of the time. While the excessive rainfall prevents total containment, it does provide substantial dilution. This paper outlines a methodology for assessing the distribution of cyanide concentrations at a downstream compliance point in an equatorial region with limited hydrometeorological data. Consider the hypothetical mine environs depicted in Figure 1. The mine is located near the catchment divide and draws its water supply via a gravity line. Tailings from the process plant are piped to a tailings dam on a sub-catchment below the plant site. The objective is to determine the distributions of cyanide species concentrations at a compliance point just upstream of a major settlement to ensure they do not exceed regulatory limits.

Jan 1, 1991

The emerging discipline of ægeometallurgyÆ is not new but is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing commercial and cultural trend towards more effective mine site integration and optimisation. The AMIRA International P843 æGeMIIIÆ project (Geometallurgical Mapping and Mine Modelling) is a major new cross discipline research collaboration designed to provide support for this emerging industry trend. The project is currently supported by 18 global mineral companies and involves collaboration between the CODES Centre of Excellence (University of Tasmania), JKMRC and BRC (University of Queensland) and CSIRO Exploration and Mining. These groups represent recognised research excellence in the fields of economic geology, automated core logging, advanced microscopy and process mineralogy, mineral processing, mine planning and resource optimisation. The needs and challenges of geometallurgy as an integrated activity will be outlined together with the ongoing contribution and aims of the AMIRA P843 æGeMIIIÆ project. The main emphasis is on development of predictive geometallurgical indices for key processing performance parameters that reflect inherent geological variability. The ultimate aim is to provide predictive indices of geometallurgical performance that can be confidently embedded into resource models and used for risk-defined mine planning and optimisation.

Jan 1, 2008

By Martin F. Grier, Nicholas H. Kempton

The Mt. Todd Gold Project in the Northern Territory is a joint venture between Billiton Australia Gold Pty. Limited, a wholly owned subsidiary of Shell Australia Limited, and Zapopan NL. As manager of the project, Billiton is guided by Shell's corporate policy that foremost consideration be given to protection of the environment from unacceptable impact and that sound environmental programmes are to be implemented effectively at all company operations. This policy on Health, Safety and the Environment helps operating companies in addressing environmental matters in a systematic way and gives guidance on the practical implementation of a range of controls to protect the environment. Most importantly, it seeks to do this in a co­ operative rather than adversarial manner. In developing the Mt. Todd Gold mine the joint venturers' environmental objectives have therefore been to plan and operate the project consistent with the highest industry standards and community expectations and in accordance with all Northern Territory government requirements. A development strategy has been designed which minimises environmental effects. Planning priorities have focused on the successful co-existence of the mine with an endangered species of bird, the Gouldian Finch, which breeds in the area; the mitigation of impacts on surface and ground. water qualities; and the protection of significant Aboriginal cultural and archaeological sites.

Jan 1, 1991

By Caren Caldwell, Leslie Thompson

1.1 Biological Process Description Pintail Systems, Inc. (PSI) has developed and in partnership with their clients in the mining industry has applied biological remediation processes for detoxification of spent ore and process solutions from heap leach operations. Contaminants that are treated to mine closure levels or drinking water standards include cyanides (weak acid dissociable and total cyanides), thiocyanate, nitrates and heavy metals. Biological processes are both site-specific and ore-specific processes. PSI specializes in isolating indigenous microorgan­isms from spent ore and process solutions and augments them in the laboratory for enhanced bio-detoxification in the field. Bioaugmentation in the lab is a key to successful heap bio-detox in the field. In PSI's bioaugmentation processes native microorganisms are isolated from the spent ore environment and are tested for contaminant remediation capacity. A majority of the indigenous microbes will be tolerant of the spent ore environment but will not contribute to contaminant metabolism. Indigenous enrichment or biostimulation of these non-working microbes by adding trace nutrients can competitively inhibit the working microbes. For this reason PSI focuses on the bioaugmentation process where non-working microbes are discarded and the working population is enhanced through stress, mutation and exogenous enrichment before it is re-introduced to the heap and process solutions.

Jan 1, 1997