Search Documents

By Yanske TR, Lane WL

The Doc Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 in in height and the use of stinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction hecoming a major portion of the overall production and have added to the mine life of Doe Run's six operating mines.

Jan 1, 1998

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By D. S. Robertson

More than 700,000 feet of diamond drilling was completed in the Blind River area between 1953 and 1958. Much of this drilling was at depths which are still not usual in North America. However, as the tendency is to deeper holes, factual data from the Blind River operation may well provide information of value in future programs. Rates of drilling decreased with in-creasing depth, but uncommonly good rates (an average of over 50 feet per day over more than 4,000 feet of hole) were achieved with proper engineering and care. Costs varied as contractors and geologists became familiar with the area Hole deviation in the Blind River area was locally severe and control of the hole trace became a major problem. Careful surveying was necessary and found to be highly re-liable. It was found that control of the hole trace above 1,500 feet was much more difficult than at depths below 1,500 feet. This is explained by the mechanics of the drilling operation. Various methods of controlling hole deviation were attempted and,

Jan 1, 1962

By Peng-Fei He

CT scanning tests were used to detect the pre-existing fracture systems of 36 cubical coal blocks. Systematic procedures were developed to construct the pre-existing fracture geometry of the cubical coal blocks from the CT images. Based on the constructed fracture systems, the fracture tensor components were calculated to capture the directional effects of the fracture system of the cubical coal blocks. The effect of the pre-existing fracture system and different combinations of confining stresses on the strength and deformability of coal masses was investigated at a preliminary level using some true triaxial test results and the computed fracture tensor components. The strength of the cubical coal blocks in the loading direction was found to be closely related to the summation of the fracture tensor components in the two perpendicular directions to the loading direction and the level of the confining stress system. The deformability of cubic coal blocks in the loading direction was found to be correlated to the fracture tensor component in the same direction.

Jan 1, 2014

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By John R. Bartels

Jan 1, 2009

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By Andrés Recalde

Dado que el riesgo social se ha convertido en uno de los principales factores de éxito o fracaso para un proyecto minero, las familias, comunidades y gobiernos locales en la zona de influencia se constituyen en actores primordiales de un proceso de relacionamiento y acuerdos que debe contribuir al mutuo beneficio. El Modelo o Acuerdo de impacto beneficio (AIB) es una propuesta metodológica desarrollada en Canadá desde 1970, que busca generar consenso entre la empresa minera y las comunidades impactadas social y económicamente por un nuevo proyecto, mediante la firma de un contrato en los que se enumeran los impactos y las medidas de mitigación que se efectuarán en contraprestación para evitar el daño. Los Acuerdos de impacto beneficio permiten guiar el relacionamiento entre las partes, controlar expectativas y mitigar el impacto social. La firma de una AIB es el inicio de la licencia social para operar (LSO), lo que la convierte en un activo intangible del proyecto.

Sep 30, 2017

By Gabriel S. Esterhuizen

The design of support for underground excavations is a complex process in which the interaction between supports and the rock mass must be evaluated. The strength reduction method (SRM) is useful because it provides a stability factor of the supported excavation that can easily be compared between support alternatives. The method is based on numerical model analysis where the stability factor is determined by reducing the rock mass strength until collapse is indicated in the model. This paper presents the results of validation studies that were conducted using the FLAC3D stress analysis software to compare SRMcalculated stability factors to the empirically based Coal Mine Roof Rating (CMRR) and the Analysis of Roof Bolt Systems (ARBS). The objective was to determine whether the SRM, with its basis in mechanics, would predict similar outcomes as the fundamentally different ARBS and CMRR methods with their basis in empirical observations. A total of 450 different scenarios were evaluated in which the geology, horizontal stress, depth of cover, entry width, support spacing, and support length were varied. The results showed that the SRM-calculated stability factors were able to satisfactorily capture both the ?weak bed? and ?strong bed? adjustments in the CMRR. The SRM results were found to be well correlated to the ARBS stability factors for the 450 cases considered. Further analysis showed that the SRM accurately captures the effect of bolt length, depth of cover, and entry width on the overall stability of an entry.

Jan 1, 2013

By Andrew Abraham

Continual improvement is the key to success in today?s competitive global arena. You require tools that promote dynamic quality management, deliver cost savings to your bottom line and provide the foundation for process improvement. ISO 9000 and ISO 14001 management systems and OHSAS 18001 are those tools. Since their inception, the benefits of ISO management systems and registration have been touted as the way to achieve better bottom line results. This spurred many companies to embark upon the road to registration with high expectations. The potential benefits of ISO management system implementation and third party registration that are commonly provided by Registrars and consultants are compelling adverts for success. ISO 9001:2000 is promoted as an essential tool for systematic efficient and affective management controls that provide a framework for analyzing errors and improving a company?s internal operational processes. It also allows companies to comply with internal and external customer and regulatory requirements thus continually improving the quality of their products and services and thus enhancing customer satisfaction. This, in turn, leads to greater customer recognition and increased market share. ISO 14001 implementation and registration may assist your company in reducing its litigation risk, raw material and energy consumption, waste disposal costs and possibly non tariff trade barriers. It should also provide continuity of operations, enhanced operational efficiency and consequently a competitive advantage in the market place. Registration of your ISO 14001 management system should also improve your company?s profile and credibility leading to regulatory flexibility and improved community goodwill. All of this will be a catalyst for improved morale and pride by employees and management alike. Likewise, OHSAS 18001, the latest certification specification for Occupational Health and Safety Management Systems supports Occupational Health and Safety legal and regulatory obligations and compliance, manages & controls Occupational Health and Safety risks and improves performance, safety culture and efficiency. OHSAS 18001 is an audit certification, and not a legislative requirement. Suggested benefits of implementation include reduction in accidents, lost time and associated liability and insurance costs and improving reputation and credibility through demonstrated commitment to health and safety. The foregoing increases access to new customers, joint venture partners and financing The skeptics say these are motherhood statements and lack corroborative evidence, i.e., ?Show me the money!?

May 1, 2003

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By E. Motica

Ores containing uranium and vanadium minerals have been mined from the Salt Wash Member of the Morrison Formation from many localities in the Colorado Plateau region since about 1900. The most productive deposits are in a relatively small area in Southwestern Colorado referred to as the Uravan mineral belt. The mineral belt is a narrow elongate area in which uranium-vanadium deposits in the Salt Wash have a closer spacing, larger size, and higher grade than those in adjoining areas. Pre- 1948 ore production from the mineral belt was 655,000 tons averaging 1.91 per cent V2O5 and 0.28 per cent U3O8. Production during the 1948 to 1964 period was 7,900,000 tons of ore averaging 1.46 per cent V2O5 and 0.27 per cent U3O8. The ore deposits occur principally in the uppermost sandstone unit of the Salt Wash. This unit consists of sandstone lenses formed by a system of aggrading braided streams flowing in an easterly direction generally normal to the mineral belt. These lenses, referred to as channels, are as much as one mile in width and average about 50 feet in thickness and can be traced for several miles along their courses. Areas favorable for one deposits are recognized principally by the following criteria: ( 1) a host sandstone thickness of over 30 feet, (2) the presence of carbonaceous material in the host sandstone, and ( 3) gray mudstones and clays associated with the ore-bearing sandstone. The ore minerals are believed to have been precipitated from laterally migrating solutions; there is no apparent genetic relationship between ore deposits and tectonic structural features. Exploratory and development drilling from the surface is conducted in three phases: first, wide-spaced drilling to find and outline favorable channels; second, moderate-spaced drilling in favorable ground to locate ore deposits; and third, close-spaced drilling to block-out ore. Long-hole drilling from underground stations is used to find and delineate extensions of ore bodies being mined. Due to intense production since 1948 from shallow deposits, best potential for new deposits exists in areas where the ore-bearing unit is 600 to 800 feet deep.

Jan 1, 1968

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By Richard W. Hutchinson, Robert W. Hodder

"Pyritic massive sulphide deposits lie conformably above submarine volcanic rocks, and beneath siliceous and manganiferous iron formations. The massive bodies are often zoned, with a barren pyritic top grading downward into pyrite with sphalerite, and occasionally galena, and a chalcopyrite-rich base. They are frequently brecciated, like the lavas beneath them, which contain pyrite and chalcopyrite as coatings on joints and fractures and as dispersed grains. The lavas also exhibit propylitic, argillic and silicic alteration. These sulphide deposits appear to have formed on sea bottom from fluids escaping through the lavas during periods of exhalative and sometimes explosive volcanism. The process may be comparable to the present deposition of base metals from hot brines in the Red Sea. Some porphyry copper deposits resemble the altered, sulphide-impregnated lavas which lie beneath bodies of pyritic massive sulphide. In porphyry copper deposits, pyrite and chalcopyrite occur as veinlets and dispersed grains in intensely fractured tuffs, flows, sub-volcanic intrusions or other host rocks, characterized by propylitic, argillic and silicic alteration. Metal zoning is present; sphalerite and galena often occur in manganiferous veins peripheral to a shell of pyritic veinlets which encloses the mineable zone of chalcopyrite-bearing veinlets. This sulphide distribution appears to have formed from hydrothermal fluids escaping, either passively or violently, from solidifying magma. The fluids may be comparable to hot brines encountered by drilling in the Salton Sea area of California.There are also important differences between massive sulphide and porphyry copper deposits. The former usually occur in differentiated, mafic-to-felsic subaqueous volcanic rocks, whereas porphyry copper deposits are often associated with shallow plutons and subaerial volcanic rocks of intermediate to felsic composition. Calcic-sodic metasomatism accompanies the massive sulphides, whereas potassic metasomatism characterizes the porphyry cop.per deposits. Further, ages of massive sulphides range from Archean (Keewatin) to Tertiary, but porphyry coppers are Triassic to Tertiary in age. These similarities and differences suggest that massive sulphide and porphyry copper deposits are related tectonically and metallogenetically. The former were generated during early stages of crustal evolution, particularly in Archean time, and were repeatedly derived during early stages of younger, individual tectonic cycles. In contrast, the porphyry coppers developed during the later stages of crustal evolution - later in terms of both absolute age and relative age within younger individual tectonic cycles. They appear in younger rocks generally, and specifically in rocks involved in events of the middle and late tectonic stages of orogenic belts. The massive sulphide deposits are of early-magmatic eugeosynclinal affiliation, whereas the porphyry deposits formed in late-magmatic, predominantly subvolcanic settings at the edge of continental plates, where contemporaneous exhalative volcanism was mainly a subaerial phenomenon. Transitional types of deposits exist and are found on continental margins with flanking eugeosynclinal sequences."

Jan 1, 1972

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By Robert O. Vernon

Urban sprawl, and all its attendant problems, is upon us. In Florida, and much of the rest of the world, this has been intensified by a special problem - the coastal zone - a land of high-intensity urbanization localized where the sea and our citizens interact. Florida is blessed by a long coastline of beautiful beaches, indented by estuaries, lagoons and spring fed rivers. Rocky and sand covered islands invite habitation. A large and varied fauna and flora make recreation an avocation and work a pleasure. Accompanying these people are all the sustaining, and satellite industries that find the climate, labor, and commodity markets, cheap water transportation, and natural resources to be attractive. It is estimated that by the year 2008 a megalopolis will stretch down the Atlantic Seaboard from Georgia to encompass the Keys and extend along the Gulf to Alabama. This city will be fenced by the sea on one side and by the water management works, necessary to provide the water supply for this complex, on the other. What can we do about increasing the amount of water available for this population and decreasing the resultant wastes??? Rarely has there been tendered a more favorable opportunity for a coordinated planning and development project that will provide public access to beaches and multiple use of the coastal lands. Florida, as a peninsula swept by ocean breezes, having a largely indigenous water supply and only the beginning of the pollution of estuarine and coastal waters can cope with air, water and coastal dissipation and pollution, if we have a beginning at providing a constant water supply and at limiting pollution. This answer would appear to lie underground, where the porous limestones are interbedded with impervious fine-grained sediments and ground-water that circulates through these aquifers empty to the ocean and Gulf along the continental slopes.

Jan 1, 1969

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004