Search Documents

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By Dean H. Ambrose

This Bureau of Mines publication summarizes the status of mine electrical equipment reliability research. Failure rate data were estimated from theoretical, laboratory, and field studies. Tables are presented listing reliability characteristics of molded-case circuit breakers, undervoltage relays, ground check monitors, cables, motors, and control circuitry. Application of failure rate data is shown in tables listing maintenance scheduling intervals of components and components that are most sensitive to the probability of hazardous voltages on power distribution systems in the mines. Complete, accurate, and appropriate failure rates on mine equipment are of the utmost importance for reliability evaluations.

Jan 1, 1985

By A. Blackmore, A. Lamoureux, J. Woloshyn

This paper provides an overview of recent applications of Computational Fluid Dynamics (CFD) to combustion related fugitive emissions problems. The aim is to illustrate the capabilities and discuss the present limitations in this field. Examples include design of retrofitted NOx reduction technology in a kiln and in a boiler, and the prediction of pollutants such as SO2 and metallurgical dust emanating from a copper flash smelting furnace. It is demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause problems and testing solutions, and for concurrently assessing emissions reduction and process impact. In addition, the value of CFD for demonstrating due diligence for regulatory compliance is discussed.

Jan 1, 2015

By O. Norman Lotter

The formulation and use of mixed collector suites in sulphide flotation can be traced back as far as 1957 with the work of Glembottskii and his co-workers in Moscow. The subject was reviewed by Lotter and Bradshaw in 2010, and proposed a synergy between ideally-selected different reagent types to deliver improved performance, in particular the in situ catalysis of a xanthate to dixanthogen by a dithiocarbamate. Correctly formulated for a particular application, an optimally arranged mixed collector suite delivers the following improvements to the flotation process: • An increase in the flotation kinetics • Improvement in coarse, or middling, particle recovery • Reduction in total dosage requirement • Best results are found from testing the ratios of the collectors. This is of critical importance. In all an optimally formulated mixed collector system usually delivers an increase in paymetals recovery of 1–4% absolute, with a gain in concentrate grade in the range 10–20% relative. In recent years, the addition of semi-conductor theory and associated electrochemistry has contributed significantly to this toolbox by way of identifying optimum domains of Eh and pH for the flotation of individual minerals. In the case of mixtures of minerals, this is where the mixed collector system delivers significant value by way of presenting a mixed set of collector radicals and dimers in a common Eh and pH domain for overall performance. This calls on a fundamental understanding of organic chemistry, mineralogy, semiconductor theory, and electrochemistry. Whereas the selection of grinding media type effectively influences the Eh, the pH can be easily controlled by pH modifiers. The theory of this system, and some industrial case studies, are discussed.

By M. Yekich, W. R. Reed, G. Ross, A. Salem

"Canopy air curtain (CAC) technology has been developed by the National Institute for Occupational Safety and Health (NIOSH) for use on continuous miners and subsequently roof bolting machines in underground coal mines to protect operators of these machines from overexposure to respirator coal mine dust. The next logical progression is to develop a CAC for shuttle cars to protect operators from the same overexposures. NIOSH awarded a contract to Marshall University and J.H. Fletcher to develop the shuttle car CAC. NIOSH conducted laboratory testing to determine the dust control efficiency of the shuttle car CAC. Testing was conducted on two different cab configurations: a center drive similar to that on a Joy 10SC32AA cab model and an end drive similar to that on a Joy 10SC32AB cab model. Three different ventilation velocities were tested—0.61, 2.0, 4.3 m/s (120, 400, and 850 fpm). The lowest, 0.61 m/s (120 fpm), represented the ventilation velocity encountered during loading by the continuous miner, while the 4.3 m/s (850 fpm) velocity represented ventilation velocity airflow over the shuttle car while tramming against ventilation airflow. Test results showed an average of the dust control efficiencies ranging from 74–83% for 0.61 m/s (120 fpm), 39–43% for 2.0 m/s (400 fpm), and 6–16% for 4.3 m/s (850 fpm). Minor modifications to the shuttle car CAC design and placement improved the dust control efficiency to 51–55% for 4.3 m/s (850 fpm) with minimal impact on dust control efficiencies for lower ventilation velocities. These laboratory tests demonstrate that the newly developed shuttle car CAC has the potential to successfully protect shuttle car operators from coal mine respirable dust overexposures. INTRODUCTION The development of the canopy air curtain (CAC) dates back to the 1970s starting with the initial development of the CAC by the Donaldson Company, Inc. under contract from the U.S. Bureau of Mines [Krisko 1975]. This CAC was originally developed for continuous miner operators when continuous mining machines had cabs. The need for a CAC on the continuous miner was eliminated when the cab was removed from the machine design. However, CAC development progressed to include CAC designs for a roof bolting machine to protect roof bolters from respirable coal mine dust [Goodman and Organiscak 2002, Listak and Beck 2012, Reed et al. 2017]. This roof bolting machine CAC research continues to the present day."

Jan 1, 2018

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By K Friese, H P÷llmann

Clinoptilolites, modified with sodium, produced a material which has been tested for the ability to remove Hg (II) from aqueous nitric acid. The amount of adsorption depends on contact time, acid concentration of aqueous solution and initial mercury concentration. The study of the kinetics of mercury uptake revealed that all sorbents exhibit a fast rate of sorption. The highest sorption capacities were observed for sodium forms, and were up to five times higher than for the unmodified zeolite. The maximum sorption capacity toward mercury is determined as 0.093 ¦g/g at an initial concentration of 10.0 ¦g/L for a clinoptilolite from Tsagaantsav deposit (Mongolia). The sorption of Hg (II) has an ion-exchange nature and consists of three stages, ie the adsorption on the surface of microcrystals, the inversion stage and the ion exchange in the interior of the microcrystal. Sorption capacity decreases with the increase of mercury concentration. The presence of other metal ions such as Cd (II), Cu (II), Ni (II) and Zn (II) increases Hg (II) uptake capacity. Finally, sorption for Hg (II) was investigated in batch systems to evaluate the short-term stability of the sorption properties.

Jan 1, 2008

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

During the first five years of operation, the Lihir gold mine has steadily increased plant throughput rate to over 4 Mtpa, well above the original design capacity of 2.8 Mtpa. Understanding how future variations in ore type impact on plant performance has been an integral part of LihirÆs development program. This paper discusses the key drivers for significant improvements to the plant, including a second oxygen plant, a pilot flotation plant, an autoclave heat recovery circuit, a pebble crushing circuit and additional autoclave feed pumping capacity. The result is a process plant with the flexibility to accommodate variations in ore type without significant loss of throughput.

Jan 1, 2003

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By Staff

"In 2014, the estimated value of total mine production of nonfuel minerals in the United States increased. The quantity of production increased for most mineral commodities mined in the United States, as did prices. Notable exceptions were the declines in prices for most precious metals. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Following the reduction in construction activity associated with the 2008- 2009 recession that continued through 2011, the construction industry continued to expand in 2014, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction. Other segments of the nonfuel minerals industries increased as well. Trends in other sectors of the domestic economy were similar to those for industrial mineral production (Table 1).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals. Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. The materials with the highest unit values, usually metals, tend to have very low production rates compared with those of many low-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the minerals industry in general, the value of production is used rather than tonnage produced. Although the value of metals and industrial minerals mined in the United States are similar, if tonnages are compared, construction aggregates dominate, dwarfing the production of all other minerals combined.Mineral industry performanceThe estimated value of nonfuel mineral raw materials, including metals and industrial minerals, produced at mines in the United States in 2014 was $77.6 billion, a 3.5-percent increase from $75 billion in 2013 (Table 2). Net exports of mineral raw materials and old scrap were $15 billion (Fig. 2). Domestic raw materials, along with domestically recycled materials, were used to process mineral materials worth $697 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $41 billion) were, in turn, consumed by downstream industries with a value added estimated to be $2,530 billion in 2014.In the United States in 2014, mine production of each of 14 mineral commodities was worth more than $1 billion. These were, in decreasing order of value, crushed stone, copper, gold, cement, construction sand and gravel, iron ore (shipped), industrial sand and gravel, molybdenum concentrates, phosphate rock, lime, salt, zinc, soda ash and clays (all types)."

Jan 1, 2014

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By David A. Summers

Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these area has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generally have been short in length, although where methane drain- age operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the Federal Government, methods have also been developed for draining seams of coal of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes.

Jan 1, 1979