Search Documents

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By M J. Noy

The automated measurement of rock fragmentation particle size distribution in the muck during muck excavation has been developing over the last 16 years. The introduction of stereo camera imaging of the muck has provided improved automated particle segmentation for image-based measurement algorithms. Recently, a new vision system processing algorithm has been developed. The inclusion of 2D texture in the analysis has provided a significant improvement in the definition of the finer size fractions, which has resulted in the automated analysis no longer requiring calibration.The previous stereo vision system algorithm required analysis calibration to account for poor ‘small particle’ definition in the 3D surface profile. This was because of the depth perception limitations of the stereo camera system at greater than 8 m. The new algorithm has been implemented on a number of shovel-installed vision systems, and the algorithm’s performance in automated analysis has been assessed against a diligent manual analysis of the same fragmentation images. The new algorithm provides improved distribution resolution and accuracy.CITATION:Noy, M J, 2015. Evaluation of a new vision system algorithm for automated fragmentation measurement from a shovel, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 721–726 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023

By Maxim Martel, Karolan Tremblay

Westwood Mine has experienced several episodes of increased seismic activity. While current geotechnical characterizations such as RMR, GSI, and Q' index can identify the general rock quality and zones at risk of convergence, they fail in identifying zones at risk of seismic activity. Previous research at Westwood Mine has shown a correlation between seismicity and areas with strong rheology contrasts. To characterize this contrast, 300 UCS tests were analyzed with their associated geochemical data, and statistical analysis and regression were performed using IOGAS software to establish a relationship between resistance and geochemistry. UCS-generated data with XRF results were transferred to Leapfrog Geo to create a block model of intact rock strength. This block model dataset was used to perform a competency contrast block model, and back-analysis of specific seismic sectors at Westwood Mine were conducted to validate the model. The purpose is to develop an established geomechanical tool capable in identifying areas with greater seismic risk associated to a change in the rock strength characteristics. By identifying those areas, mitigation measures can be implemented to minimize impact of seismicity on the operation.

Jan 1, 2023

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Tiago Ribeiro Costa

A otimização da matriz energética na produção de metais tem sido um dos tópicos predominantes mundialmente. Um dos principais consumidores ineficientes de energia, em alguns casos impactando inclusive no consumo de fornos elétricos são os sistemas de aquecimento de panelas. Buscando novas alternativas de redução de custos de energia, e redução de emissões, a White Martins encontrou uma alternativa técnica aos convencionais Pré-Aquecedores de panelas ar-gás. É o Sistema de Aquecimento de Panelas Oxicombustão com queimador Optifire, que utiliza oxigênio puro como comburente ou ar enriquecido. Comparado ao sistema ar-gás convencional, é possível promover uma economia de combustível de até 50% e redução de emissões de carbono e NOx. A tecnologia do equipamento consiste em realizar a queima estequiométrica balanceada, através da medição precisa dos gases, utilizando queimadores avançados com maior eficiência e melhorando a distribuição de calor, de forma a não gerar diferenças de temperatura entre seções. Com a tecnologia Optifire é possível inclusive o remanejamento de combustível mais nobre, como gás de coqueria em processos como aquecimento de regeneradores de altos-fornos. Este trabalho descreverá o estudo da oportunidade e dimensionamento para aquecedores de panela.

Oct 30, 2017

By M D. Griffith

Oct 12, 2022

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By А. Klemyatov, T. Vologdina, U. Gordeeva, S. Zbinets, А. Kalugin, N. Rozhdestvenskiy

The plants integrated in the PhosAgro group of companies perform processes from scientific research to the project, from ore mining to shipment of fertilisers and feed additives to consumers. An extensive process chain maintains smooth interaction at all stages from research to production. As an example, the paper shows the revamp of two beneficiation plants (ANOF-2 and ANOF-3), requiring a comprehensive approach to task solving. The intention of the revamp was to increase the total yield of apatite and nepheline concentrate, taking into account the gradual decline in the quality of ore being processed and ensuring the yield stability of final products during re-equipment of the plants. At ANOF-3, the crushing and grinding cycle was modernised, the production of nepheline concentrate was implemented, and the capacity of apatite flotation, dehydration, and drying was increased. At ANOF-2 a new process chain was implemented for the production of apatite concentrate in workshops previously used for the production of nepheline concentrate. The main building was withdrawn from operation, where ore grinding, apatite flotation and apatite concentrate thickening had been carried out. The total increase in apatite concentrate yield at two beneficiation plants was 1.3 times. A further increase in concentrate production is planned. Keywords: Apatite, nepheline, fertilisers, beneficiation, flotation, column flotation machines, revamp, fine screening

Jan 1, 2020

By A P MACONOCHIE

The methods used and some of the results obtained from a major geotechnical study of the Ok Tedi mine area, Papua New Guinea, are described. The study was carried out at both regional and local scales and extended over a two-year period. A team of individual engineers and scientists from a variety of disciplines carried out the work. This study may provide a model for other investigations in similar environments.

Jan 1, 1992

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

Jan 1, 2022

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009