Search Documents

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By J Q. Cooper

The New Zealand rail authority, Kiwi Rail and Auckland Regional Transport Authority (ARTA), are jointly planning a new mainline rail link between Auckland’s downtown Britomart Station and the existing Western Line at Mt Eden. In 2009, APB&B, a consortia of Aecom, Beca, Parsons Brinkerhoff and Hassell Architects where commissioned to develop the conceptual design, Assessment of Environmental Effects (AEE) and business case for the new 3 km rail line towards preparing a Notice of Requirement to protect the route through Auckland’s central business district.This paper describes the engineering challenges in the development of the conceptual design for the three proposed underground stations, the running tunnels and connections to the existing network. Feasible alignment and station location options were developed and evaluated using multi-criteria analysis based on key client functional requirements, constraint mapping and environmental impacts. The resulting preferred scheme was then developed to a conceptual design suffi cient for assessment of environmental effects, risks, and the development of a robust construction methodology to allow high level capital cost estimates.The paper describes some of the major challenges overcome to develop the concept, including steep gradients, narrow street envelopes with existing buildings and structures, the need for large platform spaces with low ECBF rock cover and complex connections at Britomart and the main line near Mt Eden.The development of the conceptual design of the underground stations in particular demonstrates the need for a holistic value engineering approach to satisfying the architectural and functional requirements, in a highly constrained dense urban environment and at lowest practical cost. The construction methodology was a key input to the conceptual design development throughout.The conceptual design will be used as the fundamental basis for the development of the AEE and business case for the project in the future.

Mar 8, 2011

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By G. Bulut, Ü. Yenial

"The use of recycled water in flotation has significant effects on flotation and selectivity because the recycled water contains many dissolved compounds and ions that alter the chemistry of the system. In this study, the effects of calcium, magnesium and sulfate, which are abundant components in recycled water, were investigated on galena, sphalerite and pyrite flotation using pure minerals and a complex sulfide ore by conducting bench-scale flotation, microflotation and zeta potential measurements. The bench-scale flotation tests indicated that higher recoveries of galena and sphalerite are obtained when water is recycled, due to higher concentrations of ions in recycled water. However, there was a critical ion concentration for galena recovery. The microflotation tests showed that galena recoveries at different pHs in recycled water are lower than in tap and distilled water. Pure sphalerite recoveries improved in recycled water in the bench-scale test with ore. Pure pyrite was depressed with recycled water as well. Zeta potentials became less negative with increased calcium and magnesium ion concentrations due to their adsorptions, and the presence of sulfate ions was seen to increase the negative charges of sphalerite and pyrite, conversely for galena. IntroductionWater is among the most important elements for mining and mineral processing. The distance to water sources is one of the major factors for mine site selection. The mining and mineral processing sector needs and consumes large quantities of water. In Chile in 2014, the copper mining sector alone consumed 12.7 m3/s fresh water for 1.189 tons of ore processing, and recycled 74 percent of the consumed water (Chilean Copper Commission, 2015). A plant that does not reuse or recycle any water will require 1.9 to 3.0 m3 of water per ton of ore processed (Gunson et al., 2012). Many stages of mineral processing, such as grinding, gravity concentration, dense medium separation, wet magnetic separation, flotation and hydrometallurgical operations, use large volumes of water (Schumann, Levay and Ametov, 2009).In mineral processing plants, the process water is recycled from the tailings dams, thickener overflows, and dewatering and filtration units. Wet concentration processes can require large quantities of water. Flotation, the most common process, typically takes place at 25 to 35 percent solids by mass. Most flotation plants practice at least some water reuse and recycled. Modern mines and mineral processing operations generally aim for zero water release (Levay, Smart and Skinner, 2001). In most cases, water quality has been found to affect flotation performance, and this interaction remains under investigation."

Jan 1, 2016

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

By Walter W. Kaufman

This Bureau of Mines manual for design of surface mine haulage roads covers such aspects of haulage road design as road alinement (both vertical and horizontal), construction materials, cross slope, and drainage provisions. Traffic control and design of proper lane widths to promote safe vehicle movement are included, as are suggested criteria for road and vehicle maintenance and for runaway-vehicle safety provisions. The aim of this publication is to provide those involved with surface mine haulage road design with a complete manual of recommended practices that, if implemented, will promote safer, more efficient haulage routes.

Jan 1, 1977

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By C A Heinrich, Jaques A. L, L A I Wyborn

Most orebodies have cross-sections of less than I km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defmed as 'all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated form and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system offluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: I. sources ofthe mineralising fluids and transporting ligands; 2. sources ofthe metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common through

Jan 1, 1994

By T. H. Peters

The historical development of this program, dating from the construction of Nickel Park at Copper Cliff in 1917 to the various current projects carried out in the Ontario Division's program, is reviewed. Practices used to grow vegetation on stressed areas, the beneficial aspect of the improved aesthetic appearance of company properties from the point of view of public relations and the improved approach to the workplace by the employee are discussed. The revegetation of the tailings area and its gradual transformation into a Wildlife Management Area is reviewed.

Jan 1, 1978

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By Vince Luongo

"INTRODUCTIONThe West Side Combined Sewer Overflow (CSO) Tunnel Project is located in Portland, Oregon and is part of the Willamette River CSO Control Project. The purpose of the West Side CSO Project is to reduce the frequency and volume of combined sewage overflows from the drainage areas on the west side of the Willamette River using the West Side CSO tunnel as a combined storage and conveyance facility. The sewage is then directed to the Pump Station on Swan Island, which is located on the east side of the Willamette River. From here the combined sewage is pumped through force mains that discharge into the existing Peninsular and Portsmouth tunnels.The West Side CSO tunnel has an inside diameter of 14-feet (4.27m) and is approximately 18,150-feet (5,532m) long. The tunnel slopes at a constant down gradient of 0.0018 from south to north over the entire length of its alignment.The tunnel passes beneath six existing bridges; Hawthorne Bridge, Morrison Bridge, Burnside Bridge, Steel Bridge, Broadway Bridge and Fremont Bridge. The general tunnel alignment follows beneath the Naito Parkway starting at Clay Street Shaft and connecting three other shafts on the west side of the Willamette River, Ankeny Shaft, Upshur Shaft and Nicolai Shaft. It then passes below the Willamette River and on to Swan Island to connect with the Confluent Shaft, which will combine flows from the West Side CSO and East Side CSO (not part of this contract) and then continues to the Pump Station Shaft.The Nicolai Shaft is the primary mining shaft from which two TBM’s were launched to construct the West Side CSO tunnel. The first TBM started mining south and terminated at the Clay Street Shaft. The second TBM started mining north below the Willamette River and terminated at the Swan Island Pump Station Shaft."

Jan 1, 2006

By B. Andersen

An accurate knowledge of Interactions among mineral particles and between such particles and dissolved and precipitated species Is Important in developing efficient separation processes. In this investigation interactions in Florida phosphatic clay waste, that are relevant to dispersion and selective reagent adsorption, the two main prerequisites for selective flocculation, were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slime were due to unselective polyacryllc acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Ai and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. Further increase in separation of natural slime is likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1992

By I. B. Scorzelli

The aim of this paper is to make a detailed mineralogical characterization of a typical brazilian xenotime and zircon from the Pitinga Mine using SEMIEDS techniques, On the other hand, superficial pretreatments with HCI, HN03 and HF were done to evaluate the modifications on surface compositions and the morphology of the particles for flotation purposes, The studies showed that both xenotime and zircon present very small inclusions of thorite; zircon is strongly metamictizated given rise to malacon. The HF pretreatment deeply affected the morphology of the particles as well as the surface properties in relation to flotation.

Jan 1, 1996

By J. James Eidel

Geological interpretations generally require projections from direct observations at the earth's surface. Crustal projections include mineral deposits as well as the geochemistry of the crust and its fluids, structure and tectonics. Drilling offers opportunities for verification of the required projections, and is thus a required step in furthering crustal understanding. Like any new science, the direct observations that drilling provides commonly generate major surprises and stimulate totally new ideas. Drilling is costly. There are many critically important scientific problems with societal and potential economic benefits in mineral deposits which have not been drilled because the holes are difficult to justify as economically sound risks for private capital. Such holes, however, are highly justifiable research goals for government because of the significant new opportunity for ore deposit insight and exploration that they afford. The earth science community is prepared with excellent drilling projects for research in mineral deposits.

Jan 1, 1985

By C. Meyer, J. J. Eidel

Major gaps in understanding hydro- thermal systems remain after a century of studying fossil ore deposits and active geothermal areas. The periodically rejuvenated concept of "stacking" ore deposit types has never been verified by a continuous sample. Basal and marginal regions of both “fossil" and "active" hydrothermal systems normally lie beyond the limits of economic exploration, remaining inadequately exposed. Incomplete scientific under- standing of he vertical transitions clearly limits the efficacy of exploration programs for hydrothermal ores of all types. The Continental Scientific Drilling Committee's (CSDC) Panel on Mineral Resources has defined dedicated research objectives and add-on experiments to industry or government drill holes of opportunity.

Jan 1, 1988

By Michael Arnold, Jignyash Manyam, Yoav Rappaport

The USACE required construction of over 13 miles of cutoff wall at an average depth of 65 feet for the Herbert Hoover Dike (HHD). To meet project requirements, to provide quality control and make sound operational decisions, automated data capture, retention and visualization is crucial. Accurate and complete data management allows the authors to deliver critical business insights and to improve operational efficiencies. The author’s understood the necessity of capturing all their data, and efficiently processing and displaying it for multiple stake holders, for both internal and external purposes. The authors realized early in the project life cycle that data ownership and management is one of the fundamental features of the construction process. The authors developed their own software and use two in house applications; WEB-BGM online portal and, b-project which store rig production information combined with field quality control. b-project is used to create and deliver the Enterprise Database (EDB) to the USACE. Another biproduct of capturing the production data is the generation of the Geographic Information Systems (GIS) and also business analytics visual interactive display, developed through Microsoft Power BI. The paper focuses on the business process workflow and various technologies employed and lessons learned from the field operator perspective to achieve higher returns on business software operations.

Oct 1, 2022