Search Documents

Traditional loading systems have relied for many years on wheel and track loaders, power shovels, conveyor belts, and more recently, hydraulic front shovels. Each has certain advantages and disadvantages, depending largely on job conditions. Hydraulic backhoes were introduced several years ago as still another truck loading option. At first, buckets were small and backhoe use was limited to small earthmoving projects. Now, as backhoes are equipped with shorter sticks and bigger buckets to move larger quantities of earth. The "mass excavation" concept offers an excellent truck loading option in many situations. System Development and Advantages Mass excavation was first used successfully by contractors in site development and highway construction, loading both on-highway and off-highway trucks. Operators were able to take advantage of the excavator's ability to work in poor underfoot conditions and dig in tough materials. The technique was first applied to mining in the kaolin mines of central Georgia. Kaolin, one of the world's most abundant minerals, is used to make paper, paint, ceramics, rubber, plastics, and many other products. Since kaolin clay is slippery when wet, load-out with wheel loaders is very inefficient. Also, kaolin is found in very spotty deposits due to the weathering process involved in its formation. Consequently, draglines are also impractical for kaolin mining since they don't have the mobility to move between clay deposits. In response to these mining conditions and kaolin characteristics, mines began using excavators in mass excavation as early as 1976. They have developed a system that takes advantage of the excavator's •high penetration and breakout force in tight materials; •fast-cycling hydraulics; •ability to work in poor underfoot conditions; and •mobility in comparison to draglines. This loading method has been successful in Georgia's kaolin mines and now can be applied to other mining operations as well. The excavator's ability to carefully dig spotty ore deposits is an asset at uranium mining operations. Any mine can take ad-

Jan 3, 1982

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

Pyrite Bioleaching and Slag Neutralisation - Two Treatments in a Single Process for Recovering Valuable Metals from Both Materials Very often the production of copper sulfide concentrate yields pyrite concentrate as a by-product. This is the case at the Knre mine in northern Turkey. This kind of concentrate may contain low grades of valuable non-ferrous metals. Bioleaching of such pyrite concentrates is a processing technique to solubilise metals like copper, zinc or cobalt in a sulfuric acid pregnant solution. The pyrometallurgical processing of copper sulfide concentrate produces slag that still contains valuable metals in varying concentrations. Slag is used in many ways: as aggregates, ballast, pavement material, in cement production and glass making. Due to its relatively alkaline nature, it can also be used to neutralise acidic solutions. A preliminary study of the bioleaching of the pyrite concentrate (Co 0.28 per cent, Cu 0.56 per cent and sulfur as sulfide 42.6 per cent) produced at Knre has been undertaken with the assessment of the neutralisation of the acidic bioleach solution by using old slag (Co 0.29 per cent, Cu 1.70 per cent and sulfur as sulfide 0.89 per cent) stockpiled on the site. The main conclusions of the study were as follows: Knre pyrite was amenable to bioleaching at 40¦C. Cobalt solubilisation directly related to pyrite degradation reached a maximum yield above 90 per cent. Final copper recovery was limited to approximately 66 per cent not directly related to bacterial growth and pyrite oxidation. Slag could be used as a substitute for limestone as a neutralising agent in the bioleaching tanks. Cobalt and copper could be recovered from pyrite concentrate and slag simultaneously from both materials. A pre-feasibility study is underway to carry out a preliminary cost estimate of an installation for cobalt and copper production from these two materials processed in a single operation.

Sep 13, 2010

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Ken Wood

"A reliable source of water of an acceptable quality is vital to the success of any mineral processing plant using wet methods. For Cerro Verde, a new 108,000 t/d copper mill in southern Peru, the main source of raw water is the Chili River. The Chili River is heavily contaminated with raw sewage, industrial wastewater and agricultural runoff, and can also receive high sediment loads during the rainy season. The initial water treatment plant could not supply design flows of water due to the exceptionally poor water quality. Problems with treated water quality caused significant difficulties with water consuming equipment, such as the plant cooling systems. This paper details the Cerro Verde water system and changes from design through to start up from a mineral processing perspective.INTRODUCTIONMining, and mineral processing in particular, is a water intensive activity. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry. This case study forms a basis for ongoing research into water use and reuse at mines and mineral process plants, conducted by AJ Gunson, under the supervision of Dr. Bern Klein and Dr. Marcello Veiga at the University of British Columbia. The case study material was gathered through involvement with the design, startup, and redesign of the Cerro Verde water system.Cerro Verde is a low-grade copper porphyry mine, located near the city of Arequipa in southern Peru, at an elevation approaching 2,800 m. In 1972, one of the world’s first copper Solvent Extraction – Electrowinning (SX/EW) facilities was built on the site, processing oxide ore from two main open pits. In 2004, the operator, Sociedad Minera Cerro Verde S.A.A. (SMCV), approved a 108,000 t/d expansion project to process sulfide ore reserves through a new concentrator plant. The plant was designed under extremely tight schedule and capital constraints, with a mandate to intentionally avoid any overdesign."

Jan 1, 2008

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Sachihiko Tokunaga, Hirofumi Taguchi, Kenji Maruyama, Hidenori Takahashi, Yoshiyuki Morikawa

"Abstract The present study proposed a new liquefaction countermeasure to improve sandy ground and conducted a trial execution. The new method is a floating-type and lattice-shaped cement treatment method, where cement-treated soil is not fixed to a non-liquefiable stratum. A fixed structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were first conducted to confirm the mechanism of the new method. Then, a series of centrifuge model tests were performed to demonstrate the effect under a stress condition at the prototype scale. The analyses and model tests confirmed the effect of the liquefaction countermeasure. Finally, trial executions were carried out to confirm high-quality vertical execution.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. In particular, the cost of the high-pressure jet mixing method, which can be applied to the liquefiable ground under existing structures, is significantly high. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2014

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Dominic Fragomeni, Tony DiFeo, Martyn P. Hay

"As part of an investigation into flotation modelling of industrial scale operations, Falconbridge Ltd organised a “blind” test of the SUPASIM flotation model developed by Eurus Mineral Consultants (EMC). Two sets of rougher rate data, a flowsheet and the number and size of cells in the rougher bank were supplied from a plant that had been previously surveyed in November 2003. The name of the plant, cleaner circuit details and circuit mass balance were, at the time, unknown to EMC. With only these data, flotation performance was simulated and the cleaner circuit sizedFalconbridge then compared predicted and actual float performance and mass balance and found that final concentrate recovery and mass and circuit cell volume matched closely. Simulated recoveries relative to actual were +0.4% Cu, +0.1% Ni and -0.7% Co. However, prediction of metal distribution in the internal streams making up the various circulating loads showed some sizeable errors. On this initial success, the trial was extended and additional float test data for rougher feed, cleaner feed and cleaner scavenger feed was generated on site in April 2005. Further simulations significantly improved prediction accuracy for metal distribution in the internal streams. The average difference between predicted and actual recovery for all streams was reduced from 10.5% to 0.4%. This updated simulation was then used to ascertain the impact on final recovery, grade and plant circulating loads of increasing feed tonnage from 114 to 150t/hr. A number of scenarios were simulated in order to understand the contribution that (a) the fast and slow floating fractions and (b) regrinding of cleaner tailings are making to overall plant recovery.Simulation was then used to determine how much the flotation kinetics of both rougher feed and cleaner scavenger feed have to increase in order to deliver a 1.5% improvement in overall plant recovery. These improved kinetic values provide a target for laboratory testwork and operating conditions can be varied to determine how best to achieve these new values of fraction and rate."

Jan 1, 2006

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By Colin Lindsay

"The Collahuasi copper mine, located at an altitude of 4300 meters above sea level in northern Chile, commenced operations late in 1998. The mine is currently the 4‘h largest copper producer in the world and comprises an open pit, a 60,000 tpd sulphide concentrator, a 15,000 tpd oxide heap leach and SWEW plant and a 200 km concentrate pipeline to a port facility.Constructing, commissioning and operating a mine at high altitude presents unique challenges in terms of the performance of both equipment and people. It is important that these be recognized and carefully considered during the feasibility study and the detailed design stages and the success of the Collahuasi project is largely due to this. The plant design incorporates a number of features aimed at mitigating the problems of altitude and the construction methodology also took into account the particular site conditions.This paper discusses the Collahuasi project team’s approach to planning for the remote location and also some of the problems experienced during construction, commissioning and operation.INTRODUCTIONThe Collahuasi mine is located in northern Chile, some 250 km to the south-east of the port of Iquique and 15 km from the Bolivian border. The mine facilities lie between 3800-4300 m above sea level on the Altiplano, the central plateau of the Andes mountains, and cover a total of approximately 95,000 hectares. Although the area is arid, it experiences an average of 150 mm of precipitation annually and weather conditions can be extreme. Temperatures during the day range between -3 to +11 º C and are generally below 0ºC at night, sometimes as low as -20°C. High energy winds are common and humidity is low. Much of the precipitation occurs during the winter as snow but there also occurs a period during the Chilean summer known as the “Invierno Boliviano’’ (or Bolivian Winter) which is characterized by severe electrical storms and rain."

Jan 1, 2001

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924