Search Documents

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By M. Hesham El Naggar, Tony Sangiuliano, Alper Turan

"Bridge abutments supported on pile foundations are often constructed over weak and compressible soils. The consolidation settlements induced by the embankment loads are known to result in downdrag and lateral forces on the piles supporting the bridge abutments. The performance of a pile group including inclined piles embedded in consolidating soils was investigated numerically considering surcharge loads from approach embankment construction. A two-dimensional numerical model was constructed using commercial finite element software PLAXIS and calibrated against field measurements of the abutment movements observed on Brookdale Avenue Underpass Structure located on the Macdonald-Cartier Freeway in Ontario between Cornwall and the Quebec border. The soft soil model (SSM) was used to simulate the constitutive behavior of the compressible soil deposit. The SSM model parameters were determined based on the laboratory tests. Subsequently, time dependant development of downdrag effects was comparatively evaluated for vertical and inclined single piles as well as a pile group that included both vertical and inclined piles.Results showed that drag loads increased with the consolidation time. However, majority of accumulation of drag loads took place within first 120 days after installation of piles. The results also indicated that the shear forces and bending moments are controlled by the lateral spreading of foundation soil and their accumulation is proportional to consolidation time. The large axial strains caused by large downdrag forces are considered to have yielded the piles and this is a possible reason for unusual abutment movements. The results presented in this study are considered to be of interest to researchers and practitioners.1. IntroductionDeep foundation units are widely used for supporting bridge piers and abutments, where weaker surficial soils preclude shallow foundations. Particularly in Ontario, semi-integral and integral abutment bridges are typically supported on end-bearing steel driven piles. The construction of approach embankments over weaker, compressible soils results in significant vertical and lateral soil movements, which induce additional loads on piles supporting the abutments. In order to minimize such effects, preloading and surcharging are commonly employed approaches to avoid unanticipated settlements prior to the installation of piles. Other alternatives such as aggregate pier supported approach embankment are also being studied as the schedule restrictions imposed by preloading and surcharging becomes cost prohibitive (Turan et al. 2012)."

Jan 1, 2015

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By C. S. ROBINSON, T. M. Romslo

This investigation was conducted jointly by the Bureau of Mines and the Geological Survey to obtain further information on the source and economic possibilities of the copper mineralization exposed on the Copper Giant group of claims, Ajo mining district, Pima County, Ariz. The Copper Giant group of claims was first brought to the attention of the Bureau of Mines by Joseph Hunter (deceased), Phoenix, Ariz., part owner of the claims. In December 1942 these claims, and an adjoining group, were investigated by T. C. Denton, mining engineer, formerly with the Bureau of Mines, and Nels P. Peterson, geologist, Federal Geological Survey. It was concluded the area could not be considered as a source of copper for immed- iate emergency needs and that further investigation of the area, at the time, was not warranted. In the spring of 1948 the lessee, J. H. Greenway Albert, requested Bureau of Mines assistance in developing the property. J. H. Hedges, former chief, Tucson Branch, Mining Division, and Lincoln A. Stewart, mining engineer, Bureau of Mines, made a cursory examination of the property and noted that at numerous places, low-grade copper mineralization appeared on fractures and bedding of the Locomotive fanglomerate and Ajo volcanics, which are thought to be of Tertiary age. During the period of May 11 through 14, 1949, Bureau of Mines engineers3 mapped and sampled two areas of mineral- ization. On June 2 and 3, 1949, the areas selected by the Bureau and three other nearby mineralized areas were investigated by C. A. Anderson and R. S. Cannon, Jr., of the Federal Geological Survey. As a result of these examina- tions, further investigation of certain areas was believed to be merited. The Copper Giant area was selected as the most favorable in which to carry out exploratory and development work. The field work on the project was started in October 1949 and completed in December 1949. It consisted of road building, trenching, sampling, topo- graphic and geologic mapping, diamond drilling, and logging of core. Samples taken on the project and during preliminary examinations totaled 64, of which 63 were surface samples. Diamond drilling, started October 10 and completed December 7, consisted of two holes for a total depth of 1,542 feet.

Mar 1, 1952

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By Kevin P. Gleckler, Steven C. Highfill

"Escalators to access platforms for the Second Avenue Subway Station at 72nd Street in Manhattan are to be installed in the basement of an existing 19-Story residential building. The escalators, which extend below the existing building foundations, require excavation of an inclined rock cavern up to 80-feet deep. Underpinning of columns within the 19-story building as well as a stone masonry party wall and columns for an adjacent 5-story building was completed prior to excavation of the rock cavern to ensure structural stability.This paper will discuss the analysis and design of the underpinning system, the installation and load transfer procedures and the cavern excavation immediately below. The underpinning system was subject to very strict deformation limits and to electronic monitoring prior to and throughout the load transfer and construction process. Key details such as the load transfer mechanism between the reinforced concrete column and the temporary structural steel underpinning frame will be discussed. The challenging rock excavation process will be described which utilized conventional equipment and pattern drilling with Damite rock splitting mortar.INTRODUCTIONPhase 1 of the Second Avenue Subway is being built by MTA Capital Construction (MTACC) to improve subway service on the east side of Manhattan. Entrance 1 for the 72nd Street Station of the Second Avenue Subway is located on the east side of 2nd Avenue at the corner of E 69th Street in New York City. Access to the station mezzanine, approximately 80-feet below grade, is designed to be routed through the basement of an existing 19-story residential building. From the sidewalk, stairs and escalators within the width of sidewalk connect the riding public to a basement level mezzanine, which turns into the building at roughly 16 feet below grade (Fig. 1). Riders then connect to three long escalators to arrive at the station mezzanine. The escalators are to be installed within an inclined and arched cast-in-place (CIP) concrete lined rock cavern (Fig. 2). Construction of both the entrance into the basement and the escalator cavern require the transfer of columns within the 19-story building. Excavation of the escalator cavern also impacts the foundation support for columns and a load bearing party wall for the 5-story residential building immediately to the north. Two stages of load transfer were used at each location. The Stage 1 transfer used a temporary underpinning system to unload the current structure which allowed for construction of the permanent transfer girders. Stage 2 transferred the load from the temporary system to the permanent transfer girders."

Jan 1, 2016

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020

By C. van Buuren, R. F. Sandenbergh, P. J. Pieterse

Gold extraction from double refractory ores using conventional cyanidation has proved challenging due to the presence of carbon within the ore. Carbon particles may adsorb leached gold resulting in gold losses to tailings, i.e. preg-robbing the gold. Some of the preg-robbed gold may be recovered by the application of the HiTeCC process on CIL tailings. The process developed by Metso Outotec involves caustic conditioning of the tailings followed by high temperature desorption and simultaneous adsorption onto virgin activated carbon of the aurodicyanide. The aim of this paper was to develop a model for the HiTeCC process which could be used to support design and optimisation of the process, based on the adsorption characteristics of the preg-robbing and activated carbons. It was found that accurate experimental isotherms can be used to predict the behaviour of preg-robbing adsorbents. Comparing the sorption isotherms for preg-robbing ores and activated carbon indicated similar dependencies on temperature and ionic composition. Applying boundary layer diffusion models coupled with experimentally determined isotherms for preg-robbing ore and activated carbon, the HiTeCC process was successfully simulated at experimental and plant scale. Gold recovery of the HiTeCC process is most sensitive to the temperature of desorption and gold loading of the activated carbon, with increased temperature improving recovery. The gold loading of the activated carbon in the process should always be maintained lower than that of the normalised pregrobbing carbon gold loading to ensure favourable conditions for adsorption onto the activated carbon. Caustic conditioning stabilises adsorption and is therefore not necessary during the desorption stages of the process, but potentially improves recovery during adsorption. Keywords: Preg-robbing, refractory gold ores, HiTeCC, aurodicyanide

Jan 1, 2020

By Rodrigo Peroni, Vitor Campos

Carajás is one of the largest open pit mines in the world. The mine is comprised by a haul road network more than 100 km long, where the need for good roads is paramount and determining of the truck performances. This work integrates, regarding the ultimate pit design, an approach to consider an economic value to an originally unfit material, assuming it has the appropriate characteristics for haul road construction, which sometimes lies over economic iron ore. This measure demonstrated an improvement in the utilization of resources and guarantee the necessary material to the haul road design and Mining Pads maintenance.

Jun 25, 2023

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By M. Wrobel, J. Hammerschmidt, M. Runkel

Fluid-bed technology is a key pyrometallurgical step for processing a vast number of ores and concentrates. Over the past 50 years, considerable research and development efforts have been made by Metso Outotec to expand the application window of this technology. This paper illustrates different processing routes where fluid-bed technology plays an important role in the production of the copper. The fluid-bed processes utilized are partial, sulfate-producing, and dead roasting. The focus of this paper considers the advantages of the dead-roasting process. This “zero waste” process can provide copper oxides, steam, electrical power, and sulfuric acid for new and existing solvent extraction–electrowinning plants. In a case where an operation is running out of oxidic ores and concentrates, fluid-bed roasting can be applied to close this gap and provide the required copper oxides in a sustainable way.

Jan 1, 2023

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021