Search Documents

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By S. C. Flood, J. D. Hunt

"The columnar-equiaxed transition (CET) has been studied numerically under unsteady-state conditions using mathematical models that: (i) include a non-equilibrium undercooling at the columnar front;and(ii) describe the simultaneous evolution of the columnar and equiaxed zones.The results are discussed and compared with those produced by a steady-state analysis.IntroductionThe majority of the previous work on the columnar-equiaxed transition (CET) has concentrated on the production of equiaxed nuclei, regarding this as being the critical step in the formation of an equiaxed zone. Recently, the growth of equiaxed grains has been considered and this is not unreasonable because, for an equiaxed zone to be present, the grains must grow as well as nucleate. Since the growth rate of the grains will be determined by the thermal environment at and ahead of the columnar tips, it was decided to model the liberation and flow of heat during solidification to discover whether the various trends in the columnar range might be explained by their effect on the temperature profile throughout the casting. The models presented here for the solidification of a casting are the first to include the latent heat liberated ahead of the columnar front. Burden and Hunt (1) consider its effect only qualitatively, and although Lipton et al (2) adopt a criterion for the CET which is based on the thermal interaction of the columnar and equiaxed grains, they do not actually include the latent heat in their calculations.It can be argued that the latent heat liberated by the equiaxed grains in the bulk will retard the columnar dendrites in a casting: once the equiaxed grains are sufficiently well-established, the latent heat that they evolve could slow down the columnar growth to such an extent that the equi axed would dominate. Alternatively, the latent heat produced by the equiaxed grains might suppress further equiaxed solidification by raising the bulk temperature. The nature of the thermal interaction between columnar and equiaxed growth is not obvious, and because it is dependent on the material parameters and the dimensions of the system, it cannot be considered effectively in a qualitative way but has to be studied quantitatively: hence the need for the mathematical models discussed in the following pages. The results of the models are discussed in the light of a steady state analysis."

Jan 1, 1986

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By P. Burke, V. Vuaroqueaux, A. Doyle, C. Petit, Kipouros. G. J.

Magnesium and its alloys are attractive for use in automotive and aerospace applications because of their low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present work reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents results of current work on producing magnesium alloys via powder metallurgy (P/M). P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The surface layer formed on the Mg powders during processing acts as a barrier to diffusion and sintering is problematic. The layer contains oxides, hydroxides and carbonates of magnesium, formed by reactions with the atmosphere. There are several means to possibly overcome this barrier. Alloying additions have been identified that may promote surface layer disruption during sintering. Processing variables such as sintering atmosphere may reduce the layer or allow the formation of less detrimental compounds. Post-sintering processes such as hot working may disrupt the layer and improve density. The experimental effect of all these processing parameters is presented in this paper.

Jan 1, 2010

By David Stone

The Beal Mountain Mine near Anaconda, MT is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of about 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges.

May 1, 2001

By Leonard J. Friedman

Modern smelting systems using continuous, flash and/or oxygen smelting processes have a significant effect on the choice of sulfur dioxide control processes and system arrangements. Based on gases from an enriched air or oxygen smelting furnace and copper converters the paper reviews and analyzes alternate processes and system arrangements for recovery of sulfur dioxide. The work indicates the choice system to include a conventional sulfuric acid plant for converter gas and a liquid SO2 plant to handle the high strength smelting fur¬nace gas. The liquid SO2 plant would be used as a fly-wheel to damper the flow and SO2 concentration variations of the con-verter acid plant. Potential energy recovery alternates and product flexibility are also reviewed.

Jan 1, 1983

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Jorge MRS Relvas

Recent research both on active and fossil systems has demonstrated that shallow subseafloor replacement processes are not only viable depositional mechanisms for massive sulfide mineralization, but likely contributed as a major component of the mineralization occurring in large VHMS deposits and in many present-day seafloor hydrothermal systems. In the giant Neves Corvo deposit, as in many others VHMS deposits of the Iberian Pyrite Belt, there is overwhelming evidence for silicate-sulfide replacement processes being largely responsible for the efficiency of the ore-forming systems and huge size of the deposits. Textural evidences at all scales, coupled with a well-constrained mass-balance geochemical analysis, indicate that extensive replacement in the lavadominated volcanic rocks of the footwall sequence, and disseminated replacement mineralization in the volcaniclastic and/or sedimentary units were major mechanisms of ore formation in the Neves Corvo deposit. Shallow metal deposition prior to fluid discharge on the seafloor is likely to play a major role in seafloor massive sulfide mineralization. This premise should be envisaged as critical in evaluating the economic potential of seafloor resources, and should certainly be part of the equation when plans for seafloor mineral exploration missions are drawn.

Sep 14, 2011

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements provide evidence for the formation of Cr(V) intermediates in the enzymatic reduction of Cr(VI) by glutathione reductase (GSSG-R) in the presence of NADPH, indicating an initial single-electron transfer step in the reduction mechanism. Depending on the pH, at least two different Cr(V) species are generated which are relatively long-lived. In addition, we have detected the hydroxyl (·OH) radical formation during the GSSG-R catalyzed reduction of Cr(VI) by spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) and a-(4-pyridyl-1-oxide)-N-tert-butylnitrone (4-POBN) as spin traps. Superoxide dismutase (SOD) causes only a minor effect on the ·OH radical and Cr(V) formation, indicating that the ~ - is not significantly involved in the reaction mechanism. Catalase enhances the Cr(V) formation and substantially inhibits the ·OH radical formation, indicating the involvement of hydrogen peroxide (H20 2) in the reaction mechanism. Addition of H20i suppresses Cr(V) and enhances the ·OH radical fonnation. Measurements involving N-ethylmaleimide show that the Cr(V) species, produced enzymatically by the reduction of Cr(VI) by GSSG-R, react with H2O2 to generate ·OH radicals, which might participate in the initiation of Cr(VI) carcinogenicity.INTRODUCTIONC(VI) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals [1-4) and to cause mutations in bacteria and transformation of mammalian cells [5-8). In contrast, most Cr(lll) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic [9, 10]. Cr(VI) and Cr(lll) oxidation states are different in their metabolic pathways: Cr(VI) ions are rapidly transported across cellular membranes [2, 11-13), while Cr(lll) moieties do not easily penetrate cells and are not oxidized by cellular constituents [3]. Since it is known that the reduction of Cr(Vl) is required for its reaction with DNA [2], the molecular mechanisms for the intracellular Cr(VI) reduction have been the focus of studies during the past decade but the details are still not understood."

Jan 1, 1990

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By W. L. Eaton

This report is the second in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Wyoming Basin of the Northern anthracite field is presented. The first report I.C. 8274, published in 1965, was a catalog of microfilmed maps of mines in the Eastern Middle anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1968

By Zhengdong Liu, Kaizhong Zhang, Zhaonan Jiang, Yuanping Cheng, Biao Hu, Qingquan Liu, Ranpeng Wang

"Major coal mining areas in eastern China have entered into the deep mining state. Gas pre-drainage, which has been successful at shallower depths, is not suitable at greater depths because of complex conditions. Coal permeability, which is closely related to the damage behavior of coal, is the most important parameter in determining gas migration and gas drainage in a coal seam. To achieve an optimal gas drainage design in a deep mining state, the damage and permeability evolutions of coal should be further studied. The progressive failure process of coal has been analyzed by conducting a series of triaxial loading and unloading tests. The development of coal fractures has been successfully quantified, and the corresponding characteristic stress points have been obtained by using Martin’s fracture model and the stress-strain curve. Coal will produce plastic deformation, and its permeability will rapidly increase when the stress level reaches damage expansion stress. INTRODUCTION Coal mine methane (CMM) is a general term for all methane released during and after mining operations. CMM is both a potentially valuable energy and a serious hazard in active coal mines. Degassing coal seams is important for mitigating this hazard and results in the beneficial recovery of a cleanburning, low-carbon fuel resource (Karacan, Ruiz, Cotè, and Phipps, 2011). The permeability of coal is a key parameter in determining CMM production, coalbed methane (CBM) production, CO2-enhanced coalbed methane (CO2-ECBM) production, and CO2 storage in coal seam reservoirs (Connell, Lu, and Pan, 2010; Chen et al., 2011; Perera, Ranjith, and Choi, 2013). Significant research has been condcuted to the study of the evolution of coal permeability. These studies revealed that coal permeability evolution is controlled by the competing influences of effective stress and sorption-induced coal deformation. Chen et al. (2011) investigated the influence of an effective stress coefficient and sorption-induced strain on the evolution of coal permeability. Robertson and his team (Robertson, 2005; Robertson and Christiansen, 2005) measured sorption-induced matrix strain and permeability changes with regard to CO2, CH4, and N2. They found that the compressibility is not constant in a natural coal sample. Karacan (2007) conducted a series of experimental tests to study the swelling-induced volumetric strains internal to a stressed coal associated with CO2 sorption. Liu et al. (2016) investigated the effects of matrix swelling area propagation on the permeability evolution by using both natural and reconstituted samples. Many coal permeability models have been developed to describe the permeability evolution under uniaxial loading, biaxial strain, hydrostatic confining pressure, triaxial strain, and triaxial stress. Recently, some analytical permeability models have been developed to describe the anisotropic permeability behavior (Palmer, 2009; Pan and Connell, 2011; Robertson and Christiansen, 2005; Wang, Zang, Wang, and Zhou, 2014; Chen, Pan, Liu, and Connell, 2012)."

Jan 1, 2017

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrates identified gold to be mainly present in the form of a solid solution in pyrite. Gold distribution resulted in a poor extraction yield of 55 % by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction and has led to a gold extraction yield of 94%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and used a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a diaphragm-less electrolysis cell. The extracted gold was recovered via adsorption over silica and the gold depleted brine was treated for impurities removal. This brine was recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Jan 1, 2014