Search Documents

By R. M. Zimmerman

INTRODUCTION Tuff is being considered as a possible geologic median for the underground storage of commercial high level radioactive wastes by the Department of Energy (DOE). DOE has the responsibility for developing or improving the technology fir safely and permanently isolating these wastes. DOE programs must satisfy requirements established by the Nuclear Regulatory Commission (NRC) for the licensing and regulating of these storage facilities (NRC 1981). Pertinent draft NRC requirements are: 1) releases of radioactivity to the environment must be within prescribed limits and 2) emplaced canisters containing wastes must be retrievable up to 50 years following emplacement. High level radioactive wastes produce heat in storage and it is essential that the thermal/mechanical/hydrological response of the host rock will not significantly degrade either the structural performance o£ the repository or the ability of the natural or engineered barriers to retard radionuclide migration. The Nevada Nuclear Waste Storage Investigations (NNWSI) was established by DOE to evaluate the suitability of disposing of high level nuclear wastes on or near the Nevada Test Site (NTS) (NNWSI 1980). NNWSI has focused exploration and site evaluation on the tuffs of Yucca Mountain. Field testing is essential to support site characterization and repository design efforts. Preliminary studies have been conducted indicating that tuffs in G-tunnel on the NIS contain welded and nonwelded tuffs that have similar properties to those in Yucca Mountain. Thus, field testing can be accelerated. This paper discusses the issues supporting the planned field experiments in G-tunnel. Issues not related to rock mechanics are not included.

Jan 1, 1982

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By R. Michael Digman

Few efforts have been undertaken to date to assess the quality of mandated coal mine health and safety training for new miners and for experienced miners. This study was concerned with the quality and effectiveness of existing classroom health and safety training programs. The study involved field data collection through pre- and posttesting of trainees, audio-taping class sessions, and administering short feedback forms with trainers and trainees at 14 sites in West Virginia, Maryland, Kentucky, and Pennsylvania. Results indicate that goals, methods, materials, and outcomes of existing training programs vary widely among trainers and sites. The report provides less by way of solution to problems, than it highlights the breadth of issues that relate to the question of training effectiveness and quality. The report concludes that additional work by industry, labor, government, and academia is necessary in order to improve health and safety training programs. Recommended steps are: (a) to develop performance standards and measurable criteria in each of the types of mandated training, (b) to develop better training of trainers, (c) to develop expanded training support services. and (d) to undertake further research and development in health and safety training in the mining industry

Jan 1, 1982

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By Lawrence W. Teufel

An anelastic strain recovery technique is presented as a method of determining the directions and ratio of the maximum and minimum horizontal in-situ stresses from oriented cores from deep wells. Predictions of hydraulic fracture azimuth inferred from principal stress directions determined from both elastic and time-dependent (anelastic) strain relaxation measurements of volcanic tuff are consistent with the observed orientations of hydraulic fractures produced in simulation and mineback experiments, underground at the Nevada Test Site. In addition, anelastic strain recovery measurements on oriented cores of shale and sandstone from well depths of about 1680 meters show consistent relaxation directions of the principal horizontal strains and have enabled a prediction of the principal horizontal stress directions and hydraulic fracture azimuth.

Jan 1, 1982

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By M. N. Rubin

This report summarizes the work performed under USBM contract J0100018. The purpose of this work was to document the currently available noise control techniques that can be incorporated into new coal preparation plants during the design stage. This was accomplished by reviewing the related experience of the contractor and subcontractor (Bolt Beranek and Newman Inc.), conducting an extensive literature search, visiting operating coal preparation plants, and contacting various equipment manufacturers. The treatments addressed include equipment substitution, changes in plant layout, and retrofit treatments for existing equipment.

Jan 1, 1982

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By Frank G. Horino, V. E. Hooker

INTRODUCTION The determination and use of mechanical properties of rock in engineering and rock mechanics are rapidly developing. Many of these properties are determined on intact rock specimens; thus, their application and repre¬sentation of rock mass properties may be limited. How¬ever, relative information often provides useful guidance in the solution to mine design and stability problems. Summarized in this chapter are some of the stan¬dardized techniques and procedures currently used to obtain these mechanical properties. Typical applications of the use of these properties are also presented. Stan¬dardized techniques include those advanced by the American Society of Testing and Materials (ASTM), International Society of Rock Mechanics (ISRM), US Bureau of Mines (USBM), Canadian Dept. of Mines and Technical Surveys, South African Institute of Min¬ing and Metallurgy, and other individual investigators. Information on the mechanical properties of rock and the behavior of the rock under a given system of stresses represents a necessary part of the information for rational engineering design for any given mining op¬eration. The mining method, the type and extent of sup¬port, the extraction ratio, the overall dimensions of the mine, and the orientation of the rooms and pillars are all decisions that are influenced by the mechanical prop¬erties of the ore, roof, and floor material under various stress systems and the magnitude and direction of the in situ stresses (Hooker, Bickel, and Aggson, 1972). Initial mechanical property information regarding a structure or mine property is generally obtained by two basic techniques: (1) static and dynamic property tests are conducted on intact and fractured rock specimens of exploratory drill core, and (2) dynamic properties are obtained by borehole logging techniques. When mining access becomes available, and as the mining horizon is expanded, additional information can be ob¬tained to verify preliminary mine design values. This chapter presents some of the standardized tech¬niques and equipment currently used in obtaining me¬chanical property data in the laboratory. The properties considered are: (1) uniaxial compressive strength of intact rock core specimens, (2) uniaxial compressive strength of rock cores containing planes of weakness, (3) triaxial compressive strength of intact rock core specimens, (4) triaxial compressive strength of cores with a plane of weakness, (5) Young's modulus, (6) Poisson's ratio, (7) density or apparent specific gravity, (8) modulus of rupture, (9) indirect tensile strength, and (10) creep characteristics. Where possible, an at¬tempt will be made to evaluate each property measure¬ment in relation to the problems of rock mechanics and application of results. TEST SPECIMENS The selection and care of drill core for laboratory testing require some consideration. It is recognized that laboratory-determined properties are not necessarily rep¬resentative of an in situ rock mass property. However, relative information between beds or zones of interest is still valuable information in selecting mining horizons and preliminary design criteria. To provide statistical data the number of drill core samples selected to repre¬sent each of the areas of interest should be from a mini¬mum of three to a maximum of ten test specimens. A judgment must also be made on site as to whether the recovered drill core should be wrapped and sealed in plastic to preserve moisture. On the one hand investiga¬tions of air-dried and saturated specimens have shown that moisture significantly affects the elastic properties and strengths of many rock materials (Obert, Windes, and Duvall, 1946; Colback and Wiid, 1965); on the other hand it is apparent that most core drilling is done with water which may saturate the specimen to a greater extent than in the in-situ condition. Whether or not the decision is made to retain the moisture, the core should be delivered to the laboratory as soon as possible after recovery for subsequent specimen preparation and testing. Specifications Shape: The shape of the specimens influences lab¬oratory testing in two ways: (1) time and cost of sam¬ple preparation and (2) strength of the material. Cy¬lindrical specimens of drill core are by far the least time-consuming to prepare for static or dynamic labora¬tory testing. In addition, the cylindrical shape lends it¬self to a more uniform stress distribution throughout the sample than other shapes, such as rectangles and hexa¬gons. The compressive strengths of various shapes have been studied (Grosvenor, 1963, and Price, 1960), and results indicate that the cylindrical specimens usually provide the highest strength for a given height-diameter ratio. However, reduction in strength from a cylindrical shape to a rectangular in situ pillar is not regarded as significant in relation to other considerations such as planes of weakness in a pillar or safety factors in the design process. Length-Diameter Ratio: The length-to-diameter ra¬tio, LID, has a significant effect on the compressive strength. Various recommendations have been made to use standard LID ratios ranging from 2 to 2.5 to 3 (ASTM, 1975c; ISRM, 1972). However, past work by others such as Obert, Windes, and Duvall (1946) has shown that excellent results can be obtained using LID ratios from 2 > (LID) > >/s. In selecting an LID ratio for testing, one should keep in mind the amount of material available for testing. In many instances, this may be limited. Thus, a shorter specimen such as 1: 1 LID may be necessary to provide enough test data for statistical analysis of results. Sec¬ond, it may be desirable to obtain elastic constants dur¬ing the test. This generally requires instrumentation such as linear variable differential transformers (LVDTs) or strain gages near the center of the specimen. In this case, an LID of 2.5 or 3 is desirable so that the instru

Jan 1, 1982