Search Documents

By T. S. Golosinski

Most of the 154 t (170 st) truck fleets that were predominant in large surface mines in the 1970s and 1980s are approaching the end of their economic life. One replacement option considered by mine operators is a change to the 2 18 t (240 st) trucks. A comparison of load capacities between the 1.54 t (170 st) and the 2 18 t (240 st) trucks indicates a large productivity advantage in favor of the 218 t (240 st) trucks. This advantage, however, is often reduced by a number of site-specific factors. Therefore, a careful evaluation is required to define the actual benefit of changing to the large trucks. This article discusses some important factors that have an impact on truck size selection, based on several different studies. 218 t (240 st) trucks The 2 18 t (240 st) rear dump trucks were first introduced for surface mine service almost 10 years ago. However, it is only during the last few years that this equipment has gained acceptance in the surface mining industry. About 250 units were employed in surface mines worldwide at the beginning of 1992, and further purchase commitments are being made. Encouraged by the mining industry’s interest, all major off-highway mining truck manufacturers now offer 218 t (240 st) models (Table 1). At present, the existing 218 t (240 st) truck fleets are dominated by electric drive trucks. However, recent introduction of a 2 18 t (240 st) mechanical drive truck rounds out the development of this truck size.

Jan 1, 1992

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By Cynthia S. A. Wallace, Joseph E. Crawford

The Culberson ore body is a bioepigenetic sulfur deposit located in the Delaware basin. Sulfur occurs in the Upper Permian Castile, Salado and Rustler Formations. Most of the ore body forms a subhorizontal layer within the Salado Formation. Abundant cave fill deposits of Rustler and younger lithologies occur within the Salado Formation and predate mineralization. The cave fill deposits provided porosity zones within the otherwise impermeable sulfate host rock and controlled sites of mineralization. A northeast trending fracture zone near the west edge of the ore body localized some deep mineralization and may have allowed migration of hydrocarbons from depth.

Jan 1, 1992

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By M. J. Zdunczyk

Located approximately 50 miles northeast of Knoxville, Tennessee, Short Mountain Silica mines the Clinch Formation, an orthoquarzite, for silica sand. In 1980, a Knoxville resident and area contractor visualized mining Short Mountain for silica sand. Because APG Industries, the main market for the glass sand product, was only 48 kilometers from the site, many silica sand companies became interested in the property. In 1986, J.D. Nicewonder began to develop the site, and in May of 1988, APG Industries received the first sand shipment.

Jan 1, 1992

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England&apos;s largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford&apos;s salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI&apos; and associated axjal plane cleavage SI&apos; and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2&apos;), a northeast trending crenulation cleavage (52&apos;), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2&apos;). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1&apos;, also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1&apos;, as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

By J. Guzman

Introduction The Carlin Trend is North America&apos;s premier gold producing district. It is located in northeastern Nevada&apos;s Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km&apos; (386 sq miles) in and around the Carlin Trend and own all or part of I6out of the 19 mines and prospects identified to date. Since the initiation of Newmont&apos;s exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont&apos;s Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output. The same incentives produced even more spectacular exploration results. In each of the last five years, net additions to reserves and resources outpaced current production by substantial margins. These facts demonstrate the spectacular past prospectiveness of the Carlin Trend and the success of focused, multi-disciplinary exploration methods that made it possible to more than offset the recent accelerated depletion of gold resources. However, is this situation sustainable? How long can the mining companies along the Carlin Trend keep on finding resources faster than they deplete them? These are some of the questions that motivated this study. The authors have not quantified the future potential for gold exploration in the Carlin Trend nor established a deposit discovery path. But strong indications were discovered that the [ ] Carlin Trend remains a relatively immature exploration district and that the potential for significant new discoveries is high. Methodology and data The approach chosen to address the above questions was simple. The authors compiled deposit size data, measured in contained ounces of gold resources, for all known deposits along the Carlin Trend (Table 1). The resource information was obtained by adding cumulative historical production (adjusted for mining losses and metallurgical recovery) to 1989 year-end published resource inventories. In a mature exploration area, where most deposits have been discovered, this distribution would be expected to approximate lognormality and would plot along a straight line on a lognormal probability scale. This result was found in previous work by Allais (1957) and recently confirmed by Cox and Singer (USGS, 1986) in regard to various types of mineral deposits in several regions of the world. It was also found to hold true for oil and gas pool size distributions (Arps and Roberts, 1958; Kaufman, 1962; McCrossan, 1969). [ ] The data used were compiled by Newmont Exploration geologists. The purpose of the study is to make inferences about the underlying geologic processes in the district and the maturity of the exploration effort. Therefore, deposits were not classified according to ownership but according to geologic occurrence as known from current information. Newmont&apos;s Post and Barrick&apos;s Goldstrike and Betze deposits, for example, are shown as a single occurrence to reflect the actual geologic setting. The cumulative frequency distribution of deposit sizes was plotted on lognormal probability paper (Fig. 2). The abscissa shows the cumulative fraction of deposits at or below a certain deposit size and the ordinate shows the deposit size in thousands of ounces of contained gold resources.

Jan 1, 1992

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today&apos;s and tomorrow&apos;s mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By Thomas J. Peters

The U.S. Bureau of Mines studied the 3,500-acre Winegar Hole study area, Idaho, a legislatively proposed (101st U.s. Congress) addition to the Winegar Hole Wilderness, Wyo.; it adjoins the western boundary of the Wilderness at the Idaho-Wyoming border, about 15 m; east of Ashton, Idaho. The study was part of an Idaho Land Assessment Program to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The study area is an east-west elongated, wooded plateau south of Falls River. Although the area is covered with surficial glacial deposits, it is probably underlain by volcanic flows; light-colored and mafic flow rock were noted in sparse outcrop. No mines, prospects, mineralized areas, or mineral resources were found in the study area during a literature and field search. The only nearby prospects include geothermal and rock aggregate (volcanic cinder) sites, and several placer claims. Although the Winegar Hole study area lies within a region of potential geothermal resources, no evidence of geothermal activity was observed. Rock in the area does not split into flat slabs, which could be useful as dimension stone, and would require crushing to be used 8S aggregate. Alluvium (placer) samples contain less than SO.01 per cubic yard gold (at a $350 per oz price); alluvial deposits are too small to contain gold resources.

Jan 1, 1992

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation&apos; of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992