Search Documents

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By Christina V. White

An experimental study was undertaken to investigate the feasibility of utilizing vapor transport for the treatment of heavy metal contaminated smelter soils. The focus of this project was to develop process chemistries that would make incineration a viable process for the treatment these soils. The experimentation concentrated on the elimination of arsenic, cadmium, and lead, and was performed in a laboramry scale rotary kiln setup. Three soil samples from non¬ferrous smelter sites, which contained various concentrations of contaminants, were utilized in the experimentation. Three chemistries were investigated for the volatilization of the heavy metals: Chloridizing volatilization, ferric chloride vapor complex formation, and the use of oxygen potential control. The samples were analyzed for residual heavy metals so that the extractions could be determined. However, the ultimate test was the leachability of the residual arsenic, cadmium, and lead, as determined by the TCLP test. The results firmly establish that incineration is a feasible process for the treatment of metal contaminated soils. It was found that no one process chemistry is suitable for all different soil samples. A two-step process consisting of a reducing step followed by a hydro-chlorination step was required to make Soil Sample-B pass the TCLP tests for all three heavy metals. Soil Sample-A passed the TCLP tests for arsenic, cadmium, and lead using a hydro-chlorination process at a minimum temperature of 700°C. In addition to passing the TCLP mm for Soil Sample-A and Soil Sample-B, 70 to 80 percent removal of the impurities was accomplished. This demonstrates that the leachability of the impurities was decreased primarily due to the removal of a large fraction of the contaminants, Soil Sample-C possessed very high levels of cadmium and lead and only moderate extractions of the impurities were generated from this soil. The arsenic TCLP test was passed at 500'C using a process gas containing ferric chloride and at temperatures of 700°C and above using chlorination of hydro-chlorination.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By John R. FitzPatrick

The separation and purification of uranium from either nitric acid or hydrochloric acid media tan be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated' to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps. We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (100-gram) flow experiments using depleted uranium, were done after the small-scale evaluation Of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments' involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and' amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process. Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail.

Jan 1, 1996

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world's primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By F. D. S. Marquis

An investigation of the mechanisms of formation of two types of porosity-primary and secondary-their characterization, evolution during processing, and effects on the mechanical behavior (fracture, fatigue, and failure) of 7X50 and 2X24 alloys has been conducted. The mechanisms of formation of three forms of primary or cast porosity were investigated, and each form was characterized: (a) macroscopic shrinkage porosity-MSP); (b) microscopic interdendritic porosity (MIP); and (c) hydrogen gas porosity (HGP) or primary hydrogen porosity (PHP). The mechanisms of formation of four forms of secondary or thermal/thermomechanical porosity were investigated, and each form of porosity was characterized: (a) high temperature oxidation (HTO). internal hydrogen precipitation (IHP), or secondary hydrogen precipitation (SHP); (b) preheating blistering porosity (PBP); (c) eutectic melting porosity (EMP);and, (d) dissolution micro void formation (DMF). The evolution and interactions of the primary and secondary types of porosity (w.ith special emphasis on PHP and SHP) during industrial and laboratory processing and their effects on the fracture and failure behavior of both types of alloys (with special focus on fatigue crack initiation and propagation) were investigated.

Jan 1, 1996

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

By B. Mishra

The application of various bydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, eg. metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been 'investigated and suggested for dealing with some of these wastes' and scrap material. The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained? from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EMI' and decontamination and decommissioning [D&D].

Jan 1, 1996

The U.S. economy and, consequently, the demand for minerals grew at more moderate rates in 1995 compared with stronger performances the previous year. Demand for metals such as steel and copper was relatively stable. For example, the decline in steel consumed in motor vehicle manufacturing (reflecting lower vehicle sales) for the first half of 1995 was offset by an increase in steel consumed in construction during the same period. More detailed information on events, trends, and issues in the mineral and material sector Is presented below and in the commodity sections that follow. Overall Performance The value of processed materials of mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10% compared with 1994. The estimated value of U.S. raw nonfuel minerals production in 1995 was $38 billion, about 7% more than in 1994. The value of U.S. minerals production has increased in 30 of the last 35 years.

Jan 1, 1996

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

By Lee R. Martin, Michael R. Taber

Bird Balls™, the latest development in the ongoing battle at mine sites across North America, help to eliminate accidental avian mortality caused by birds ingesting cyanide leachate. Bird Balls™ are a 4-inch sphere made of high-density polyeth­ ylene (HDPE). They weigh 40 grams and are black in color to provide optimum life in UV intense environments. A floating blanket of bird balls totally excludes birds from a liquid surface. Federal agencies that enforce the Migratory Bird Treaty Act do not specify how to keep migratory birds out of leachate basins. Some state agencies, however, specify that a physical barrier must be in place to exclude migratory birds if cyanide levels are high enough to cause mortality. Industry standards for protecting waterfowl now include Bird Balls™ as well as net­ting, detoxification, and heap leach systems designed in such a manner that no exposed solution ponds or channels exist. Hazing is no longer an option. A bold statement to make? Perhaps, but W. R. Jeffress (1990) covers the subject well when he stated that, "Hazing techniques as a whole have not been effective in excluding waterfowl or other species of wildlife from toxic heap leach solution ponds or tailings impoundments. Research and devel­opment of the new 'Star Wars' hazing techniques, such as laser netting and radar systems, are interesting concepts and will pos­sibly offer an alternative to total physical exclusion or neutral­ization in the future. All of these methods are going to have to be thoroughly tested." For those who may want further docu­mentation, we have included a special reference section cover­ing hazing. R. J. Hallock (1990) stated that, "The Fish and Wildlife Service is particularly interested in migratory birds. In fact, a large portion of our effort, nationwide, is focused on migratory birds. Bird habitats are managed directly through the National Wildlife Refuge System and indirectly through other agency programs. We also have a responsibility to protect birds under the Migratory Bird Treaty Act. Most birds attracted to mine ponds are covered under this Act. The only migratory birds not protected under the Migratory Bird Treaty Act are English Sparrows, Starlings, and Pigeons. Since this is a treaty with five nations, the concept of acceptable losses does not apply. It is not a negotiable situation. There are a few exceptions noted in the Act, including prescribed hunting of selected waterfowl, scien­tific collection, and game bird farming. There is no exception for the loss of migratory birds exposed to solutions of cyanide."

Jan 1, 1996

By E. H. Cho

A current environmental concern is the cleanup and restoration of soil contaminated with low-level radionuclides at DOE sites including the Nevada Test Site. At the present, there is no applicable process to economically and effectively deal with the remediation of contaminated soils. This situation requires development of a selective flotation process to separate the radionuclides from contaminated soil efficiently and economically. In this study, a minus 200 mesh size fraction of pure cerium dioxide was used as a surrogate for plutonium oxide which is the major contaminant at the Nevada Test Site. A Hallimond flotation cell was utilized to examine the flotation behavior of cerium dioxide with oleic acid under various conditions of pH and collector concentration Mechanical cell tests were conducted to float the surrogate from a mixture with uncontaminated Nevada Test Site soil in the absence and presence of calcium carbonate as a carrier. Two different sizes of the carrier (minus 150 mesh and 65-150 mesh) were tested. It was found through the Hallimond cell flotation tests that the cerium dioxide could be floated well at pH's 4 and 9 with 10-3 molar oleic acid. It was also found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34 % to 65 % by adding only 0.5 % calcium carbonate (minus 150 mesh) in the feed and also increased to 95 % by adding 10 % of this carrier to the feed. The finer size fraction of calcium carbonate (minus 150 mesh) was more effective in recovering cerium dioxide than the coarser size fraction (65-150 mesh) The flotation method utilizing a carrier of calcium carbonate seems to provide a high potential to be used for the remediation of soil contaminated with radionuclides at various Department of Energy's nuclear weapon sites.

Jan 1, 1996