Search Documents

On 15 August 1998 the first section of the PUTRA LRT system was opened to the public as a free service prior to official commencement of revenue service on 1 September 1998. It is a remarkable achievement to open a highly advanced medium capacity urban railway scheme in four years after the outline concept began. Even more remarkable is the implementation of the next stage which is the underground section planned to be operational in mid-1999. The decision to build the first underground railway in any major urban centre is a technical challenge. The PUTRA LRT System can be likened to Hong Kong when the initial MTR system began in the 1970s and Singapore MRT in the 1980s. Prior to the PUTRA railway very little bored tunnelling had been undertaken in Kuala Lumpur. A few shallow sewer tunnels had been built but the main experience of tunnelling in Malaysia had been for water, hydroelectric and road tunnels usually through granite formations. The ground conditions in Kuala Lumpur were known mainly from experience of piled foundations and occasional deep excavations. The suitability and likely difficulties to be experienced during bored tunnelling could only be theoretically predicted. In both Hong Kong and Singapore, government owned corporations were set up to implement the scheme, but in Kuala Lumpur the whole project has been undertaken by a private company PUTRA, a wholly owned subsidiary of Renong Berhad.

Jan 1, 1999

By V A. Diemar

The Chatree Gold Project represents a greenfields discovery of metallurgically clean shallow gold mineralisation in a logistically simple terrain. Total Measured, Indicated and Inferred Resources are currently 31 tonnes of gold and 160 tonnes of silver. Gold occurs in an adularia-sericite epithermal system within quartz-calcite-adularia veins, breccias and stockworks. Host rocks are volcanic arc porphyritic latite-trachyte flows, their pyroclastic equivalents and volcaniclastics of upper Permian to upper Triassic age. The mineralisation was deposited in dilated zones during repeated reactivation of pre-existing structures. To-date five mineralised prospects have been defined by drilling with three reaching JORC Code Mineral Resources status. The project is in its definitive feasibility stage and is anticipated to be in construction during 2000.

Jan 1, 1999

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By P. J. Mackey

"The metal producing industries in Canada and in the U.S. in many ways owe their technical beginnings to Welsh technology. The first copper smelter in Canada started in 1849-50 with a Welsh reverberatory furnace and skilled furnacemen brought across from Swansea to operate the equipment1- The Rocky Mountain smelting industry began with the installation of furnaces resembling the Swansea smelters(2). It was only later that the North American industry developed newer and improved methods. This article briefly describes the metallurgical history of the Lower Swansea Valley, being that section of land stretching northward from Swansea along the banks of the River Tawe, and bordered by hillsides east and west of the river. The Valley has had a classic cycle of development and decline common to industrial areas of Britain which grew in the Industrial Revolution. Perhaps more than any other area today, the Swansea Valley represents a complete cycle of use from agricultural to the peak of industrial development through to decline and dereliction. The conditions which made the Tawe Valley attractive to certain industries were laid down nearly 300 million years ago with the Carboniferous swamps and forests which covered the area, later forming the south Wales coalfield. As a result of glacial action and the deposit of glacial outwater and alluvial gravels, the valley adopted the traditional configuration, with its rocky sides occasionally remaining exposed. Up to probably about the 16th century, the Lower Swansea Valley was similar in use and appearance to many other valleys in the region. From the 14th century, the natural oak woodland had provided a continuous source of timber to produce charcoal for iron making as well as for structural purposes. Agriculture was the main activity in the valley in this period, but it was likely that the farmers also mined small amounts of coal by way of ""bell pits"", and adits into the coal seams."

Jan 1, 1999

By J. E. Dutrizac, J. B. Sunstrum

Until relatively recent times, virtually all gold was recovered by gravity and/ or amalgamation methods. Although such techniques are very effective on coarse gold, they become increasingly less useful for finer grains especially when the gold is partly enclosed in rock matrix. Throughout the nineteenth century a number of bonanza gold fields were found in the United States, South Africa, Australia and Canada. In every case the abundant supply of gold nuggets and coarse alluvial gold soon gave way to hard rock mining with its inevitable losses of fine gold in the stamp mill tailings. Continuing efforts to develop new technologies capable of dissolving gold from finely ground ore were eventually successful first with chlorination (the Plattner process) and subsequently with cyanidation. Even before the nineteenth century, however, European chemists such as Scheele and Berthollet were aware that gold could be readily dissolved in an excess of free cyanide(1). As early as 1840, a patent was issued to the Elkington brothers for the dissolution of pure gold in cyanide solution and its subsequent plating onto various metals, with or without an applied electrical current. In 1846, Elsner showed that oxygen was also required to solubilize gold or silver in cyanide media(1). Despite the fact that much work was done on the reaction of cyanide solutions with gold, a viable leaching process for gold ores did not quickly emerge although cyanide solutions were used to enhance amalgamation from the 1860s onward. Major problems were associated with the use of concentrated cyanide solutions; the costs of cyanide were excessive and it was difficult to recover gold from the concentrated media.

Jan 1, 1999

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, a better means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas and was called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' 0 x 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.c., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" 0 X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By N Belluz, L Johnson, N Wiwoho, P Manning

The Kucing Liar skarn deposit is located in the Ertsberg mining district, which also contains other skarn deposits and the Grasberg porphyry copper û gold deposit. The Ertsberg district is located in the province of Irian Jaya, IndonesiaÆs easternmost province. Mining development began in the Ertsberg district in 1972 with the mining of the Ertsberg deposit. Daily production in the district now averages about 230 000 tonnes of ore, with the bulk of the ore coming from the Grasberg open pit and the balance from underground mining of skarn deposits. During 1998, 45 218 additional metres of drilling were conducted to delineate and understand the Kucing Liar orebody. The deposit was first intersected in drill holes in 1994 and then was intersected in underground workings located about 1000 metres from the discovery drill hole in 1995. Initially, the two intersections were thought to be different orebodies but are now realised to be different parts of the same orebody. The Kucing Liar deposit consists of magnetite û copper û gold replacement and skarn mineralisation in favorable Tertiary and Cretaceous units. The deposit is approximately 2000 metres in length and averages about 200 to 250 metres in thickness. The width varies from 400 to 600 metres. Drilling in 1998 was directed towards delineating the deposit on its NW and SE ends and to determine its down dip extension. Reserves for the deposit at the end of 1998 stand at 320 million tonnes at 1.4 per cent copper, 1.4 g/t gold, and 5.3 g/t silver. Many important questions remain to be answered concerning the relationship of the Kucing Liar orebody to the major faults in the district and to the Grasberg intrusive complex which contains the Grasberg orebody. Continued exciting developments are anticipated as work to understand the deposit by drilling and geologic study continues.

Jan 1, 1999

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are l<aolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By S Pontual

Compact and field portable infrared spectrometers have been increasingly used over the past few years by an exploration industry constantly searching for a technological edge and the ability to more accurately and rapidly assess project areas. In particular, this technology allows large amounts of data to be rapidly collected on-site and sample mineralogy, mineral crystallinity and mineral composition to be quickly assessed. In recent years, short wave infrared (SWIR) reflectance spectroscopy has proved useful in a wide range of geological environments and at various stages of exploration programs, from grass roots reconnaissance through drilling programs and resource evaluation. Unfortunately these data have frequently been analysed and interpreted in isolation using time consuming data analysis techniques removed from the realities of a fast moving exploration industry. This paper presents new analysis techniques which allow these data to be efficiently integrated in the exploration program. Although SWIR data contain a wealth of mineral information it is impractical to use this information in its raw form. A more effective approach involves the extraction of key characteristics of these data (ie mineralogy, mineral composition and crystallinity) as numerical values, and the integration of this ædigital mineralogyÆ with more conventional exploration datasets (eg geochemistry, coordinate data, etc). This paper demonstrates that the integrated analysis of sound geological observations, geochemical, spatial and spectral data can quickly lead to a greater understanding of the nature and distribution of target mineralisation. As a first step, software driven pattern matching routines enable the identification of the major clay mineral species in a series of samples (eg kaolinite, montmorillonite and sericite). This allows the major alteration facies and their spatial distribution to be identified. Quantification of diagnostic absorption feature characteristics then allows more accurate determinations of mineralogy to be made (eg mineral composition and crystallinity). Examples of the application of SWIR analysis for alteration mapping from selected porphyry and epithermal systems from around the Pacific Rim are discussed. The data presented are derived from a variety of locations and sample types including drill core, ridge and spur rock chip samples, soil samples and geochemical pulps. In these large alteration systems, the spectral data can be used to describe and map the distribution of various alteration facies as many of these are characterised by clay and phyllosilicate mineral assemblages and are detected by SWIR analysis (eg smectite, chlorite, biotite, illite, muscovite, kaolinite, dickite, pyrophyllite, alunite, etc). In addition, the ability to evaluate even subtle trends in mineral crystallinity and composition is often vital in these systems when looking for vectors towards higher temperature parts of the system. In addition to detailed evaluation of mineralogy, the integration of digital mineralogy data with geochemical data leads to the ability to describe not only geochemically anomalous intersections or regions but also to recognise associations between subtle changes in mineralogy and target mineralisation. This is often important because understanding these mineralogical associations can lead to more accurate targeting and rapid assessment of the project.

Jan 1, 1999

Whilst employed by Dyno Nobel as the Technical Services Engineer û Brisbane, I was asked, as part of a contractual agreement, to look at optimising PioneerÆs blasting process to provide the most effective rock to the new crushing and screening plant. This paper details the preliminary blast designs and practices that have been in use at the quarry and the initial changes made to these designs, and the effect they have had on the excavation and crusher performance.

Jan 1, 1999

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

By Gregg Vickell

"High tonnage, low grade gold mines such as Omai’s afford economies of scale that are unto their own insufficient to sustain profitability at today’s depressed gold price. Complimenting profitability objectives is the perpetual challenge to reduce operating costs and optimize unit operating efficiencies while being ever vigilant of issues such as environmental control.Key to achieving these objectives at Omai are throughput and availability gains, gold recovery improvements, cost cutting, a skilled workforce and reliable power generation.This paper attempts a cursory review of startup-to-date plant performance advances and future performance-driven objectives.INTRODUCTIONCommercial gold production at Omai commenced in January 1993 with annual output climbing to 250,000 opy by the end of 1994. A mill expansion completed in August 1996 increased gold production to 340,000 opy by the end of 1997. Current milling capacity is 20,000 in tpd (nom.) with actual capacity exceeding 24,000 mtpd on occasion depending on ore size and competency. Mill feed consists of hardrock (andesite, quartz diorite and rhyolite) and softrock (saprolite, laterite) at a nominal ratio of 70:30, respectively. Present day average weighted grade of the feed is 1.4 g/t gold.PROCESS DESCRIPTIONPrimary crushing, ore handling and the original 12,000 mtpd hard and soft rock SABC mill, hereafter referred to as Mill ‘A’, remains essentially as documented by Konigsmann (1 994) complete with poststartup modifications. The mill expansion, hereafter referred to as Mill ‘B’, features an 8000 mtpd hard rock SABC grinding circuit similar in configuration to Mill ‘A’ and differing only in equipment size. Mill ‘B’ includes a 9000 H.P.,reversible variable speed , single pinion drive, 32 ft. x 15 ft. SAG inill , a 7 ft. short head pebble crusher and two parallel 5400 H.P., 16.5 ft. x 30 ft. ball mills with dedicated cyclone packs consisting of D26 hydrocyclones."

Jan 1, 1999

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By H. A. F. de Souza, Dana S. Mills, P. E. Burgener

"ICP-MS has moved from a laboratory curiosity to a functional analytical tool. This paper discusses how ICP-MS has been used to solve difficult analytical problems encountered when analyzing various mine materials. Comparisons between analytical techniques applied to the analysis of gold and the platinum group metals illustrate the advantages and problems of ICPMS when. applied to trace levels of some metals iri the presence of ore grade metals. Interferences and matrix effects are compared to ICP, AA and Neutron Activation. The necessity to select chemical extractions which are compatible with ICP-MS are also discussed.The ICP-MS techniques explained in the examples on Au and precious group elements (PGE) have validity in analytical problems encountered in testing of trace metals in the presence of major elements found in mine materials. Exploration and environmental testing are other areas that require the same analytical approach to quantify trace levels in the presence of major interfering elements normally associated with mining environments."

Jan 1, 1999

This paper describes a simple finite element (FE) modelling approach which leads to the computation of seismic energy release rate (ERR) and strain energy storage rate (ESR) which result from mining. The concept of critical strain energy is introduced as a means to help evaluate the strainburst potential in mine structures. A new, energy-based, burst potential index (BPI) is proposed. The use of ERR, ESR and BPI is demonstrated by a cut-and-fill stope case study. The merits of using such energy parameters in the interpretation and analysis of strainburst phenomena are discussed. While the study gives promising results, site-specific back analyses would be required to first calibrate the model and fit it with the local mine conditions, before it can be adopted as a routine design tool.

Jan 1, 1999

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999