Search Documents

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

By Brenda J. Burd

A very extensive spatial and temporal database on benthic infauna and associated sediment metals has been collected for Island Copper Mine on Vancouver Island, B.C. Canada from 1969 (pre-discharge) to 1998 (3 years post-discharge). The tailings deposited as organically impoverished, copper-rich, clays, silts and sands distributed according to particle size, bottom turbidity currents and strong, vertically mixed tidal currents. In addition, a large deposition of coarser waste rock along the north shore of Rupert Inlet contributed substantial material in the shallower, near-field area.

Jan 1, 2001

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By Robert E. (Bob) Brown

Magnesium was discovered by Davy in 1808. The production processes as they exist are not economically competitive with aluminum The electrolytic magnesium process is divided into two steps; one to make the MgCh feed and the other to apply large amounts of electric current to dissociate the feed into magnesium (450 g) and chlorine (1200 g). The production of fuJIy anhydrous, pure cell feed is a major problem Recently, there has been a growth of thermal processes, mainly the Pidgeon silicothermic production process using FeSi to reduce dolomite in horizontal retorts. Pechiney has a large vertical electrical furnace process that also uses FeSi to reduce calcined dolomite in a molten bath containing alumina. Work is proceeding to develop new or modified processes that will greatly improve magnesium production. The present methods and the research and R&D will be reviewed in this paper.

Jan 1, 2001

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By Matthew John M. Krane, Christopher J. Vreeman, J. David Schloz

"A continuum mixture model of the direct chill casting process is used to model the transport phenomena and solidification behavior in the Direct Chill casting of an Al - 6 wt% Cu billet using Wagstaffs AirslipTM process. The model, which includes the transport of free-floating solid particles, can simulate the effect of a grain refiner on macrosegregation and fluid flow. Numerical predictions of sump profiles and composition and temperature fields are presented. Two 45 cm diameter billets were cast under production conditions with and without grain refiner. Temperature and composition measurements and sump profiles are compared to the numerical results. The comparison shows excellent agreement for the grain refined case. It is believed that an incorrect model assumption prevents good agreement in the non-grain refined billet. IntroductionDirect chill casting is a semi-continuous process in which molten aluminum enters the top of a water-cooled mold, is cooled, and forms a solid ingot drawn out below (Figure l(b)). The molten aluminum begins to solidify due to the cooling effect of the mold wall. As the ingot is withdrawn from the bottom of the mold, water jets impinge on the surface, directly cooling the billet and forming a solid layer around a liquid melt, commonly referred to as the sump.A particular defect that occurs in a wide range of casting processes, including the direct chill (DC) casting of aluminum alloys, is macrosegregation, the uncontrolled redistribution of alloying elements on the scale of the ingot during solidification. Macrosegregation in DC cast ingots can produce non-uniform mechanical properties [l], which affects the behavior of the metal during downstream forming and heat treat operations."

Jan 1, 2001

By R. J. McGregor

The Internet has revolutionized worldwide communications. Any real or perceived mining incident or environmental spill, no matter how small or remote, can become a disaster of "biblical proportions" through the judicious use of the Internet by environmental and anti-mining groups. In addition, mining companies' own Web sites and unofficial message boards can provide plenty of additional ammunition to the anti-mining forces. This paper explores how the Internet and readily available information are used by anti-mining groups active on the Web.

Jan 1, 2001

In November 1999 Waihi Gold Mining Company commissioned its new crushing and conveying plant used to transport both ore and waste from the Martha Mine to its ore processing plant and also its tailings dam construction area. To date, a record monthly throughput of 854 000 tonnes throughput has been achieved. This paper outlines the measures taken subsequent to the commissioning of the system to achieve greater than design throughput and to mitigate the environmental and safety issues associated with operating the system in the middle of a town.

Jan 1, 2001

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

By Yannick C. Beaudoin

Southern Explorer Ridge (SER) is an anomalously shallow, intermediate-rate spreading ridge located 200 kilometers off the west coast of Vancouver Island, Canada. It ranges in depth between 2600 m (deepest basins) and 1760 m (bathymetric minimum). At least 60 sulfide deposits are known to be associated with hydrothermal vent fields along the ridge. For the first time geological data, including deposit locations, collected from 15 marine expeditions to SER since 1983 have been assembled in a GIS format. GIS processing techniques were employed to plot the distribution of base metal concentrations for recovered sulfide samples. The highest base metal concentrations are found in the vicinity of the Magic Mountain site (main active vent field), and also proximal to a side scan sonar anomaly referred to as AGOR 171. Individual samples near these locations have yielded values as high as 29.3 wt\% Cu, 34.3 wt\% zinc, 0.97 wt\% Pb, 2.0 ppm gold, and 664 ppm silver. Sample paucity is the key limiting factor that prevents adequate assessment of the areas economic potential.

Jan 1, 2001

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Francois Reizine

Infrared sensors will include scanning detectors and positioning sensors. The focus will be on 1, 2, and 4-color wavelength pyrometer systems which allow the accurate measurement of emissivity and, consequently, of the true temperature even in the presence of scale, slag, and fumes. Such sensors are being used in blast furnaces, BOF's, and galvanizing lines. Laser sensors will be presented using different principles of physics, mainly time-of-flight, pulsed infrared lasers for level measurement and dimensional measurement; triangulation lasers for width and thickness measurements; and laser Doppler velocimeters for velocity and length measurements, including mass flow, elongation, and tension control, cut-to-length applications. These sensors and systems are based on state-of-the-art technical developments to improve productivity and quality and reduce maintenance and downtime.

Jan 1, 2001

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001