Search Documents

By P K. Banerjee, S Kumar

Indian iron ores with less than 62 per cent Fe are currently unexploited, except for a few sectors which export them to foreign countries. It is anticipated that by 2012 the countryÆs domestic steel production is likely to rise to the tune of 60 million tonnes per annum. To meet this requirement, it is necessary to utilise not only the existing high-grade deposits but it is also necessary to look into exploiting the leftover iron ores of lower grades. Hence, reserves with Fe content 62 per cent and below (particularly the ores with In the present paper, an attempt has been made to beneficiate three different types of low-grade iron ores selected from three different parts (states) of the country. In the paper, alternative routes for beneficiation and effective utilisation have been tested using different techniques in the laboratory in an attempt to match their (Al2O3/SiO2) ratio after thorough characterisation and liberation studies. The paper also encompasses the geological formations, occurrences and distribution of Indian iron ores as well as highlighting the problems associated with the fines, possible metallurgical routes, and their market segregation from the perspective of end users.

Jan 1, 2007

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By H. Basarir

Due to the environmental constraints and the limitations on blasting, ripping as a ground loosening and breaking method has become more popular in both mining and civil engineering applications. Because of the technological advances in dozer manufacturing techniques, more powerful dozer types are available today. Thus, the ground, previously classified as non-rippable, has become rippable. As a consequence, a more applicable rippability classification system is needed which considers both equipment properties as well as rock properties in all applications. This paper is part of a complementary research work and presents the development of a previously published grading rippability classification system by the application of fuzzy set theory. The integrated rippability classification system considers the combined utilization of the rock and equipment properties, as well as expert opinion. Fuzzy set theory was chosen mainly because it deals well with uncertainty in the choice of variables. Although there are apparent sharp or discontinuous boundaries in existing classification systems, practically most of the factors involved in the ripping process are less well defined and boundaries are more blurred (or fuzzy) or uncertain in nature. Also by means of fuzzy logic it is possible to eliminate bias or subjectivity. The validity of the proposed system was checked by the comparison against existing classification systems and direct ripping production values obtained at studied sites. It is seen that by means of fuzzy logic, the uncertainties are reduced and biased usage of the final ratings that appear in alternative systems are efficiently dealt with. Keywords: Fuzzy set theory, rock rippability, rippability classification system, direct ripping, fuzzy inference system.

Jan 1, 2007

By D La Rosa, A Jankovi, A Dance, W Valery

This paper presents the methodology for optimising blasting and comminution processes in terms of fragmentation developed by Metso Minerals Process Technology Asia-Pacific and South America (MMPT). The methodology is called process integration and optimisation (PIO) and involves a number of steps: benchmarking, rock characterisation, measurements, modelling/simulation of blasting and comminution processes and where required, material tracking. The measurements collected while at site are combined with rock characterisation and definition of ore domains to model the complete process chain. These data are used to develop site-specific models of blast fragmentation, crushing, grinding and flotation. This allows customised blast patterns to be developed that optimise both crushing and grinding performance. For each domain, blast designs are recommended to generate the optimal fragmentation size for downstream processes. The objective is to minimise the overall cost for the entire process and the changes often have a positive impact on the mining operation. Process constraints such as wall stability, ore dilution, muck pile characteristics, size of mining equipment, size and installed power of crushing and milling equipment and other process bottlenecks are considered in the blast designs. This methodology has allowed many operations around the world to significantly increase their production: generating typically five to 20 per cent higher concentrator throughput. A number of case studies will be discussed in this paper to describe the structured approach taken and demonstrate the benefits that are achievable. This paper will focus on the role of blasting in the optimisation of the entire mine to mill process chain and discuss elements of the PIO methodology: rock characterisation, fragmentation modelling and measurement, the relationship between fragmentation and mill throughput and material tracking.

Jan 1, 2007

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By R. P. Zahn

The need for quantitative mineralogical data to characterize ore types before they are processed is becoming increasingly necessary. Mineralogical data (modal abundances, grain size, liberation/locking characteristics, mineral textures and associations) can provide invaluable information to facilitate the identification of metallurgical issues that may arise during processing of a particular ore. This paper will discuss the use of QEMSCAN analysis in conjunction with bench scale flotation test work to determine metallurgical characteristics for several ore types that will be fed to the Morenci concentrator upon commencement.

Jan 1, 2007

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

Thermo Fisher Scientific is the worldÆs leading supplier of analysers for laboratories and process industries. The companyÆs X-ray fluorescence (XRF)-based slurry immersion probes were originally developed by the acquired Amdel Instrumentation. These analysers have found limited application within wet beneficiation plants for measurement of iron. The recent trend of renewed efforts to maximise recovery from existing resources and lower costs has increased industry interest in online analysis. In the mid-1990s the company developed online analysers (the light element slurry analyser û LESA) for slurry applications using the prompt gamma neutron activation analysis (PGNAA) method. The company has successfully installed LESA for the direct measurement of lighter impurity elements in Brazilian plants using flotation for rejection of silica. A case study is presented. The PGNAA technique has the unique ability to provide elemental analysis of bulk materials on a conveyor belt. The company released its eighth generation cross belt Omni analyser using PGNAA in 2007. Results from a recent project with sinter are presented. The Niton range of hand-held XRF analysers is also supplied by Thermo Fisher Scientific. These handy devices are finding widespread use in the mining industry to provide quick and easy analyses in exploration settings. In contrast to PGNAA this is a surface technique. A prototype for light element analysis is being tested for iron ore.

Jan 1, 2007

By M. Ruel

In today&apos;s highly competitive worldwide market, it is becoming extremely important for managers to make sure that all resources are used where needed the most. That way, all resources are generating added value, process control equipments are maintained in an optimal state for best performance, and final product is produced at least cost. Performance monitoring is the only way to ensure that everyone is working on top priorities toward the same goal. How can we add value to these warehouses of data? The data is there and the information is hidden; it is just waiting to be extracted. A process performance monitoring system is able to determine if a loop, a system, a unit, or a plant meets the expected performances. The system prioritizes the areas that need attention. It also provides historical reports of the plant status by areas, by loops, and by identified problems. This information is provided to different categories of users in an appropriate format for each one. The system also includes diagnostics and tools to detect and analyze problems.

Jan 1, 2007

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors&apos; aim to demystify the basic Six Sigma principles.

Jan 1, 2007

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By D McKeon

In July 2006, ten Mining Engineering students and Associate Professor David Laurence from the University of New South Wales (UNSW) participated in the universityÆs inaugural overseas mining field trip. The ten-day trip to western Canada involved visits to two mines in British Columbia, the Diavik Diamond Mine in the Northwest Territories and the Syncrude oil sands operation in Alberta. Importantly, the groupÆs main objective was to gain a global understanding of todayÆs mining industry by observing the different cultural, legal, social and environmental setting found in Canada. It should be noted that the entire trip was planned, organised and directed by the students and benefited from extensive industry support both in Australia and Canada. This report intends to provide an overview of the field trip and describe to a limited extent the Canadian approach to mining.

Jan 1, 2007

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

By M Sebbag, T Taimre

Barrick Gold Corporation is proceeding with development of the Buzwagi Mine in the Lake Victoria Greenstone Belt District of Tanzania. The Buzwagi orebody occurs in the Nzega Shear zone within the Greenstone Belt and is hosted in a K-Feldspar rich granite in contact with mafic volcanic. The orebody presents 2.6 M ounces in 41 Mt of reserves, at 2.0 g/t. Over the ten year mine life, total material movement will be 261 Mt. The feasibility study was completed in 2006 and presented several technical challenges. Two principle challenges are grade control and the impact of dilution on the economic viability of the project. The principle challenges for grade control will be quality control and quality assurance in the sampling of the massive coarse grained granite, which comprises 70 per cent of the deposit. The principle challenge with dilution will be with the selective mining of the narrower mineralised zones contained within the mafic volcanics. This paper will focus on the mine planning methodology which has been applied including selective mine unit (SMU) and dilution estimation, net smelter revenue (NSR) calculation and the effects of cut-off grades to the project economics and mine schedule.

Jan 1, 2007

By J. J. Crowder, A. L. Coulson

Ground support is a significant component of underground mining costs. The rehabilitation of failed support, however, is often much more expensive than the initial installation. This paper investigates whether the right type and length of support can be designed correctly the first time, through forward modelling of the support and the mining process. Back analyses demonstrate how high-quality instrumentation and monitoring can help with the estimation of the post-peak (post-failure) rock mass parameters required for a comprehensive analysis. A hybrid modelling approach combines a three-dimensional mine-wide boundary element model with a non-linear finite element model to allow for the failure process in the rock mass. The back analyses demonstrate that, for the case study site, the post-peak Generalized Hoek-Brown value of mr must be reduced significantly in order to properly simulate displacements observed in instrumentation data. High-quality instrumentation data is the key to post-peak rock mass parameter calibration. The procedures outlined in the paper highlight the need for a new hybrid numerical modelling package that can use the influence of three-dimensional mining-induced stresses to predict displacements in, and potential failure of, rock masses surrounding mining infrastructure in order to radically alter strategic and tactical mine design.

Jan 1, 2007