Search Documents

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014

By Herman Mendoza, Luisa Ciriaco

An investigation of the seeding mechanism using heterocoagulation and the Derjaguin - Landau - Verwey - Overbeek (DLVO) theory of two pure minerals is the objective of this study. The seed was silica with modal diameters of 4.529 µm (fine particles) and 5.216 µm (coarse particles) and the test powder was hematite with a modal diameter of 0.883 µm. Parameters included variations in the concentration and particle size of silica. Both particles were first subjected to size determination and settling tests via Stoke’s Law. The silica-hematite system was then suspended in 0.001 M KNO3 electrolyte solutions where pH was adjusted. Afterward, the suspension was agitated and was allowed to settle at different time intervals while obtaining turbidity readings. Results through settling time and turbidity vs. pH graphs indicate that maximum heterocoagulation occurs from pH 2 to 5 while minimum heterocoagulation occurs from pH 6 to 7. At these pH levels the zeta potentials of silica and hematite are negative and positive, respectively. On the contrary, repulsive forces dominate the system from pH 8 to 11 due to the particles’ negative zeta potentials. Furthermore, the attachment of hematite to silica increases when the parameters become larger thereby increasing the effectivity of heterocoagulation at acidic to neutral pH levels.

Jan 1, 2014

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By A. Bahrami

Andalusite, silimanite and kyanite are polymorphs of aluminosilicate known as kyanite group. Minerals of this group are used in refractory. Sarband andalusite deposit is located in Markazi province in Iran. Mineralogical studies showed that the main minerals of this sample are andalusite (5%~10 %), mica, quartz and feldspar. Processing of the samples was carried out using two sizes, i.e. +500 µm and -500 µm. In the processing of +500 µm scrabble test was carried out on -4750 +500 µm and -2380 +500 µm. For -500+300 µm shaking table and magnetic separation were applied. For -300 µm fraction, flotation was carried out. The results of this tests showed that the processing of Shazand andalusite was not possible, because silica and iron impurities were diffused inside the andalusite mineral grains.

Jan 1, 2014

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By J. J. Lui

Surfactant plays a critical role in many industrial processes such as petroleum, mining, environment and food processing, and daily life. For ionic surfactant systems, adsorption of surfactant at oil-water interface imposes a net charge to the interface. The nature and magnitude of the charges at the oil-water interface depend on charge characteristics of surfactant molecules, concentration of surfactant and solution pH. In our previous study, zeta potential measurement of hexadecane drop-lets in industrial process water was shown to be a simple, yet powerful method for identifying various types of ionic surfactants present in the aqueous system. In this paper, the site-binding model was applied to prediction of zeta potential of oil droplets in aqueous solutions containing a mixture of cationic and anionic surfactant molecules. The total number of interfacial sites for various types of surfactant involved was determined by applying the Gibbs adsorption equation to the measured interfacial tension-surfactant concentration profiles. The distribution of various types of surfactant molecules at the interfaces was evaluated by Langmuir isotherm constants. With the ionization constant of surfactant taken from the literature, the predicted zeta potentials of oil droplets in surfactant solutions from site binding model were shown in a reasonable agreement with the measured zeta potential values.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By E. Hardwick, K. C. Sole, Y. Jurrius

"The Luilu cobalt plant at Kolwezi, Democratic Republic of Congo, has been operating since the late 1950s, using a conventional precipitation flowsheet for removal of impurities from the cobalt process stream. Most impurities are, however, incompletely removed using this technology. Copper and zinc, both of which quantitatively deposit at the cathode in the cobalt electrowinning process, are two of the main impurities contaminating the cobalt metal product. Ion exchange offers a modern approach to removing these impurities from the cobalt advance electrolyte.Following a laboratory testwork programme to identify a suitable ion-exchange system, an on-site pilot-plant trial, treating 1500 to 3000 L/d of electrolyte, was operated for a period of six weeks to optimise the operating conditions and to determine full-scale design criteria. Copper removal was carried out using a fixed-bed lead-polish configuration with the Lanxess iminodiacetic acid resin, TP 207. Zinc removal was subsequently carried out in a similar configuration using the Lanxess aminophosphonic acid resin, TP 260. The optimised system proved capable of removing both copper and zinc from 20 to 30 mg/L to <1 mg/L from plant electrolyte containing ~20 g/L Co. Selective elution allows co-loaded cobalt to be returned to the main circuit and value to be obtained for the copper impurity. The process shows operational and economic advantages over the traditional flowsheet. Full-scale implementation of the developed process is in progress and some design considerations are discussed."

Jan 1, 2014

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By C. Y. Jia

Adsorption of Thiooxidans ferrooxidans and Mycobacterium Phlei on the surface of pyrite and galena was studied. From the experimental results, it was observed that Mycobacterium Phlei adsorbed preferentially on pyrite than on galena at neutral and alkaline pH values, while Thiooxidans ferrooxidans is not at all pH range, and the scanning electron microscopy photograph also indicated that. FTIR and XPS of two strains of bacteria indicated that there are much functional groups on surface of them, such as O?H, N?H, C-O, C?N, C?O etc, but S-O group occurred on Thioox-idans ferrooxidans cell surface and the P-O group appeared on Mycobacterium Phlei cell surface, and the content of C?O?H and C?O?C groups on Mycobacterium Phlei cell surface is higher than that on Thiooxidans ferrooxidans cell surface, this also been known from UVS investigation. The affinity of these groups to metal ions on sulfide minerals is able to explain the selective adsorption.

Jan 1, 2014

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By Fathi Habashi

A new era in pressure hydrometallurgy is marked when the roasting - leaching - electrowinning process in the zinc industry was replaced by direct pressure leaching of zinc concentrate. Since then, the technology has received recognition as the technology of the future. Large autoclaves of unprecedented size have been manufactured and installed in a number of metallurgical plants for recovering copper and nickel from their concentrates or liberating gold from its refractory ores. An attempt to recover alumina from clay using pressure technology is underway. Autoclaves lined with acid resisting bricks or with titanium clad may weigh as much as 800 tonnes were transported successfully from the manufacturing workshop to the mine site over long distances.

Jan 1, 2014

By Gabriela Pino, Maurício Torem, Lorgio V. Gonzales

It has been long known that many microorganisms are able to interact with mineral particles to obtain a concentrate; thus, one possible technique is flotation and its related process. Biological process have been attracting attention in mineral processing due to lower operating cost and their possible applications to process low-grade and fine ores. The adhesion of microorganism to surface of mineral particles can alter the hydrophobicity of mineral markedly. Such surface modifications modify its hydrophobicity or hydrophilicity will be used to flotation of cassiterite fines. The major difficult to float fine particles is attributed to the low probability of bubble-particle collision, one characteristic of electroflotation process is the ability to create very tiny bubbles, which is known, improve the collision efficiency and flotation performance of fine particles. In this study, the electroflotation of fine particles using Rhodococcus opacus strain as bioreagent was investigated. Electroflotation experiments were carried out using particles of cassiterite around 8µm of mean diameter the adsorption of R. Opacus onto cassiterite particles was confirmed by Fourier transform infrared spectroscopy (FTIR), electrokinetic and contact angle analyses. The measurement of bubble size by laser diffraction showed a mean bubble size of around 26 µm, current density and bacteria concentration appear to be the main parameters affecting the mean diameter of bubbles, electroflotation tests reported recovery around of 64.5 % at pH 5, concentration of 2,87 x10¹² cells/ml (50 mg/L) and current density of 51,4 mA/cm2.

Jan 1, 2014

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014