Search Documents

By R. Marandi

The effective removal of heavy metals from aqueous wastes is among the most important issues for many industrialized countries, How ever biosorption, i.e. the uptake of heavy metals by non- living biomass, has gained increased credibility during recent years. Biosorption of Cr(VI) from aqueous solution, on pretreated and immobilized Aspergillus niger was investigated in a batch and countinuous reactors. A.niger biomass pretreated by boiling in 0.5 N NaOH solution for 15 min, exhibited higher Cr(VI) removal capacity than autoclaved biomass. The optimum adsorption pH value observed for Cr(VI) ions was 2. The Cr(VI)removal rate increased with a decrease in pH. The influence of contact time, pH, Cr(VI) concentration, biomass concentration and temperature on Cr(VI) removal were also evaluated. Biosorption of Cr(VI) on pretreated biomass followed the Freundlich and Langmuir adsorption models.In this study A.niger biomass was immobilized in Na-alginate matrix. The biomass beads packed in a column were able to remove metal ions.In this study we used two different flow rate in a column, 1.5 mL/min and 3 mL/min.The breakthrough data obtained for Cr(VI) was adequately by the Thomas and Yan models and the adsorption capacity of the biomass was found to less than the adsorption capacity obtaind in the batch study. When the beads containing biomass become saturated with metal ions, the adsorbed metals were eluted using 0.5 N NaOH solution. Therefor nearly 90% of Cr(VI) was desorbed by NaOH solution.

Jan 1, 2014

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By Ana Elisa Casas Botero

The Rhodococcus opacus microorganism was evaluated as a biocollector for flotation of barite. The electrophoretic behaviour of the mineral, before and after R. opacus interaction, was evaluated and showed that the cells adhesion shifted the mineral zeta potential curves. Adhesion tests were suggested a high affinity of the bacteria for barite. The experiments of the adsorption rate of the R. opacus on the mineral surface showed fast kinetics, achieving a maxim of cell adsorption after 5 minutes. Adsorption isotherm curves for barite could be categorized as Langmurian (L) type II. The best bioflotability results for barite achieved values around 75% for a R. opacus concentration of a R. opacus concentration of 250 ppm in the pH around 5.0. The studies were compared with the flotation of barite using a traditional collector. The bioflotation experiments were discussed considering the obtained adhesion tests. The results were supported by the Thermodynamic approach for selected pH values. The fundamental flotation studies showed the paramount potential that R. opacus presents as a biocollector and its possible application in the mineral flotation industry.

Jan 1, 2014

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By R. Marandi

Biosorption of heavy metals can be an effective process for the removal of heavy metal ions from aqueous solutions. In this study, the adsorption properties of nonliving (boiling in NaOH) biomass of phanerochaete chrysosporium. For Pb (II) and Zn (II) were investigated by using batch adsorption techniques. The effects of initial metal ion concentration, initial pH, biosorbent concentration, stirring speed, effect of temperature and contact time on biosorption efficiency were studied. Experimental results indicated that the uptake capacity and adsorption yield of one metal ion were reduced by the presence of the other metal ion. In the experiments the optimum pH value was found out 6.0. The experimental adsorption data were fitted to the Langmuir and Frundlich adsorption models. The highest metals uptake was calculated for Zn (II) and Pb (II) were 57 and 87 respectively. desorption of heavy metal ions was performed by 50 mM HNO3 solution. The results indicated that the biomass of p.chrysosporium is a suitable biosorbent for removing heavy metals ion from aqueous solution.

Jan 1, 2014

By S. J. Ma

To look into the ionic release laws of the sulphide tailings in some copper mine, the effects of the soaking period, temperature, oscillating speed, and pH of the solution on the heavy metals ionic re-lease were investigated through static soaking leaching experiments. The results show that Cu2+, Zn2+, Pb2+, Cr3+ are of different leaching behaviors with soaking period. The ionic concentration in soaking solution for four ions has a great gap. Zn2+ is more easily released out of sulfide tailings than Cu2+, Pb2+, Cr3+ , and the ion release concentrations are not proportion to their contents in the tailings. The time for each ion to reach its maximum concentration are different. The minimum concentration do not occur at the first day. Each ion concentration shows different fluctuation characteristic during soaking process. Solution pH, oscillating speed, and temperature affect the releases of Cu2+, Zn2+, Pb2+, Cr3+ out of the tailings to different extent. The effect of pH value on ion re-lease for the four ions ranks as Zn2+>Cu2+>Pb2+>Cr3+, the oscillating speed ranks as Pb2+>Zn2+>Cu2+>Cr3+, and the temperature ranks as Cr3+>Pb2+>Zn2+>Cu2+.

Jan 1, 2014

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By G. Y. Liu

The structure-activity relationships for four thionocarbamate collectors are discussed in this pa-per. These collector classes are alkyl alkyl thionocarbamates, allyl alkyl thionocarbamates, acyl al-kyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates. The main emphasis will be to highlight the differences between collectors and their affinities for copper and iron sulfide minerals on the basis of data on electronic-structure properties obtained by vacuum and solution density functional calculations, flotation experiments and analysis measurements. The mechanism of interaction of these collectors with sulfide minerals is also discussed with perturbation theory. The theoretical study results indicate that acyl alkyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates have best performance in these agents as flotation collectors with improved collecting power for copper sulfide minerals and excellent selectivity against iron sulfide minerals, which are consistent with the experimental data reported in the literature.

Jan 1, 2014

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By A. Bastrzyk

Text The mining and refining of minerals generates large amounts of solid waste. The waste from cleaning operations constitutes up to 90% of the total production. Although some of them can be used in mining, civil enegineering, construction, agriculture, most of them must be disposed in dumps and slurry ponds, causing major economic and enviromental problems (Alonso, 2002; Alon-so, 1999). The refuse from minerals cleaning may have considerable valuable particles content, which can be used in industry. Thus, the recovery of these particles from minerals waste by using a cleaning method effective at fine particle size, may overcome these consequences. Surfactants are used in numerous applications including emulsification and solid surface modification. In the oil agglomeration of minerals, the ionic surfactants (both anionic and cationic) are used for the hydrophobization of mineral surface and the oil-water emulsion preparation. When the cationic surfactant is injected into the oil-water mixture, surfactant molecules adsorb at the oil-water interface, changing droplets? properties. The addition of anionic surfactant to the mineral suspension was found to modify the solid-liquid interface. In this paper, the condition and mechanism of selective separation of magnesite from quartz are presented. A satisfactory was achieved with the amount of anionic collector (sodium oleate) equal to 15.2 mg/gsolid and with the amount of cationic collector 27.9 mg/gsolid for cetyltrimethylammonium bromide (CTAB) and 16.9 mg/gsolid for dodecyloammonium hydrochloride (DDAHCl) at pH 8. At these conditions, the amount of agglomerated carbonates was about 12% for CTAB and 5% for DDAHCl.

Jan 1, 2014