Search Documents

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Eschebach, D Mathewson

A belt press filter (BPF) handbook containing practical information for the reference of plant designers and operators has been created as part of Australian Coal Association Research Program project C23040. The handbook combines research and experience with newer generations of equipment and circuitry. BPFs are increasingly finding application in the dewatering of thickener underflow tailings slurries due to changing environmental regulations, difficulty obtaining tailings storage facility approvals and limited water availability. Sources of BPF inefficiency and low availability stem from a lack of understanding of the key operational parameters that affect their performance. This lack of understanding typically leads to increased operational expenditure due to suboptimal reagent dose rates and increased maintenance costs, or decreases in plant availability due to excessively high filter product water contents and equipment failure. It is essential for the continued economically competitive operation of Australian coal handling and preparation plants that complex factors affecting BPF operational performance are clearly defined and understood. Installation and operation handbooks are often provided to sites with new installations, but these manuals are manufacturer- or even model-specific and are often focused on mechanical maintenance. The handbook identifies industry ‘best practice’ and improvements developed by other sites, such as extra spray bars, air system bleed valves, guarding designs, feed and filtrate protection screens and roller tensioning systems. Equations to predict optimum operating conditions – such as free moisture, belt tension and reagent dose rates, with simple feed-specific variable inputs – have been developed from site-specific test work. The correlations developed provide a benchmark for plants to attempt to achieve. This provides operators and process engineers with a tool to explain BPFs and assist them in optimising the performance of BPF dewatering plants of both contemporary and less modern design.CITATION:Mathewson, D and Eschebach, D, 2015. ACARP belt press filter design, operation and maintenance handbook, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By K Williams, M Pender, T Honeyands, T Krull, D McCallum, R Holmes, R Orense

Bulk cargoes, including iron ore fines, must be shipped according to the rules agreed by the member states of the International Maritime Organization (IMO). One critical safety measure is the transportable moisture limit (T?ML) required for Group A cargoes (cargoes that may liquefy). A number of shipping incidents involving iron ore fines from India, where liquefaction of the cargo was suspected to be the cause, have brought the issue of iron ore fines T?ML into the spotlight. Extensive research has been undertaken by the major iron ore producers from Australia and Brazil to support the IMO in developing regulations for the shipment of iron ore fines. To this end, iron ore companies sponsored the AMIRA P1097 project to establish a modified T?ML test approach specific to iron ore fines. The project was undertaken by TUNRA Bulk Solids, CSIRO’s Centre for Bulk Solids and Particulate Technology and the University of Auckland, with project leadership provided by Creative Process Innovation. This program of work supported test work findings from the IMO Iron Ore Technical Working Group, which reported its findings in September 2013.The purpose of this paper is to present the major research findings from the AMIRA P1097 project, which includes a review of the original T?ML methods, highlights of the research that supported the new iron ore fines T?ML method and an outline of current iron ore T?ML requirements.CITATION:Williams, K, Honeyands, T, Holmes, R, Orense, R, Roberts, A, Pender, M, McCallum, D and Krull, T, 2015. Maritime bulk cargo transportable moisture limit requirements for iron ore shipments, in Proceedings Iron Ore 2015, pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G J. Showers, P Botman, A G. Hunt

Iron Road Limited (Iron Road) is currently evaluating the feasibility of producing 21.5 Mt/a of high-grade (>66 per cent Fe) magnetite concentrate from a 3.7 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate can be produced via a conventional grind and low-intensity magnetic separation flow sheet. Due to the comparatively coarse magnetite liberation size (106 µm), consideration was given to enhancing both the grind economics and coarser product sizing via gravity separation.This paper outlines the test work, flow sheet design and engineering design of a gravity beneficiation circuit (GBC) conducted by Mineral Technologies for Iron Road. The resulting circuit optimisation necessitated mass balance simulation by Iron Road’s SysCAD model to quantify the resulting changes in mill recirculation load. This included the determination of project-critical grinding power and energy requirements with and without the GBC installed into the primary ball mill classification circuit. The outcome of this work was the design of a GBC, including spirals and up-current classification, which led to a substantial reduction (33 per cent) in ball mill recirculating load and power requirements, together with a favourable coarsening of final product size due to the relatively coarser gravity concentrate. This has led to a significant reduction in project design capital and operating costs. A further benefit of this approach is increased recovery of (paramagnetic) hematite and lesser titano-hematite via gravity separation compared to an all-magnetic separation approach.CITATION:Hunt, A G, Showers, G J and Botman, P, 2015. Test work and design of a gravity circuit for Iron Road’s Central Eyre Iron Project, in Proceedings Iron Ore 2015, pp 139–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By I Brandes de Roos

Water has played a key role in the Pilbara’s 60-year history of iron ore operations. In contrast to many of the current-day mining environments, iron ore mining was initially hosted by geological formations that were typically above the water table. Such mining operations required no dewatering or dewatering at rates that were less than mine and mining township requirements. The challenge for these operations was not pit dewatering but water supply for mining operations and municipal supply for nascent mining towns.The current industry sees new deposit styles being increasingly targeted, including channel iron and Marra Mamba Formation deposits. These deposits are often lower in the landscape and can require extensive dewatering. Furthermore, increased water demand for ore beneficiation has resulted in major programs of water-supply borefield development. Added to this is the emergence of magnetite projects and their significant levels of water use in ore beneficiation.The large volumes of water that are being extracted to support Pilbara iron ore mining is attracting attention. The Western Australian Department of Water has recently commissioned a study to assess the potential use of surplus mine water as a medium- to long-term supply for irrigated agriculture.This paper outlines the changing landscape of water management in Pilbara iron ore operations and explores strategies for maximising mining productivity. Water management is presented as an enabler for productivity improvements that can potentially provide long-lasting benefits post-closure.CITATION:Brandes de Roos, I, 2015. Shifting waters in the Pilbara’s iron ore industry, in Proceedings Iron Ore 2015, pp 507–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By U König, N Norberg

Traditionally, quality control of iron sinter has relied on time-consuming wet chemistry. However, the mineralogical composition that defines the physical properties, such as strength or reducibility, is not monitored.X-ray diffraction (XRD) analysis in combination with Rietveld quantification and statistical data evaluation using partial least squares regression (PLSR) has been successfully trialled to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than eight minutes per sample. The results were compared with wet chemistry data.PLSR does not require pure phases, crystal structures or complex modelling of peak shapes. The analysis is therefore easy to set up and ideal if only one property needs to be analysed. PLSR results show an accuracy for the FeO content of ±0.3 per cent for the samples analysed in this case study.Both the PLSR and Rietveld methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. PLSR was found to be the more robust method if only FeO and basicity results are required. The Rietveld method helps to predict other parameters, such as the compression strength of the sinter, by monitoring all existing phases (eg larnite C2S or silico-ferrite of calcium and aluminium phases).CITATION:König, U and Norberg, N, 2015. Iron sinter process control using x-ray diffraction, in Proceedings Iron Ore 2015, pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C Pope, M Tannock

Mining exploration and development projects in Australia are being negatively affected by the highly complex regulatory and bureaucratic processes at all levels of government. These processes affect mining companies operating in Australia by impacting on timelines and the cost of developing a mining project. It is not uncommon for the granting of project approvals to take in excess of five years, meaning that mining companies struggle with productivity, efficiency, time frame and cost issues in respect to their projects in Australia. As the mining boom in Australia is moving from the investment to the production phase, it is now more important than ever to maintain a regulatory landscape that facilitates rather than discourages new investment.While one of our key arguments is that there is too much burdensome regulation and red tape in Australia, we are also strongly believe that regulatory intervention is necessary to ensure that appropriate checks and balances are in place to serve the public interest and manage environmental, health and safety, social and other development-related impacts that may arise from a mining project. However, the regulatory intervention in Australia has come to a point where it is excessive and starting to discourage valuable investment in mining projects for nominal return to the public. Excessive regulation or ‘red tape’ impedes productivity and competitiveness, deters investment and innovation and costs jobs, all of which ultimately impact on the growth of Australia and the standard of living of all Australians.This paper aims to examine and compare the federal, state and local regulations that govern mining projects in Australia. It will highlight how these regulations are unnecessarily complex, lengthy and duplicated and how they can be streamlined to reduce red tape. In doing so, the paper will evaluate the recommendations proposed by the Productivity Commission Report on Major Project Assessments released in 2013, which include the recommendation to move to a ‘one project, one assessment, one decision’ regulatory model.CITATION:Pope, C and Tannock, M, 2015. Project development and regulation red tape – a comparative analysis: does it need to be so complex?, in Proceedings Iron Ore 2015, pp 621–630 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K Williams, G M. Evans, S M. Iveson, K P. Galvin, C E. Loo

The Australian Research Council (ARC) has recently established an Industrial Transformation Research Hub in the area of iron ore, focused on iron ore characterisation, beneficiation, materials handling and end-use functionality. The research hubs are part of a new initiative aimed at building stronger relationships between industry and universities, while addressing issues of national significance. The ARC Research Hub for Advanced Technologies for Australian Iron Ore will focus its attention on developing innovative approaches for creating enhanced value across the full value chain through the characterisation of different ore types, beneficiation and materials handling and transport. This hub brings together five industrial organisations and a research team formed from well-established research groups based at the Newcastle Institute for Energy and Resources. These groups have a record of working closely with industry to create opportunities. Examples include new beneficiation technologies such as the Reflux Classifier for achieving gravity separation, the expertise of TUNRA Bulk Solids in materials handling and the Iron Making Centre at Newcastle, which is a capability maintained by BHP Billiton following the closure of its Technology Centre in 2009. The purpose of this paper is to provide an outline of the research hub and its objectives, some background on the research groups that now form the hub and an insight into the strategy adopted for developing and implementing new technologies. The paper also describes a range of novel technologies that have the potential to be developed and applied to iron ore beneficiation.CITATION:Galvin, K P, Roberts, A, Loo, C E, Evans, G M, Williams, K and Iveson, S M, 2015. Australian Research Council research hub for advanced technologies for Australian iron ore – an introduction, in Proceedings Iron Ore 2015, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Zlatev, S Silge

Producers of primary resources such as iron ore face the challenge of processing crude materials with increasing levels of impurities, which may result in the requirement for wet processing. This results in a significant increase in water usage, power consumption and operating costs. Given the remote locations of most operations in Australia (Stewart et al, 2013; Prosser, Wolf and Littleboy, 2011), the required volumes of power and fresh water for wet processing can be very difficult to achieve.HAVER&TYLER is renowned across the world for their screening technology in wet and dry processes. Its innovative Hydro-Clean® system represents a cost-effective and eco-sensitive way to clean any crude materials and material blends with a grain size distribution of 0–150 mm that are contaminated with adhesive clay, slit and other impurities.CITATION:Silge, S and Zlatev, M, 2015. Iron ore washing – achieve more with fewer resources, in Proceedings Iron Ore 2015, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015