Search Documents

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By V. Panayotov, M. Panayotova, R. Villas-Bôas

The "United Nations Framework Classification (UNFC-2009) for Fossil Energy and Mineral Resources 2009” is the international system designed to meet (to the extent possible) the needs and to support the decision making and resources management of private industry investment, governments, policymakers, bank investment, scientists. There are different international and national systems classifying commodities (resources, reserves, possibility and feasibility to extract them, etc.) with their own definitions and reporting terminology which often do not overlap entirely or even differ significantly - thus creating difficulties and problems among stakeholders to understand each other. The UNFC-2009 is developed to allow “speaking in one language”. The paper presents briefly the UNFC-2009. The UNFC-2009 applies simultaneously three fundamental criteria to classify projects: economic and social viability, field project status and feasibility, and geological knowledge (so called E, F and G axes), thus creating a visualized, easily understandable three dimensional system. The E, F and G axis categories are divided to subcategories, using additional criteria. The UNFC-2009 is already applicable to solid minerals, nuclear fuel resources, petroleum. The amounts of solid waste generated by metals production from ores (mining, minerals beneficiation, extraction metallurgy) and its metals content are discussed from the viewpoint of using the waste as resource. An attempt is made to apply the UNFC-2009 to technogenic waste from metals production from ores - both to old engineering constructions (historic mining dumps and reclaimed beneficiation tailings ponds) and new (currently in use) dumps and ponds.

Jan 1, 2016

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By Michael Gebman, Jack Gerwick

"With the opening of the new San Francisco-Oakland Bay Bridge East Span, the former bridge and its caisson foundations are being demolished. Caisson foundations are in the path of a future shipping channel and therefore need removal down to the mudline 50 ft below water (MLLW). For the first caisson to be removed (E3) a mechanical demolition was performed above the waterline and an implosion was done for the remaining caisson down to mudline. Mechanical demolition consisted of excavators operating from either on top of the caisson, from work platforms or from barges. The demolition was implemented on a trial basis with a successful implosion on November 14, 2015. The work was conducted in an environmentally sensitive area, with measures taken to protect fish, marine mammals and birds. This demolition technique was cost effective, faster to execute, and had a better environmental impact then an alternative option. The demolition, measures implemented to protect the environment, outcome, and lessons learned are presented.INTRODUCTIONThe California Department of Transportation needed a cost effective and environmentally friendly solution for removal of the remaining San Francisco-Oakland Bay Bridge (former East Span) caisson foundations, starting with caisson E3. This was necessary to clear a future shipping channel. One option was to construct a steel cofferdam around the caisson to allow demolition in the dry down to the mudline. This option would take years to complete, be cost prohibitive, and its noise would disrupt aquatic life and birds throughout the cofferdam construction and demolition. An alternative option was implemented on a trial basis to conduct a mechanical demolition of the caisson above waterline along with an implosion of the remaining caisson down to mudline. This had the clear advantage as a cofferdam was not needed, and the demolition project duration would be approximately 6 months, instead of several years for the cofferdam option. The potential impact on aquatic life and birds from the implosion was a concern, as the location is environmentally sensitive; however, measures were implemented to minimize these impacts. As presented in this paper, this demolition option was implemented on a trial basis for Caisson E3. The technique succeeded and will now be used on the remaining caissons.BACKGROUND INFO ON CAISSON E3The reinforced concrete Caisson E3 is the largest caisson which supported the former East Span of the Bay Bridge. It was constructed in 1934, with the Bay Bridge opening in 1936. Figure 1 shows the project location. The caisson had a cell arrangement of 7 x 2 above the mudline. Below mudline, the caisson had a cell arrangement of 9 x 4. A structural transition was made between the 7 x 2 and 9 x 4 cell arrangements with buttress walls. All cells were flooded, as underwater openings were included in the original caisson walls to equalize the hydrostatic pressure. Figure 2 shows the caisson layout with limits for mechanical demolition and for the implosion."

Jan 1, 2016

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By Brian T. Nereson, Michael C. Penney

"This technical paper was prepared to describe the general process by which the authors designed a column-supported load transfer platform (LTP) for support of asphalt-paved runway and taxiway embankment areas over soft organic soils, the major tasks and observations made during construction of the system, and the outcome of the system design and construction. The LTP system was designed using the method described in the BSI Standards Publication Code of Practice for Strengthened/Reinforced Soils and Other Fills, BS 8006-1:2010 (BS8006), to achieve performance objectives for the project. The design also used other criteria based upon the authors’ engineering experience and understanding of the expected interaction between soils, structures and geotextiles. The design and construction process described herein resulted in a successful project. The authors identified that full-time engineering oversight during construction was of high importance and provided a high degree of value to the project. The authors’ intimate knowledge of the potentially adverse effects of variations in construction practices promoted timely identification of construction deficiencies that could have affected the reliability of the system. This resulted in corrections and modifications being made, while materials were still accessible, to protect the intended performance of the finished system.INTRODUCTIONThe site is located in Marshfield, Massachusetts. The surrounding area is flat and contains significant wetlands with a water table at or near the ground surface. Prior to the improvements described herein, the site was already developed as an existing municipal airport with an approximately 3,000 linear-feet asphalt-paved runway oriented in a northeast/southwest direction (northeast end referred to as Runway 24 and southwest end referred to as Runway 6; Fig. 1). The site is located approximately 0.5 to 1 mile (Runway 24 and Runway 6, respectively) from the Atlantic Ocean.The improvement project included total extension of approximately 550 linear feet of asphalt-paved runways and taxiways over existing wetlands that consisted of soft, organic soils with varying but significant depths (Fig. 2). An initial geotechnical assessment performed for the project identified that the subsurface conditions were not suitable to support the proposed runways and taxiways in their existing state."

Jan 1, 2016

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016