Search Documents

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By Rolf B. Pedersen, Filipa Marques

The extension of the Mid-Atlantic Ridge north of Iceland has collectively been referred to as the Arctic Mid-Ocean Ridges (AMOR). The AMOR extends from the northern shelf of Iceland, to the Siberian shelf in the Laptev Sea, passing en route through the Norwegian- Greenland Sea, the narrow gateway of the Fram Strait, and across the Eurasia Basin. The AMOR is 4000 km long and is divided into six super segments: 1) the Kolbeinsey Ridge, 2) the Mohns Ridge, 3) the Knipovich Ridge, 4) the Molloy Ridge, 5) the Lena Trough, and 6) the Gakkel Ridge. After continental rifting at 60-50 million years ago, around 2.5 million km2 of oceanic seafloor has formed by seafloor spreading - resulting in the formation of the Norwegian- Greenland Sea and the Eurasian Basin. This northernmost part of the global ridge system is anomalous in several ways: The seafloor spreading takes place at an ultraslow rate (less than 2 cm/y) with spreading rates decreasing northward to around 1 cm/y at the Gakkel Ridge - which is the most slow-spreading ridge on Earth. As a result, the volcanic activity along the northern part of the AMOR is low, the oceanic crust is unusually thin (around 3,5 km at the Knipovich Ridge, Kandilarov et al.2010), and the rift valley is deep (average water depth > 3 km). In the southern part of the AMOR, the ridge system is affected by the Icelandic plume and a hot spot below Jan Mayen. The ridge-plume interaction results in higher volcanic productivity, unusually thick oceanic crust (9-11 km, Kandilarov et al. 2012) and shallow ridge segments (1500-100 m). The AMOR also display contrasting spreading regimes, whereas some super segments are dominated by orthogonal spreading (Kolbeinsey and Gakkel Ridge) others are characterized by highly oblique spreading (Mohns and Knipovich ridges). Some ridge segment displays asymmetric spreading, like the Mohns Ridge where core complexes preferentially form along the northwestern flank. Together these variations in ridge characteristics results in large diversity of hydrothermal systems and associated mineral deposits.

Jan 1, 2018

By J. Castaneda, J. Schmidt

"INTRODUCTION Chino is an open-pit copper mining complex faced with intricate material routing requirements. Historically, this was challenging at the mine, in part because the shovel dig plan, haul plan, and dump plan were prepared completely separately. The mine now uses an integrated workflow for faster evaluation of schedules, which facilitates preparing balanced cutoff grade-to-equipment requirements, supports better mineral production, and improves schedule viability, while considering operational implications. Located in the state of New Mexico, Chino is one of nine Freeport-McMoRan mining operations in North America. This presentation discusses the benefits of implementing an integrated approach to tactical mine planning, and shares practical examples that were learned as Chino implemented an integrated tactical planning method. This includes improvements in completion time for preparing a schedule, minimal risk from manipulating Excel macros, data integration required to make short-term planning decisions, and better understanding of the mine plan’s effect in relation to the business’s key performance indicators. Ultimately, the integrated approach to tactical mine planning at Chino has led to production forecasts which are more achievable and reduced planning and execution variance. PROJECT OVERVIEW Chino mine is a porphyry copper deposit wholly owned by Freeport-McMoRan, the largest publicly traded copper producer in the world. Chino mine is located in Grant County, New Mexico, a short distance east of Silver City. Ore material mined from the pit today includes oxides, primary sulfides, and secondary sulfides. The mineralized material is sent to a mill, with a rated throughput of 42,000 tons per day, or to ROM leach pads with variable dumping capacities. At Chino, the short-range objective is to maximize total copper pounds sent to the mill, but no fixed cutoff grade accomplishes this for all periods. Instead, 12 different material classifications, including four sulfide classes that can feed either the mill or other destinations, and 38 cutoff bins, are aligned with the needs from operations, leaching, and the concentrator to create a schedule. Cutoffs vary from one week to another to cope with a highly intermittent ore body."

Jan 1, 2018

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By Siobhan Quayle

Managing sediment plumes under multiple jurisdictions Management of activities in the New Zealand EEZ can be characterized as a distributed basis of decision-making with each independent and separate decision-maker focused on specific elements of a proposal (environmental, work place safety, wildlife management, fisheries, navigation, oil spill). The New Zealand EEZ Act 2012 was intended as gap-filling legislation to address the lack of an environmental assessment lens for permissions to undertake certain activities in the New Zealand EEZ. These activities relate mostly to marine scientific research, dumping and discharges, oil and gas exploration and development, and seabed mining. The regulatory decision-maker for most EEZ Act marine consents is the New Zealand EPA. Since 2013 when this gap-filling legislation took effect, the EPA and its decision- making committees have processed three seabed mining applications. Two consents were refused, one consent was granted in 2017. A common feature of all consents has been the assessment and consideration of the scale, significance and effects of sediment plumes arising from the activity. One consent is for irons and mining in about 40m of water where the plumes reach the nearby coastal waters and shoreline, the second consent is far offshore but plumes extend far beyond the mining area (850 km2) in to rare coral habitats and in to a significant offshore fishery. A significant consideration for decision-makers is how the assessment and management of plumes under the EEZ Act interact with, and potentially overlap, management of such plumes under other legislation (Resource Management Act, Marine Mammals Protection Act, and Wildlife Act). This is in a statutory context where the EEZ Act requires explicit consideration of the nature and effect of other marine management regimes over the matter under consideration.

Jan 1, 2018

By T. Bauerle, G. Poplin, Z. Dugdale

"The issue of mine worker fatigue is as complex as it is understudied. Generally, worker fatigue lies somewhere on a continuum between psychology and physiology, which makes the measurement and management of it difficult with no easy solutions for operators or workers. Answers to even basic questions remain elusive—such as what is fatigue, how is it measured, and how can organizational resources reduce fatigue—and answers seem to present no single, clear path to action for the health and safety of the worker. This manuscript supplements the growing body of interest in the problems of fatigue in the mining industry by reviewing some of what is known about worker fatigue in general and in the mining industry in particular. The material covered here includes basic topics of the hows and whys of worker fatigue; an overview of fatigue models, findings, and evidence-based solutions with a focus on mining; and potential future directions aimed at mitigating miner fatigue. INTRODUCTION “It is recommended that the whole fatigue test problem be stated in a form the nature of which may be indicated by the following suggestions: that the term fatigue be absolutely banished from precise scientific discussion, and consequently that attempts to obtain a fatigue test be abandoned [emphasis added].” – Bernard Muscio, Pioneer Australian Philosopher and Industrial Psychologist, in a 1921 Report to the Cambridge Industrial Fatigue Research Board Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work, or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetative duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising. On the one hand, mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation, and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a “cookie-cutter” approach. On the other hand, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present alltogether. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining."

Jan 1, 2018

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

By Venkataramana Runkana, Pradip Gautham, Beena Rai, Sreedhar Reddy

"IT enabled platforms are the key to provide an integrated view of the business activity or an enterprise as a whole. Attempts to integrate all functions in an enterprise such as mine-to-market initiatives, wherever and to whatever extent implemented, have provided significant benefits to the industry. The transformative potential of IT enabled integration platforms is illustrated in this communication from our own work in this field. TCS PREMAP (Platform for the Realization of Materials and Products) is a knowledge-driven engineering design and development platform which leverages modeling and simulation and artificial intelligence into the engineering design process. We illustrate the customization of this generic platform for the design and optimization of mineral processing plants in an integrated manner. TCS PEACOCK (Process and Equipment Analytics for Optimization and Control) has been developed to enable automation of data analytics in the operating plants. We illustrate its utility and power in improving the plant performance with the help of case studies from our work on pelletization of iron ores and optimization of flotation plants. INTRODUCTION We are living in an exciting digital era. With the advent of cloud computing and social media on the one hand and rapid advances being made in several research areas of interest to us in the minerals and metals industry such as artificial intelligence (AI) & machine learning, robotics, unmanned vehicles including drones, big data analytics, 3D printing, sensor technologies, renewable energies and internet of things (IoT), many disruptive transformations in our industry are on the horizon. Recent advances in information technology (IT) and knowledge engineering, in combination with appropriate domain expertise, that is, our enhanced understanding of the underlying science of mining and mineral processing operations and the availability of a variety of powerful modeling-simulation tools make it possible to address the challenging problems facing the mining and mineral processing industry, in an integrated manner."

Jan 1, 2018

By A. Ang-Ug, L. Gurieff

"The Phu Kham Cu-Au mine in Laos is owned and operated by Phu Bia Mining Limited. The deposit is a complex and low grade Cu-Au porphyry ore. The rougher feed has a particle size distribution of 80% passing 110 µm, and the rougher concentrate is reground for cleaning to 80% passing 25 µm. The Cu losses in the cleaning circuit are primarily in the <12 µm fraction. A randomised paired ON-OFF test of magnetic conditioning in one of the two parallel cleaner 1 circuits was undertaken. The results showed that with magnetic conditioning there was approximately a 10% reduction in the <12 µm Cu distribution in the cleaner 1 tail to a 98% level of confidence. The Cu distribution in the <12µm fraction is a less variable measure of changes in the <12µm Cu recovery, therefore, this was used to evaluate the impact of magnetic conditioning. Subsequently, magnetic conditioning was installed in both cleaner 1 circuits and the plant results monitored after this installation. Comparing the plant results immediately before and after this installation showed that there was a 20% reduction in <12µm Cu losses to the cleaner tail. INTRODUCTION The Cu-Au, Phu Kham Mine (PKM) is located within PanAust's Phu Bia Mining Contract Area in Laos, approximately 140 kilometres from the capital city, Vientiane. PKM is PanAust's flagship operation and the significant cash flow generated by PKM has supported PanAust’s growth, while contributing to a strong balance sheet. PKM comprises an open-pit mine and a conventional milling and flotation operation that produces and exports a Cu and precious metals concentrate. The concentrate contains around 23% Cu, 6 ppm Au and up to 35 ppm silver. Process Overview The PKM deposit consists of complex heterogeneous mineralogy horizons of Cu-Au stockwork and skarn mineralisation. It contains areas of soft-leached zones, overlying transition zones and supergene chalcocite dominant secondary Cu mineralisation and clay-rich gangue. Areas of high As and Zn also pose a challenge in treating the highly variable ore. In addition, hardness of the ore increases with deposit depth. The ROM is hauled to a primary gyratory crusher to produce a coarse ore stockpile with size distribution suitable for the 13 MW semi-autogenous mill. The SAG product feeds two parallel ball mills each equipped with a cyclone cluster producing a product particle size distribution of 80% passing 110 µm. The conventional flotation circuit consists of two parallel rougher banks. The rougher concentrates feed the regrind cyclone where the underflow is split and reports to two parallel, 3MW, M10000 IsaMills. The regrind mill discharge combines with the regrind cyclone overflow with a product particle size distribution 80% passing 25 µm and reports to the Jameson cell."

Jan 1, 2018

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By C. H. Veloso

"Starch is the most widely used depressant in the reverse cationic flotation of iron ores. There is however, an indication from recent studies, that other polysaccharides may successfully replace them. When starches are used in the flotation of iron ores in the presence of quartz as gangue mineral, their strong adsorption on the surface of iron oxides can be explained by the molecular conformation between the available sites on the mineral surface and two hydroxyls of starches. However, when the gangue minerals are iron-bearing silicates, the strong interaction with starch can occur on these minerals since they have the same surface behaviour as iron oxide. In this work bench scale tests were conducted in order to generate scientific knowledge about other alternatives depressants for the flotation of iron ores. A magnetic pre-concentrate from a skarn iron ore processing plant was used as feed material for flotation tests. The reverse flotation approach was used to upgrade the iron content by removing complex ironbearing silicates. The depressants used in this study were: corn starch, dextrin, carboxymethyl cellulose (CMC) and humic acid. The tests were performed under different pH conditions in order to try to relate the efficiency of depression to the pH used during flotation. The results show the important role of pH as each depressant reached its best performance at different pH values. At alkaline pH the corn starch showed best depression performance while the humic acid is more efficient at pH close to neutrality.INTRODUCTIONIron corresponds to approximately 6% of earth’s crust composition (McDonough and Sun, 1995). It is the most used metal in our lives, some of its properties as resistance and facility to be shaped makes is replacement very difficult. The primary sources of iron on our planet are minerals. The iron-bearing minerals most commonly found in nature and economically exploited are magnetite [Fe3O4], hematite [Fe2O3], goethite [FeO(OH)] and siderite [FeCO3] (L O Filippov et al., 2014). These minerals are commonly associated with other minerals (most of the time not economically exploited) forming the so-called iron ore. Iron ore is the source of primary iron for the world’s iron and steel industries."

Jan 1, 2018