Search Documents

By Mark Johnson, Mathew Janes

"The Resonator RD 260 Resonant Pile Driver delivers ground disturbance free, high production pile driving. The Resonator has recently been used on numerous production pile driving sites in the Netherlands and Melbourne, Australia to drive piles in sensitive areas where conventional pile drivers could not be used. Two case histories are provide in this paper which demonstrate the features and benefits of Resonant pile installation.. In the Netherlands the Resonator RD 260 was used at the Vopak Oil Storage facility in the Port of Rotterdam to install pipe and sheet pile within an active pumping gallery. The site demanded vibration free pile installation to construct a cofferdam within sensitive, highly valued assets. Access was an issue and schedule demands were stringent as shutdown windows were narrow. The RD 260 provided ground disturbance free piling immediately adjacent to fragile structures. At Vopak the only site access was using a large crane positioned over 40 m from the location of pile driving. Driving was conducted amongst 900 mm dia pipes carrying heated crude oil.In Melbourne the RD 260 was used to drive GU 18 sheet piling adjacent to light rail easements. The project was the first of many grade separations being constructed within Melbourne urban areas to lower the light rail and provide quieter rapid transit. The original trial used an RGT MR105 series vibrator but noise and vibration criteria were exceeded. The RD 260 was brought in for a trial and performed with high production and produced negligible ground vibration. Up to 17 sheet piles 14 m in length were driven in a 2.5 hour window during the trial.IntroductionThe Resonant Pile Driving method is gaining acceptance around the world as a new method to rapidly drive piles free of ground borne vibrations. The high frequency vibrator resonates the pile, essentially turning the pile into a spring, to excite the toe of the pile with high accelerations and low amplitude. High acceleration with low amplitude generates high penetration rates but the high frequency stress waves are quickly dissipated in the soil. Typically ground borne vibrations are measured at below 1 mm/sec within 1 to 5 m of the pile. The Resonant method can drive a pile next to a glass of wine, without spilling, as has been demonstrated on numerous piling sites.How Does Resonance Work?The Resonant method uses a hydraulic piston - cylinder geometry to generate high magnitude, high frequency oscillating force. This is a very different mechanism than the eccentric mass technology used in conventional and variable moment vibrators.A unique valve geometry achieves the high frequency flow switching necessary to oscillate the hydraulic piston at up to 180 Hz (10800 VPM). The valve is controlled electronically for maximum accuracy of the desired frequency. The volume of hydraulic oil delivered through the valve to the piston (flow rate) determines the amplitude while the hydraulic pressure determines the peak force."

Jan 1, 1900

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By Zaw Zaw Aye, Sereyroath Chea, Nutthapon Thasnanipan, Thayanan Boonyarak

"As there are only limited numbers of bored pile constructed in sandstone and siltstone in Thailand, load transfer and settlement behavior of a pile in these rocks are still not fully understood. Major factors which influence the performance of the pile in the sedimentary rock should be systematically investigated. The objective of this paper is to analyze load distribution and load-settlement behavior of bored pile in sedimentary rock. Interpreted data was obtained from instrumented load testing results of large-diameter bored piles. These piles were drilled in aeolian soil and socketed in sandstone or siltstone, having socketed length varying from 1 to 3 times the pile diameter. Factors that influenced pile settlement behavior, consisting of rock type at the pile base, socket length, at-rest earth pressure and rock conditions, were analyzed. For interpretation of results, analytical solutions were used to estimate load bearing capacity and calculate settlement of each pile. According to test results of mobilized unit skin friction in siltstone, relationship of 0.1 – 0.3 square root of the unconfined compressive strength of rock appears to reasonably capture the measured shaft friction. Note that shaft movement in siltstone layer was not fully mobilized as maximum pile head settlement was still less that 1% of the pile diameter.INTRODUCTIONExtensive research of bored pile construction in soft soil in Thailand and Myanmar (Boonyarak et al., 2016; Aye et al., 2015) has been carried out. However, behavior of bored pile in weak rocks such as sandstone and siltstone is still not fully understood. Unit skin friction and unit end bearing of piles in these weak rock were reported by Horvath et al. (1983) and Pells and Turner (1980), respectively. Further research is still required to minimize variation in data presented in their study.This paper presents interpretation of load testing results of instrumented piles. These piles were excavated in aeolian deposit in the Northeast Thailand. Some piles were socketed in sandstone or siltstone. Analysis results of load-settlement, shaft shortening, pile settlement estimation, factor for calculating shaft friction and end bearing are reported. Discussion and explanation of pile behavior in sandstone and siltstone is provided.BRIEF INFORMATION OF THE PROJECTProject locationsThe construction sites are located in Khon Kaen and Nakhorn Ratchasima Provinces in the Northeast Thailand. Bored piles in this project were designed for supporting elevated structures for railways, overpasses and U-turn bridges for vehicles. These overpasses and U-turn bridges are distributed along the existing railways with the distance of about 180 km."

Jan 1, 1900

By Anthony T. C. Goh, Zhiye Zhao, Laddu B. Jayasinghe, Hongyuan Zhou, Yilin Gui

"Ground vibrations from blasting are undesirable and they are very short in duration with high principal frequencies and high amplitude. Structural response to that kind of excitations may differ significantly from that generated by lower-frequency earthquake vibrations. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. However, the existing vibrations limits are not always applicable, as they depend on the geological conditions of the site and the dynamic characteristics of the structure. This paper investigated the influence of the rock-soil interface on the response of pile foundation to ground-borne vibration from rock blasting, through numerical simulations using finite element software LS-DYNA. It is found that the slope of the rock-soil interface greatly influences the location of damage and the extent of damage on the pile. The bottom of the pile is subjected to a larger blast pressure and stresses are highly concentrated at the pile bottom. Thus, the pile bottom can fail in shear before it reaches its plastic moment capacity.INTRODUCTIONDrilling and blasting is the widely accepted method to large-scale rock breaking activities in civil engineering constructions due to its cost effectiveness, higher efficiency and ability to break hard rock. However, ground vibrations from blasting are undesirable and it can cause damage to nearby structures. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. The existing vibration limits are not always applicable, as they depend on the geological conditions of the site and dynamic characteristics of the structure.Pile foundations are commonly used as foundations of high-rise buildings and bridges to transfer the heavy loads from the superstructure above through weak compressible soil strata into deeper, competent soil layers which have adequate capacity to carry these loads. In engineering practice, many piles are normally designed to carry mainly vertical loads and very little lateral loads, as typically the vertical loads (the gravity) are significantly larger than the horizontal loads such as wind loading. However, in recent years, there have been a number of reported case studies of translational soil movements that have induced stresses and bending moments that have damaged pile foundations and in some cases resulted in collapse of the superstructure. Typical lateral load include nearby construction activities such as an excavation for a basement or slope, the construction of a road embankment or a tunnel, as well as earthquakes (Abdoun 1997; Goh et al. 1997; 2003; Chen et al. 1999; Dobry et al. 2003; Boulanger et al. 2007; Black et al. 2007)."

Jan 1, 1900

By Paul A. O’Brien, Gary A. Chapman, Thomas G. Cuniowski

"The new Amcor B9 paper mill in Botany, NSW, Australia, involved the design and construction of a new paper mill founded within the Botany Basin Sediments. There were numerous design and construction challenges to address, including tight settlement tolerances for the paper machine footings (6 mm total and 1/2000 mm differential limits), high variable and cyclic loads, deep (>25 m) bedrock and uncontrolled fill material across the site. The mill structure design incorporated a deep driven precast and CFA piled foundation solution, with a comprehensive swathe of testing to validate pile capacity and expected settlements. The pile design for the mill structure included the installation of approximately 1000 piles, with pile testing comprising dynamic testing and a static load test on precast piles. With consideration of Sydney’s increasing demand for development space in relative close proximity to the city’s CBD, industrial areas in the Botany Bay area are likely to make way for heavy or complex commercial and residential structures. Therefore, a better understanding of the engineering behaviour of sediments underlying these areas would allow for efficient foundation solutions. This paper presents a discussion on effective foundation testing techniques and the effects that the behaviour and characteristics of the Botany Bay sediments impose on deep piled solutions.2 PROJECT DETAILS2.1 New paper millThe project involved the construction of the largest recycled paper machine in Australia. The paper machine is 330 m (1080 ft) long, 22 m (72 ft) high, and capable of producing 1.6 km (1 mile) of paper per minute. Construction commenced in early 2011 and new paper mill officially opened in early 2013. The early works contract was awarded to Baulderstone Construction Pty. Ltd. (Lend Lease Corp. Ltd.), with the D&C contract awarded to a consortium headed by Leighton Contractors Pty. Ltd. (CPB Contractors Pty. Ltd.), which included Golder Associates Pty. Ltd. as the geotechnical designer and reviewer.2.2 Site history and effect on local topographyThe site has been used as a paper mill since 1902, and as such, has layers of uncontrolled fill and buried objects within the upper fill materials associated with historical industrial use. The fill material generally comprised of loose and very loose sands, with isolated pockets of cohesive materials, peats, pulped paper and general construction waste. In addition, during construction, underground storage tanks were identified at depth, indicating the historical extent of filling across the site was extensive. The presence of this generally uncontrolled fill was a factor for determining that the most cost effective foundation solution for the paper mill was piled foundations, to bypass these materials."

Jan 1, 1900

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By Franz-Werner Gerressen

"New developments are required day by day. On the one hand site to improve the actual situation, on the other hand site to create the future and to ensure that future demands can be fulfilled. This requires for instance the development of technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. That means not only the three well known dimensions (width, height, depth) are cover, but also the dimension of time and money. Beside small, but important, details, also the demand of extending the use of methodologies in terms of getting deeper or allow their use in various soil conditions require the development of new tools and equipment. Therefore, the paper will describe some of these new approaches and activities required for these new developments. It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONNew developments are required day by day. Either to improve the actual situation, or to create the future and to ensure that future demands can be fulfilled. Therefore, there is an increasing demand for the development of e.g. “Little Helpers”. “Little helpers” are for example technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles, for example an assistance system like the later explained “drilling” assistant. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. In a second part the focus will be given to new approaches for soil mixing application. Adjustments of tools or equipment to extend the range of possible usage as well in terms of soil conditions as in treatment depth.“LITTLE HELPER”GeneralThe B-Tronic System enables you to efficiently operate, maintain, and administer individual machines as well as entire fleets. It helps you to securely monitor and precisely evaluate your projects and work processes. The system is an integrated system for controlling all operations and visualizing actual operating parameters in real-time on a large interactive touch-screen monitor."

Jan 1, 1900

By Andrew Middleton, Mick Stadter, Chris Crowe, David Chong

"The Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line in the south east suburbs of Melbourne. The works involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil was removed. The project has presented significant geotechnical challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. These challenges included temporary and permanent wall stability, foundations, earthworks and dewatering. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community and meet the project timeline.INTRODUCTIONThe Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line where it crosses North Road in Ormond, McKinnon Road in McKinnon and Centre Road in Bentleigh.The project involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings will accommodate three lines of rail tracks with the cuttings up to 25 m wide. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil has been removed.The project presented significant challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community. The geotechnical challenges generally fell into one of three areas, earthworks, structures and groundwater. The primary earthworks challenge for the project was moving the 250,000 cubic metres of soil in a 10 day window, however, from a geotechnical viewpoint, obtaining a stable subgrade on which to operate the necessary construction plant in a short time frame with constrained site access and time to import materials was the key. Whilst closely watching the performance of the dewatering system, a range of contingency plans were developed to cope with any difficulties."

Jan 1, 1900

By Alexander Scheuermann, Martin D. Larisch, David J. Williams

"Drilled displacement piles (DDP) have been used around the world for decades as foundation elements for structures and embankments. Typically the pile toes are designed to penetrate into stiff or dense soil formations to achieve sufficient base resistance. Recent research at The University of Queensland in Brisbane, Australia has discovered that the in situ stress conditions in stiff to hard clays is directly related to pile installation rates, which in turn are a function of the piling rig capacity and ground conditions. With adequate and constant pile penetration rates in situ stress conditions in the stiff to hard clay are increased by about 40%, resulting in significantly higher pile capacities. If pile penetration rates are too slow the in situ stress conditions are reduced considerably by remoulding and shearing of the clay, potentially causing reduced pile capacities. The paper presents the results of full-scale test piles at a stiff to hard clay site installed using different full-scale piling equipment.INTRODUCTIONDrilled displacement piling (DDP) is a piling technique in which a hollow stem, fitted with a purpose built displacement tool at the bottom, is drilled into the ground. Dissimilar to non-displacement piles, like Continuous Flight Auger (CFA) piles or conventional rotary bored piles drilled with kelly bars, the soil is not excavated during the DDP penetration process, but is displaced laterally and to a lesser extent vertically. The cavity created by the drilling tool is filled with highly workable concrete during the extraction process. The DDP technique is very economical providing high production rates and creating only marginal drill spoil, which has led to its increased global usage during the last decade. The typical DDP installation process is described in Figure 1."

Jan 1, 1900

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Jonathan G. Cannon

"This paper will describe dynamic pile testing conducted during installation of driven octagonal precast prestressed concrete piles used as the foundation for this bridge. The piles were long and hence spliced. A number of the piles showed damage near the splices and the damage location was near the ground surface so that the damage could be verified using visual inspection. The piles and splice configuration are still in use today without modification. Further WEAP driveability analysis has been conducted which demonstrates the effect of the splice on pile stresses and a likely failure mode. A slight modification is proposed to the splice that should prevent the damage on future projects.INTRODUCTIONThe bridge site is located on the Olympic Way, Route 41, about 20km north of the regional centre of Albury, NSW. For a long distance north of the site the Olympic Way ""shadows"" the main Melbourne to Sydney rail line and is located on the Western side and in close proximity. At the bridge site there was previously a sharp dog-leg in the road and a right angle level crossing with the road changing to the Eastern side of the rail line, eventually joining up with the Hume Highway, which in turn now becomes a ring-road through the eastern outskirts of Albury. The dog-leg and rail crossing had warning signs and bells, speed restrictions and rumble strips to warn approaching motorists to reduce speed. Site distance was exceptionally good.Approximately 2years before construction a group of five ""high spirited"" young men from the local area were driving south on the Olympic Way adjacent to a south-bound train. It is understood they interacted with the train crew for a period of time. Unfortunately the car and train collided at the level crossing and all of the young men were killed. There were outpourings of grief in the local community and a decision was made to replace the level crossing with a road-over-rail bridge.The bridge was highly skewed with two piers and two high level abutments with fill embankments on both approaches.GROUND CONDITIONSThe site is open grazing country with approximately level ground at the site with surrounding low hills. The geology was unremarkable with consistent stiff clays for a considerable depth.The design required driven precast prestressed pile foundations with the piles to be driven to a considerable depth.Hard driving with high tension stresses were evident from the start of driving and a variety of different pre-bore lengths were adopted in an attempt to minimise driving and potential for damage. At the abutments the pile locations were predrilled for at least the full embankment depth.PILESThe piles were 550mm octagonal prestressed concrete with the pier piles being single piece and the longer abutment piles being two-piece with a ""standard"" epoxy glued box splice. Pier piles and the initial length of the abutment piles were 24m. The add-on piece used at the abutments was 12m. Pile concrete was grade 50MPa."

Jan 1, 1900

By Gilbert Chuah, Peter Middendorp, Joost Bakker, Soon-Hoe Chew

"The Rapid Load Testing (RLT) of foundation piles has been applied worldwide since 1984. Several International and national codes are available, such as the Japanese Code of Practice (2002), ASTM D7383-2010, German recommendation on Piling (2012) and Eurocode (2015). RLT methods like Statnamic and StatRapid are gaining popularity in Asia, Europe and North America. For checking the performance of piles, they are more economical, faster and environmentally friendly than Static Load Testing (SLT), while yielding good correlations with SLT results through an objective analysis method. To date (October 2016) hundreds of piles have been successfully tested by RLT method in Singapore. A number of these RLT tests were coupled with static load testing correlation tests, some of them with instrumentation for shaft load transferred. Examples of some correlation results for foundations installed in various geological formations in Singapore are presented in the paper. The findings from these results indicate that loading rate effects are negligible for Rapid Load Test results when foundations are socketed in competent non-cohesive soil layers and derive most of their capacity from these soil layers.INTRODUCTIONRapid Load Testing (RLT), by which a quasi-static load is applied to a foundation pile, is used increasingly as an alternative to Static Load Testing (SLT) for cast in-situ piles, such as drilled shafts or bored piles. It is recognized nowadays that the determination of the pile capacity with Dynamic Load Testing (DLT) through signal matching techniques such as CAPWAP, TNOWAVE and AllWave-DLT, yield a wide spread of results for cast in-situ piles (Stahlmann et. al, 2012), making it practically very difficult, if not impossible to calibrate the DLT results with SLT results. This spread is due to the empirical and subjective assumptions that are used to interpret the test data, especially for cast insitu piles (Holeyman et al. 2001, Viana da Fonseca in 2008, Herten et al, 2013). This is further complicated by the inhomogeneity of the concrete and variable cross-sections over the pile length for the cast in-situ piles."

Jan 1, 1900

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Darren S. Diehm

"Construction for the restoration and expansion of 102-year-old Wrigley Field in Chicago, Illinois began at the conclusion of the 2014 baseball season. This six year project involves structural upgrades to the Stadium, improvements to the facade, infrastructure, restrooms, concourses, suites, press box, and bullpens, as well as the addition of restaurants, patio areas, batting tunnels, video boards, an adjacent Office-retail Tower and a new Hotel. The Bleachers were demolished and replaced, and a new underground Clubhouse was constructed for the Chicago Cubs beneath a new open-air Plaza. The 1060 Project is privately funded, projected at $750 million (US). The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience.The 1060 ProjectAfter purchasing the Chicago Cubs baseball team in 2009 from the Tribune Company, the Ricketts family began planning the renovation and improvement of Wrigley Field and its near neighborhood surroundings in Chicago, Illinois. What came to be known as the 1060 Project was officially announced at the annual Cubs Convention in 2013. Construction began on the $750M privately funded project in October 2014 at the conclusion of the Major League Baseball season. In their vision, the Ricketts committed the 1060 Project to three primary goals. First and foremost as a MLB franchise, the work should provide a meaningful contribution toward winning the World Series and ending the championship drought which stretched to the last win in 1908. Second, the project should be focused on preserving and improving Wrigley Field. Finally, the project should be committed to outcomes that enable the team to be a good neighbor and provide economic and social benefit to the local community.Constructed as Weeghman Park in 1914 for an estimated total cost of $250,000, the stadium provided seating for 18,000 fans and a home for the Chi-Feds and Whales of the National Federal League. The Chicago Cubs were enticed to move from the West Side Grounds in 1915. In the next 100 years, the Wrigley Field would be sliced apart and expanded, double its seating capacity with the addition of double deck grandstands, be enclosed by bleachers (and an ivy covered wall), and, in 1988, experience its first nighttime baseball game with the addition of lighting.The 1060 Project has a total budget of $750M, with an expected construction value of $350M. It is projected to add over 2,100 jobs to the economy and be completed before the 2020 baseball season. The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience."

Jan 1, 1900

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By S. F. Emmons

Jan 1, 1899

By J. F. Lewis

Much has been written on this great engineering work, principally from the civil engineer's stand-point. In presenting the subject to the Institute, it seems necessary to include something of geology as well as engineering. In this case, it is particularly the glacial and post-glacial periods with which we are concerned; for it has been clearly proved that the canal recently excavated has not for the first time opened the Des Plaines valley for drainage away from Lake Michigan, and that this valley, as well as the site of this city, is very closely connected with the processes and effects of the ice period. We have simply renewed a channel and a drainage direction which formerly existed. As the days of deep water-ways for commercial purposes are fast approaching, engineers may find the consideration of ancient topography and geologic changes highly useful. For what I may say on this subject I am greatly indebted to Mr. Ossian Guthrie, who has made an earnest study of glacial geology and labored especially to decipher the records of its history in this region. * Chicago is situated in the track of one of four great glacial ice-streams that swept down from the North: one moving due South from Marquette and entering the Illinois valley at Ottawa; one through the Lake Michigan valley, entering the Illinois valley near Lemont; one from Saginaw Bay diagonally across the States of Michigan and Iadiana, entering through

Jan 1, 1898

Prof. A. Ledebur, Freiberg, Saxony :* Mr. Sauveur has presented and enriched with original observations a valuable summary of the theories advanced hitherto concerning the hardening of steel; but in one particular, it seems to me, his statements call for correction. He says:

Jan 1, 1898

Robert T. Hill, Washington, D. C.: Having studied very minutely the geology of the district referred to by Prof. Branner, I beg to state that his quotation of my classification of the Cretaceous deposits of Arkansas is not the one which I originally gave,* nor is it the one which has since been published and is now generally accepted.? I did not assign ally of the Cretaceous formations of Arkansas to the " middle Cretaceous,"

Jan 1, 1898

HENRY A. VEZIN, Denver, Colo. (communication to the Secretary, February, 1897): I have read Mr. Austin's paper with considerable interest, more especially as the designing and study of such works have been an attractive occupation for me during the last twenty-five years. Mr. Austin says that a " plant on a terraced site has generally been considered the most advantageous," and also that " many advocate a level site," while he himself " is disposed to advocate a modification of the latter plan, utilizing an extended surface with a moderate slope."* Among the advocates of the terraced sites as against level ones, I do not recollect ever meeting a metallurgist who had even made an attempt to plan his works for level ground, or who had, in a lucid interval, figured how much he gained or lost by one or the other method. The average metallurgist starts with the assumption that it is rational to conduct his material down hill because its movement is aided by gravity, while to elevate ore or furnace-material by machinery he vaguely believes to be not alone wrong in principle, but also unnecessarily expensive. Let us look into the expense of elevating and see whether it really is prohibitory of the successful operation of smeltingworks on a level site. Hoisting or elevating material in the

Jan 1, 1897