Search Documents

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By F. A. Rutledge

The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively prospected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941. The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program. The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.

Jan 1, 1948

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By Frank H. Macpherson

When it became apparent early in 1941 that the United States might be drawn into the war, studies were made of the bauxite situation in Arkansas, principally because 9.5 pct of the known bauxite reserves of the country were located in that State. Bauxite mining was then geared for maximum production to supply ore to meet this country's war requirements and, if necessary, to supply the needs of Canada as well. In view of the comparatively small bauxite reserves, Congress appropriated funds for an extensive exploratory drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. An alumina plant was erected near Bauxite and an aluminum plant near Hot Springs, Ark., by the Defence Plant Corp. The Metals Reserve Co. established a schedule of prices, arranged for stockpile sites and a buying agency. Operators cooperated to step up production and new ones came into the field. Production Record Prior to 1941, the greatest annual production in Arkansas was 562,892 long tons, dry basis in 1918. During the single month of August 1943, 693,596 long tons were mined—130,704 tons more than for the entire year of 1918. In general the Arkansas bauxite deposits are relatively small, irregular in thickness, somewhat scattered and, compared to coal, iron or open-pit copper deposits, are ill-adapted to an expansion in output. Commercial deposits range in horizontal extent from less than an acre to about 40 acres and are usually very irregular in outline. The average thickness of all known workable deposits is between 12 and 15 ft. with a maximum of about 60 ft. The ore bodies are usually somewhat undulating and nearly horizontal although locally some deposits dip as much as IS°. Types of Bauxite Three physical types of bauxite may be recognized: pisolitic, granitic and amorphous. Pisolitic ore is the most common type. It consists of small pebble-like nodules, ranging from the size of a pin head up to several inches in diameter, all set in a fine grained matrix. Transported bauxite is usually- pisolitic. Most residual bauxite is granitic. It is believed not to have moved appreciably from the location where it originally was formed. This is indicated by the fact that it appears to grade into unaltered nephelite syenite, which it overlies. Amorphous ore is the least abundant. It is nonpisolitic and resembles clay, has no characteristic texture, and can be identified definitely only by chemical analysis. Uses of Bauxite Bauxite is chiefly used for, and at the present time is substantially the only

Jan 1, 1948

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By Robert L. Thorne

Cassiterite deposits on Sullivan Creek in central Alaska were investigated by the Bureau of Mines in the spring of 1943. Gold miners in the area have been recovering cassitorite each season as a byproduct of gold placer operations. Approximately 300 tons of tin concentrates have been shipped from the district. The deposits were sampled though trenches and small shafts. An average tin content of 0.28 pound per cubic yard was indicated. A detailed description of sampling methods and sample analyses is presented in this report.

Jan 1, 1948

By Donald F. Reed

The bauxite deposits of Tippah and Benton Counties in northeastern Mississippi were developed by drilling as a part of the investigation by the Bureau of Mines of the domestic sources of supply of aluminum. The primary purpose of investigations of this nature was to provide essential information to the war agencies of the United States Government and to assist owners and operators of mining properties in the production of minerals vital to the prosecution of the war. These reports are based upon the field work of the Bureau of Mines and upon data made available to the Department from other

Jan 1, 1948

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By M. Howard Berliner

During the spring of 1944, the Bureau of Mines investigated the Crescent mine area near the village of Rewey, Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau of Mines completed 24 churn-drill holes in an area immediately to the west of a mineralized section which had been mined through shallow workings for lead and zinc more than 40 years earlier.

Jan 1, 1948

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By S. P. Holt

The Rush & Brown mine has been one of the most consistent small producers of copper ore in the history of Alaskan mining. Approximately 50,000 tons of ore have been shipped to smelters from the property. Production has been made from two distinct and separate ore bodies of dissimilar types. The Shear Vein deposit has been mined to a depth of 500 feet below the surface without a reduction in the size of the ore shoot or the grade of ore. The Magnetite ore body has been partly mined to a depth of 200 feet below the surface. Because of the favorable production record of the Rush & Brown mine, the present need for copper and the fact that the owners were attempting to place the mine in production, it was deemed advisable to investigate this property under the Strategic Minerals Act of 1939 as a possible source of copper.

Jan 1, 1948