Search Documents

By Keith A. Heasley, Timotlly M. Barton

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence- Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents a case study where a mechanics-based, boundary-element program is used to calculate the surface subsidence associated with several panels of a Northern Appalachian longwall coal mine. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin seam or vein type deposits. In this paper. the program is used to calculate both the underground convergence and the resulting surface subsidence at three longwalls. The subsidence results from the model are compared with field measurements and analyzed The results from the case study in this paper demonstrate that the laminated model with calibrated properties can easily provide fairly accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies are recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

By Eric P. Bregman

As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800?s where busy commercial streets co-mingle with thickly settled residential houses. The subsurface conditions present within Boston?s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations. This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area.

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By Gabriel Esterhuizen, Tom Goodwin, Scott Schilling, Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

By R. P. Vinson, D. P. Tuchman

The personal dust monitor (PDM) is a sampling device developed for measuring the personal exposure to coal mine dust of mine workers. The device is based on proprietary technology known as the tapered element oscillating microbalance (TEOM) originally developed as a fixed- site environmental particulate mass monitor by Rupprecht and Patashnick Co., Inc., Albany, NY. Currently, the monitoring of exposure to coal mine dust relies on periodic samples taken by traditional coal mine dust sampling units that use a cyclone, filter, pump, and laboratory measurement of the filter mass. Better measurement of mine dust levels has been the goal of industry and labor for nearly two decades. PDM technology offers accurate, end-of-shift and near real time assessment of worker dust exposure. Laboratory and underground tests compared measurements taken by a prototype PDM-2 (a two-piece TEOM) to the average of multiple personal dust samplers monitoring the same space. In the range of mass loadings P between 0.5 and 4.0 mg/m the PDM met a 25% accuracy criterion 95% of the time with 95% confidence. However, some questions still exist about potential bias between types of coal. The prototype two-piece device is in the process of being combined into a single unit that also contains the miners' cap lamp creating a more ergonomic dust sampling system.

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By Tony Peach

Project Description The Ok Tedi Mine is located approximately 18 km east of the Papua and New Guinea-Indonesia border, on the southernmost extremity of the Star Mountains Range, it is situated almost equidistant from the north and south coastlines. The headwaters of the Fly River system are in the Star Mountains. The open pit mining activities are on Mt Fubilan with a (pre-mining) elevation of 2,095 metres (6,871 Feet) in the Western Province. The mine is in an area characterised by very steep topography and dense tropical rainforest. The pit has been free draining but will cease to be so in the first quarter of 2009. Ok Tedi Mining Limited (OTML) required a drainage tunnel to be driven under the mine, if possible before free drainage was no longer possible. The tunnel was required to be at least 5 m in diameter and 4,200 m (13,776 ft) long, with a possible extension of 1,100 m (3,608 Feet) if the mine decided it was required for additional drainage and underground exploration. The tunnel is being driven up grade at 0.67%, and will be connected to the pit by the raising boring of two 1.1 m (3 Ft. 6 In.) diameter shafts from the tunnel level 250 m (820 Feet) below to the pit. In Tabubil, the adjacent township at an elevation of 640 m (2,100 feet), air temperatures range from a mean at night of 20 (68°F) degrees centigrade to a daytime aver-age of 27 (81°F) degrees. Extremes of 12 and 39 (54°F?102°F) degrees centigrade have been recorded. Rain falls, on average, 339 days each year and totals 8,000 mm (315 inches), and have been known to approach 12,000 mm (472 inches) making the area one of the wettest places on earth. The portal site is at an elevation of 1,200 m or 4,000 ft and the air temperatures are a little cooler and the rainfall a little greater. Access to the mine is by air for personnel and light freight and by ship for heavier goods and materials. The port is at Kiunga on the Fly River 153 km from the portal site. The program for the project was tight, the decision to purchase the required TBM was made in July 2007 and the final decision to go ahead with the construction of the tunnel was made in November 2007.

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.

By Dean H. Ambrose

This paper presents a technique for representing and analyzing random motions and hazardous events in a computer simulated three-dimensional workplace, providing machine designers and safety analysts with a new technique to evaluate ways to reduce operator-machine interaction hazards. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. By simulating motions of an operator's random behavior and a machine's appendage, researchers can accurately identify hazards, and use that information to form safe designs for mining equipment appendage velocity. Validating the model provided improvements in the operator's optimal viewing area, work task- starting positions, and operator's motions for a more accurate random behavior. Preliminary simulation results provided (1) an interesting approach to research data gathering in that there was no need for live subjects and test sites and costs associated with experiments become insignificant and (2) that the model was versatile by showing it was capable of accurately mimicking the range collision forces versus speed, operators' size, and risk behaviors found in actual industrial situations and showed (I) that response time significantly affects the number of collisions experienced by the virtual subject and (2) that analysts must be discerning with the model and not read more From the databases than what the simulation model was designed to deliver. Keywords: random human-motion, anthropomebics model, machine-operator hazards, mine safety

By R. Raines, S. P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6-m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor variations in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

By Yong Pan, Purushotham Tukkaraja

Block caving is a preferred underground mining technique due to its high production rate and low operation cost. Before its final step into a mature caving system using gravity to break rock, drilling and blasting are required to form drawbells to connect the production level and undercut level and induce the initial caving propagation in undercut level. A large amount of toxic fume generated by blasting activities poses a big threat to people working in a confined environment and ventilation is assumed to be the most economical and efficient way to deal with this issue. Past research shows that it’s common to use traditional methods like using a formula or using numerical method (Computational Fluid Dynamic (CFD)) simulation to predict re-entry time after each blasting, but it fails to consider the percentage of toxic fume entrapped in muckpile, which could reach up to 70%. In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.