Search Documents

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By Don Dodds

Iron Mountain Mine Rehabilitation Project Brief History The Iron Mountain Mine is located in Northern California approximately 12 miles northwest of Redding. The ore body is a large, very dense pyritic intrusion, discovered in 1860, and initially minded for silver. The silver played out quickly and 34 years later the ore body was mined for copper. Copper mining was scheduled to cease in 1939, but WWII prolonged the closure. After WWII, the pyrite ore was mined to produce sulfuric acid. In 1949 when large amounts of cheaper sulfuric acid were being generated by the oil industry the underground mine shut down. Little was done with the site conditions until 1970 when the U.S. Bureau of Mines began monitoring the pH of the effluent. The initial pH readings were around 2.0. This was lower than anyone expected. Laboratory tests showed that when the ore from the mine was submerged in water, the pH of the water would stabilize above 4.0. However, the pH got steadily lower. In 1989 with the ph around 0.7, the U.S. Environmental Protection Agency (EPA) required the owner to build a capture and treatment facility. During this initial period, the majority of the effort was spent on the treatment plant. The relationship between the mine owner and the EPA was basically an adversarial relationship from the very beginning. In 2001, North Pacific Research was hired to upgrade the capture and control facility. The general layout of the Iron Mountain Mine is shown in Figure 1.

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By C. P. Besse, N. F. LeBlanc

Described in this paper are oceanographic data which should be considered by an offshore design engineer and methods for developing a design wave height from the oceanographic data. The selection of a design wave is predicated on contemplated waves which might affect the site throughout the life of the structure. Selection of a design wave height may be based on (1) arbitrarily established recurrence Frequencies of hurricanes affecting the structure (predicted wave heights are associated with the expected variations of forces resulting from these waves) and (2) a risk-type evaluation wherein all possible storms affecting the area are considered (anticipated wave heights are associated with both investment plus risk costs and expected variations of forces). It is shown how the following oceanographic predictions are integrated into design considerations: (1) a classification of storm intensity which considers all recorded storms which affected the design area, (2) the recurrence interval of storms of a given- intensity (this interval is dependent on the extent of the geographical area considered in the design problem) and (3) a forecast of all wave heights which might affect the area (geometry of a structure often necessitates consideration of waves from a multiplicity of directions). The authors believe that the described techniques can result in selecting an adequate and reasonable design wave. INTRODUCTION Since the inception of offshore operations in the Gulf of Mexico, engineers engaged in designing suuctural facilities have been plagued with the problem of selecting an adequate and reasonable design wave. In the development of any offshore structure it is mandatory that the engineer evaluate the ability of the structure to withstand the ocean waves to which it will be subjected. Selecting such design waves quite naturally necessitates a coalition of the oceanographer and the design engineer. The oceanographer must provide a detailed knowledge of scientific principles which govern the behavior of waters in the Gulf of Mexico. He should also have an adequate knowledge of the manner in which design waves are utilized by the engineer. Although the design engineer's primary responsibility is applying the oceanographer's specialized knowledge in the creation of real structures, it is important that he possess some knowledge of related oceanographic principles to reasonably evaluate and apply the recommendations of the oceanographer. In the Gulf of Mexico it is the hurricane wind waves which generally govern the design of an offshore facility. The oceanographer must therefore develop techniques for predicting the heights, periods and frequency of all hurricane waves which might affect a particular structure. From this mass of oceanographic data, the design engineer must select the design waves which will apply to his particular design. PAST STUDIES ON FREQUENCY AND AMPLITUDE OF HURRICANE WIND WAVES Past oceanographic studies on the frequency of hurricane wave heights in the Gulf of Mexico have been devoted largely to predicting the recurrence interval of hurricanes which will generate maximum significant waves of given heights. The maximum significant wave height is the average height of the highest one third of the waves in that portion of the storm producing maximum wave heights. Since these waves occur over a relatively small portion of the storm (Fig. 1) and since the paths of hurricanes vary considerably (Fig. 2), the recurrence frequency of such heights is largely a function of the extent of the geographical area considered. In establishing the frequency of maximum significant waves for the entire American Gulf coast, the major fully developed hurricanes which affected the coastline from BrOwnsville, Tex., to Key West, Fla., were considered (Fig. 2). These Storms were selected and described by C. L-

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method that can be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.

By Ron Ketterling

Donna Summer wrote and recorded a song in 1983 with Michael Omartian called, “She Works Hard for the Money.” The song was inspired by her encounter with an exhausted rest room attendant, Onetta Johnson, who is mentioned in the song by name, and featured on the album’s back cover. ISEE President James Daley, in the May/June 2019 in The Journal of Explosives Engineering discussed the Six Pillars related to the ISEE. We will use the Internal Processes pillar to frame this discussion. The Internal Process Pillar includes five separate sub-committees – we will see how this concept applies to both ATF Explosives record-keeping compliance and business process compliance in general. We will discuss electronic and paper record keeping, what works and what doesn’t. We’ll review record keeping in light of those five sub-committees: Audit, Awards, Constitution, Ethics and Planning. You’ll come away with concrete steps you can use to improve your record keeping processes. This paper will show you how to make the hard work of inventory management and ATF record keeping work hard for you.

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue. In spring of 2016, the Inauen Schatti company of Switzerland started the development of a flyable RACS deployment box to complement their 2 stand alone tower systems. To go along with the new flyable deployment box, a new S-Load charge carrier was developed. The newly developed and patented S-Load explosive charge for the LM32 RACS system features a mechanism which combines the explosive and priming material just before the blast. These are stored separately during transport and storage in the LM32 RACS deployment box. The S-load is divided into two parts. The upper part contains the plastic bobbin and ignition sequence (impact pull wire igniter, safety fuse and #8 blasting cap), whereby the explosive material and detonating cord are positioned in the lower part of the explosive container. The explosive material and ignition sequence are separated by a certified housing during transport and storage. The key idea of the S-Load system was to achieve a maximum level of safety by keeping the priming components separate from the explosive material until just before detonation. Because of this the S-Load and the LM32 tower remains safe during transport by helicopter or when being stored in the deployment box on the mountain side in the avalanche start zone.

By Brian White, Hamid Maleki

Sudden, violent failures of rock around mine openings influence access, ventilation, and safety in both hard-rock and coal mines. To develop predictive tools for assessing the potential for violent failure, the authors initiated a comprehensive study using (1) multiple linear regression and numerical modeling analyses of geological and mining conditions at 25 sites to identify the most significant factors contributing to stress bumps in coal mines and (2) investigations of the geological and mining factors contributing to rock bursts in the Coeur d'Alene Mining District of northern Idaho, particularly the influence of preexisting structures on rock bursts. Twenty-five factors were initially considered in the study of coal bumps. The most important variables were identified as (1) mechanical properties of strata, (2) gate road geometry and/or gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, and (4) stress gradients associated with previous mining and anomalous geologic conditions. In the Coeur d'Alene district, burst damage related to preexisting structures results primarily from (1) sudden buckling and crushing of rock layers where surfaces of development and production openings lie at low angles to bedding, faults, or other planar structures and (2) disturbance of loose ground caused by seismic fault-slip on preexisting faults or previously sheared bedding planes that intersect veins near pillar-stope margins.

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

By Todd M. Ruff

The lack of visibility near earthmoving equipment resulted in six fatalities in U.S. surface mining operations during 2003. These accidents were the result of either a piece of equipment striking another vehicle or worker, or the equipment traveling over the edge of an embankment. Figure 1 is an example of a recent accident that resulted in serious injuries to one worker and fatal injuries to two others when a van parked in front of a haul truck. Two fatalities occurred in separate incidents when front-end loaders struck workers. Another two workers were killed when their equipment backed over the edge of a highwall or dump point [1]. There is clearly a need to provide better information to equipment operators regarding their surroundings. [ ] Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are working to reduce these accidents by developing systems that sense obstacles and changes in terrain near the equipment and provide this information to the operator. Many off-the-shelf proximity warning systems that were developed for automobiles, light trucks, and recreational vehicles were evaluated on off-highway dump trucks [2]. Many limitations were found with existing systems, including frequent false alarms, limited detection range, a lack of specific information on an obstacle (e.g., location, identity), difficulties in finding suitable mounting locations, and an inability to withstand the environment. These limitations have necessitated the development of new systems designed specifically for large, off-highway, earthmoving equipment. New off-the-shelf systems available for mining equipment include radar and tag-based detection systems. Prototype systems now being developed include a proximity warning system based on the Global Positioning System (GPS) and a computer-assisted stereovision system. Development of these new systems was accomplished by working with manufacturers to modify existing systems to meet the needs of surface mining and through cooperative research with organizations to develop completely new solutions. A typical proximity warning system consists of a sensor or antenna mounted on the equipment that detects the presence of obstacles and an alarm interface in the cab of the equipment. Some systems, as described in more detail below, also require that other vehicles and personnel on the ground be outfitted with electronic tags that transmit an “I’m here” signal back to the system (e.g., radio signal detection systems or GPS). Many types of proximity warning systems are on the market, but they are not all discussed in this paper. APPROACH In past work, engineers at NIOSH evaluated several off-the-shelf proximity warning technologies in order to verify their effectiveness on off-highway dump trucks [2]. Dump trucks were chosen because of the number and severity of accidents involving this type of equipment and because extensive blind areas around these trucks are typical. This experience allowed engineers to limit the number of systems chosen for long-term tests at mine sites to those systems showing

By F. Ikumapayi

Hydrogen peroxide production was measured during the grinding of a complex sulfide ore, and its oxidizing effect on solid surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) with diffuse reflectance attachment measurement. In turn, an attempt was made to correlate the formation of hydrogen peroxide, surface oxidation and sphalerite flotation. Additionally, in order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the effects of major components of calcium and sulfate species present in recycled process water and the effect of temperature on sphalerite flotation were investigated through bench-scale flotation tests using complex sulfide ores. The significance of process water species in flotation was studied using tap water, process water and simulated water containing calcium and sulfate ions. Formation of hydrogen peroxide was revealed during the grinding of the complex sulfide ore, and its formation was counteracted by diethylenetriamine (DETA). The FTIR spectrum of the pulp solid fraction showed varying degrees of oxidized surface species, which are related to the concentration of H2O2 analyzed in pulp liquid. Bench-scale flotation using two different complex sulfide ores showed that sphalerite recovery is better in process water than in tap water. Flotation results also indicated a varied recovery of sphalerite at different temperatures in either tap water or process water.