Search Documents

By C. A. Brown

"Steady-state simulation has been used for over 20 years to optimise the operation of crushing and grinding circuits. Throughout that period continuing comminution research has been the basis for improving the models.Site surveys, ore characterisation, model development and investigation of different operating scenarios by simulation has proved to be a cost-effective method for improving plant performance. In this sense, this paper presents findings from experience with these valuable optimisation techniques with reference to specific case studies."

Sep 12, 2005

By D Symonds, S S. Kanchibotla, L Kennelly, G McNamara, J Gaunt, B Adiyansyah

Ban Houayxai is a gold-silver mine operated by Phu Bia Mining Limited in Laos since 2012. The first two years of operation processed predominately soft oxidised ore but subsequent years were expected to process more fresh hard ore. Fragmentation of the fresh primary ores was also expected to be much coarser than for the soft oxide ores. This coarser and harder ore is expected to significantly reduce mill throughput and mining productivity. The Ban Houayxai management realised the potential downside risk when processing fresh harder ores and implemented a blast optimisation project to deliver finer fresh ore to the mill without unduly increasing blast induced dilution and damage.JKTech and the Ban Houayxai drill and blast team began a joint blast optimisation project in April 2013 to achieve finer fragmentation from fresh ores. This was achieved by modifying the bench geometry, blast patterns and applying exceptionally high levels of quality control during implementation. Blast induced ore loss and dilution was controlled by adjusting the ore blocks for blast movement. Finer fragmentation from these modified designs improved mill throughput for the hard fresh ore by 46 per cent above design on average. These new practices have been embedded in site operating procedures and have provided a quick reference ‘cookbook’ document for the engineers.CITATION:Gaunt, J, Symonds, D, McNamara, G, Adiyansyah, B, Kennelly, L, Sellers, E J and Kanchibotla, S S, 2015. Optimisation of drill and blast for mill throughput improvement at Ban Houayxai Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

By F Kock, Y Sulianto, T Trott, B G. Putland, D Morgan

"Northparkes installed and commissioned a secondary crushing circuit in 2010 to debottleneck the semi-autogenous grinding (SAG) mill constrained grinding circuits. Following further improvements to the circuit (inclusion of a double deck vibrating screen), the project successfully delivered finer feed to the SAG mill. The result of this project was an increase in the milled tonnes from 5.6 Mt/a in 2012 to 6.0 Mt/a in 2013.The increased throughput rates introduced new challenges with the circuit becoming power limited. How to best optimise the available comminution power, while delivering the optimal particle size to the flotation circuit was made the key optimisation objective. To achieve this objective, Northparkes initiated a project that included engaging comminution experts. Recommendations included changes to the SAG mill including mill lifter design, increased grinding media charge levels and reduced grinding media size with aim of producing a finer grind size.Northparkes implemented these recommendations along with some other changes to SAG discharge grates and the mill discharge vibrating screen. This achieved a substantial reduction in the flotation feed particle size distribution (approximately 20 microns) by utilising increased average SAG power utilisation, in turn resulting in a two per cent increase in copper recovery.With power utilisation now maximised, the next phase of optimisation has moved to the throughput-grind-recovery relationship and the cost benefit analysis of installing additional grinding power.Citation:Sulianto, Y, Trott, T, Morgan, D, Bell, T, Kock, F and Putland, B, 2016. Optimisation of Installed Mill Power Post-installation of Secondary Crushing Circuit at Northparkes Mines, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 331–338 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Horacek, I K. Sheppard

Ok Tedi is in a period of transition. By 2008 mill feed will consist of higher levels of high-grade but metallurgically challenging skarn ores. Additionally, the Taranaki pit will start production in 2008 along with the start-up of a new pyrite concentrator. Taranaki ores are very high in sulfur. Sulfur is captured in a pyrite concentrate prior to tailing entering the Ok Tedi River. These and other complex scheduling issues will need to be resolved over a critical three-year period. With these requirements in mind, Ok Tedi contracted AMC Consultants to develop a custom version of the Life of Business Optimisation System (LOBOS¬) to assist medium-term production scheduling at Ok Tedi. LOBOS utilities enable Ok Tedi planning engineers to:import polygon-based reserve data (Blast Masters) from MineSightÆs Interactive Planning Tools (IP Tools); graphically construct block sequencing and material flow constraints; edit constraints defining standard scheduling, processing and financial relationships; define dump and stockpile attributes; and assign capacities to production systems, plants, dumps and stockpiles. LOBOS converts Ok TediÆs production scenario into a mixed integer program (MIP) and submits the resulting model to IlogÆs Cplex MIP Solver. The Solver seeks an optimal production schedule that maximises net revenue per mill hour while meeting all constraints. This paper introduces Ok Tedi and its production requirements and relates these requirements to the facilities developed for an Ok Tedi version of LOBOS.

Jan 1, 2007

By Rolley P

In the course of reviewing grade control practices at the Marvel Loch gold mine in Western Australia in 1992, FSSI Consultants developed and implemented a novel approach to ore selection using a method to maximise financial return (the MP method*). The approach was based on improved grade control sampling and an ore selection method which directly incorporates both a measure of the uncertainty in knowing the true grade of selection units in the definition of ore, as well as the operating cost and revenue parameters of the mining operation. During the past four years, FSSI Consultants have evaluated and refined the use of this approach and have implemented customised variations of the MP method at seven gold mines and a gold-copper mine in Australia. The previous methods of ore selection at most of these operations were based mainly on polygonal - sectional methods of grade estimation. At all of the sites where grade control optimisation has been given a fair trial over several months of production, the use of the MP method has been consistently rewarding to the mining operations. The benefits include increased run of mine ore stockpiles and low-grade stockpiles and decreased fluctuation in the production grade. Most operations have also benefited from a consistent ability to improve production grade through high-grading of the increased ore production. The increase in ore production has the logical benefit of reducing stripping ratios, increasing mine profitability and mine life.

Jan 1, 1997

By P. Davies

The Hillside Smelter presently under construction at Richards Bay, Republic of South Africa, will be, on completion, the fifth largest aluminium smelter in the world. The site selected for this plant is underlain by sandy soils of variable density to depths of 30m or greater. In order to firmly establish pile founding depths required for alternative pile types in the variable subsurface conditions prevailing across the site, a pre-construction test piling programme was conducted incorporating piles instrumented with resistance strain gauges. The results allowed analysis of the relative contributions of end-bearing and shaft friction to the overall bearing capacity of each pile type and permitted comparison with the predictions of conventional static bearing capacity analyses. Conformance with acceptance criteria in respect of allowable pile head movements for single piles was also examined.

Jan 1, 1996

By Z. Saw, C. Poveda, N. L. Mai

Optimising the throughput of a mining network comprising all equipment from shovels to semi-autogenous grinding (SAG) mills is a complicated task, yet the potential benefits can be significant. Key modelling challenges stem from the sheer number of possible routes which material can travel, different equipment operating under different constraints, and the rate of SAG mills being calculated through a nonlinear function of the blended materials’ rock attributes. Nevertheless, this is an ideal onapplication area of mathematical programming, a branch of operations research. This paper describes an application of mixed integer linear programming (MILP) to optimise the mining equipment network of one of the world’s largest copper mines.The model takes as input a year-long monthly mine schedule of shovels in different pits, pushbacks, sequences and faces which produce material to be moved through a network of crushers, conveyors, silos, distributors, stockpiles and SAG mills, ultimately outputting a daily operational plan for all equipment that maximises the throughput of the network. All operational constraints and business rules are considered, including three quality attributes of copper ore. Comparing model results with actual data shows an improvement of 4.47% in network throughput tonnage. Additionally, although the model is solved using a free, open-source solver, optimal solutions are still achieved within a practical timeframe.

Sep 1, 2021

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Optimisation of the Advanced Automation System at Inmet Mining's PyhSsalmi Mine, Finland

Sep 13, 2010

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By S. J. Macnaughton

The Olympic Dam deposit in South Australia contains 2% copper and 0.06% uranium, which are present as bomite, chalcocite, chalcopyrite, uraninite, coffinite and brannerite. The copper is principally recovered using flotation. The flotation tailings, which contain the bulk of the uranium, and typically 0.3% copper, are leached using sulfuric acid and an oxidant at atmospheric pressure. This paper describes the results from a detailed investigation of the leaching behaviour of this ore. The influence of acid strength, Fe3+ concentration, redox potential and temperature on the dissolution of uranium and copper minerals was studied. Experimental data were obtained from extensive batch leach tests. Mineralogical studies, including SEM analysis of individual mineral grains, were also carried out. The maximum extraction of uranium determined experimentally was in good agreement with that predicted from SEM determination of the proportion of refractory brannerite in the ore. The leaching rate of copper was found to be independent of acidity over the range 20 g L-' to pH 2.0, but was strongly dependent on temperature and Fe3+ concentration. Uranium extraction showed a weak de endence on acidity, Arrhenius temperature dependence and a complex co-dependence on F>+ concentration and redox potential. A kinetic model has been developed, which predicts copper and uranium dissolution. This model will be incorporated into a more comprehensive model that can be used to predict leach performance and reagent consumption for specific ore samples.

Jan 1, 1999

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By A Jakowetz

OxianaÆs Sepon Copper Operation (part of the combined Sepon Gold and Copper Operation) is located in Savannaket Province, in southern central Lao PDR. The site is relatively remote, being some five hours inland from the Laos/Thailand border crossing on the Mekong River. The copper processing plant was designed to treat 1.3 Mtpa ROM ore to produce 60 000 tpa of copper cathode. Commissioning of the processing plant was completed in mid March 2005 with ramp up completed in January 2006 with 5260 tonnes of cathode harvested in this month. The focus of this paper is on SeponÆs unique grinding circuit. The entire grinding circuit is operated at highly acidic conditions, adding a number of different operational issues over and above those normally associated with grinding circuits. It became evident early in the ramp up, that reaching design mill throughput of 170 dry tonnes per hour with the original design would be challenging, coupled with the realisation that ceramic grinding media consumption had been underestimated. In order to lift the overall throughput of the processing plant, a significant continuous improvement process has been implemented within the grinding circuit to lift this key unitÆs production capacity. This presentation will focus on the key areas that have been addressed in the 12 month ramp up period and highlight areas for future work. Results to date have shown this improvement process to be very successful, with throughput rates in excess of 200 tph regularly achieved.

Jan 1, 2006

By B Davis, A H. Benzer, A N. Mainza, C M. Evertsson, L M. Tavares, M M. Hilden, M S. Powell, C Rule, G Asbj÷rnsson

The Mogalakwena North Concentrator of Anglo Platinum Operations was built with the capability to allow for future projected expansion. Several research groups, currently working with Anglo American on collaborative research over a range of projects, were brought in to review the existing operation, with a view to releasing some specific bottlenecks and providing specialist design input to the potential plant expansion.Based on a thorough review of the high pressure grinding rolls (HPGR) and crushing circuit, a wide range of de-bottlenecking opportunities were identified. This was followed by a series of surveys to provide performance measurements and to model the circuit in detail. From this effort a full simulation of the plant has been developed, including updated models of the HPGR, crusher, bins and screens. These models have been implemented in the researchersÆ Model Development Kit (MDK) version of JKSimMet, and in a prototype dynamic simulator based on the Matlab Simulink software.The observations, measurements and simulations have provided guidance and quantified the benefits of some proposed circuit modifications. Based on these findings a number of upgrades are being planned, with the aim of ensuring full utilisation of the installed equipment. The circuit demonstrates a potential expansion of over 30 per cent through minor improvements, and a 70 per cent increase in capacity with the addition of some strategic equipment.The HPGR-crushing upgrade project demonstrates the potential benefits of nurturing disparate Research groups into a strong inter-disciplinary technical team capable of supporting operational needs while developing future technology.CITATION:Powell, M S, Hilden, M M, Evertsson, C M, Asbj÷rnsson, G, Benzer, A H, Mainza, A N, Tavares, L M Davis, B, Plint, N and Rule, C, 2012. Optimisation opportunities for high pressure grinding rolls circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 81-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By L Köresaar, J Moilanen

With lower and increasingly variable Fe grades in iron ore resources, the monitoring of Si, Al, Mg and other light elements to meet quality requirements is gaining importance in the iron ore beneficiation industry. The high cost per manual assay and associated manpower requirements often limit the frequency of shift composite samples and laboratory assays. Furthermore, the shift composite assays represent past performance of a plant but are not useful for immediate reactions to feed variations, detection of equipment malfunctions or process control. Automated online analysis of light elements radically reduces the cost per assay and provides repeatable, timely data for process analysis, control and optimisation.A light element online slurry analyser, based on laser-induced breakdown spectroscopy (LIBS) optical emission technique, will be presented. This paper discusses the analyser design for the iron ore industry and also reviews the performance of the analyser against the manual laboratory. Additionally operator safety, user friendliness and maintenance requirements are discussed.A case study will also be discussed in this paper. The sophisticated measurement technique has been implemented in an industrial automated analyser and sampling system to allow for slurry measurement for up to 12 sampling points. However, careful selection of the sampling points and implementation of the sampling system is required for smooth operation.CITATION:Köresaar, L, Timperi, J and Moilanen, J, 2015. Optimised process control in iron ore via online analysis of light elements, in Proceedings Iron Ore 2015, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Maulen, K van Olden, T Elkington

A large open pit is planned at the site of an existing underground mine. Strategic planning work has been undertaken to investigate the project value associated with an expansion of underground operations in conjunction with the proposed pit. Previous analysis determined that any depletion of the available pit resource that changes the optimum pushback sequence has a significant negative impact on overall project value. Therefore, to investigate the viability of an underground expansion requires a system to identify the stope resource that would add value to a combined operation if mined ahead of the pit. The key solution to this problem was to generate a resource model variable that defines the blocks, which have greater discounted value if mined by stoping rather than by the open pit. A key assumption was that the open pit is the main driver of overall project value. From the identified potential underground resource, series of mineable stope shells were generated at a range of cut-offs. This stope reserve data formed the input to a mixed integer program based software tool that was developed and used to optimise the underground mining plan, at conceptual level, for various project configurations. A dynamic programming tool was then applied to evaluate the optimum value of a combined open pit and underground operation. The overall objective of this project was to determine the strategic plan that yields the optimum value for a combined undergroundûopen pit operation. The results provided a clear focus and direction for more detailed design and planning.

Jan 1, 2009