Search Documents

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. The history of the drilling of Pilot Hole "XI' is presented. This historical summary provides the details of method used during the drilling of this hole. Problems encountered during drilling are discussed. The quantities of drilling mud and other materials used to drill the hole are documented.

Jan 1, 1977

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By K. B. Rojiani

Surface mining activities disturb large tracts of land resulting in the potential for greatly increased downstream sediment loads. The Surface Mining Control and Reclamation Act of 1977 places increased emphasis on the protection of the environment from the adverse effects of surface mining operations. Surface mining activities must be planned to minimize disturbance to the hydrologic balance, erosion and sediment contributions to receiving streams. Sediment ponds must provide a sediment storage volume equal to the accumulated sediment volume from the drainage area as determined by the Universal Soil Loss Equation (USLE) or other empirical methods established by the regulatory authority. It has thus become extremely important for the mining industry to secure more accurate estimates of potential erosion losses and sediment yield. Accurate estimates of sediment yield are required for the planning, design and successful operation of sediment control systems such as detention ponds and other alternative control structures and for evaluating the effectiveness of land management practices. The principal soil loss prediction procedure available for use is the LISLE. The USLE procedure is inadequate for use in predicting soil loss from surface mine regions for a number of reasons. These include: 1. The USLE was developed to estimate average average annual loss from agricultural soils. It cannot predict accurately soil loss for specific storm events. In surface mine regions a major portion of the soil loss occurs during the initial six months to one year of active mining. Accurate estimates of soil loss over short periods are thus required for the design of control structures. 2. The slope length and gradient factors used in the USLE were obtained from data or cropland having slopes ranging

Jan 1, 1983

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By M. D. Marshall

A survey showed that there were 24 bin-related fatalities in the 5 year period of 1975 to 1979 in the minerals industry. Only 4 victims wore safety belts and only 1 of these had a second person attending his lifeline, as mandated by Federal safety regulations. Not one victim observed the three main Federal safety regulations governing work in and around bins. A study was conducted on the force necessary to pull victims partially buried in sand and limestone. Recommendations are made on procedures and safety equipment that can minimize bin-related accidents. A Handbook, directed to the plant engineer responsible for bin design and safety, was also issued detailing bin designs and flow-aid accessories as a function of the flowability of the stored material to better maintain material flow from bins. A comprehensive table of the flowability of many materials produced in the minerals industry is presented and simple procedures given for determining the flowability of materials if not available.

Jan 1, 1984

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By Amitava Ghosh

A new analytical formula for predicting ground vibrations induced by blasting is proposed. One factor accounts for geometrical spreading. One factor corresponds to inelastic attenuation. The geometrical spreading function is based on likely source geometries, idealized as either square-root, cube-root or site-specific scaling, and on the propagation characteristics of predominant wave types. The inelastic attenuation is approximated by an exponential function. The empirical constants in these functions are backcalculated from field measurements. Regression analysis has been performed on twenty-three sets of measured data in order to determine the validity and the effectiveness of the proposed method. In many cases, the proposed method gives better correlation than the conventional method. In most of the remaining cases, there was no difference between the two methods. Best-fit lines given by the proposed method fit the data trend very well, especially at large scaled distances. At large distances the proposed method gives a prediction much closer to the actual values than the conventional methods. The statistical analysis shows not much difference between square-root, cube-root or site-specific scalings.

Jan 1, 1983

By Clayton R. Morlock

Airblasts have been monitored at four coal strip mines and at a limestone quarry. Thirty-seven production blasts have been monitored with three seismographs, resulting in one hundred and eleven complete air pressure records. Instrumentation selection use is described. Data analysis includes an assessment of the predictability of peak overpressures by means of the cube root scaled distance law. It is found that predictability for the cases studied here is not good. An extensive discussion of possible explanations is included. A detailed analysis of the frequency content of the observed airblasts, of considerable importance in evaluating potential annoyance problems, has been made for all records. A computer program has been written to simulate airblasts induced by multiple-hole blasts. A series of small experimental blasts have been detonated and monitored in order to allow an assessment of the program. It is clear that airblasts, especially when induced by very small charges and monitored at very close distances, are highly sensitive to detonation times. Retrofitting of airblast records occasionally was possible, but considerably improved field work is required to validate or refute the computer model.

Jan 1, 1983

By John A. Kost

Control of the dust produced by continuous mining machines in coal mines is conventionally attained by water sprays from fixed nozzles mounted on the frame of the machine behind the cutting head. In the tests conducted under this contract a so-called "wet-head" machine was used, where the spray nozzles were mounted on the rotating head itself, close to the coal-cutting bits. The tests were conducted at the Robena Mine of U.S. Steel Corporation, using Lee-Norse machines. Operating the wet-head machine and a conventional spray machine in turns in the same section, it was found that the wet-head produced approximately 25 percent less respirable dust and 60 percent less total airborne dust than the conventional spray machine. The wet-head also greatly improved the visibility of the cutting bits from the machine operator&apos;s position. Several difficulties had to be overcome before any meaningful tests could be conducted, including excessive pressure drops in the piping system and plugging of the nozzles from internal water contamination. The major obstacle, however, was the rotating water seals on the wet-head, which leaked excessively after only a few hours of operation. Only after several changes and plant and laboratory tests was a design found which permitted conducting the underground tests without appreciable water leakage.

Jan 1, 1976

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 percent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Data summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By Mackenzie Burnett

Quick-Fix Blowout Stoppings were evaluated in several underground mines as an alternative to conventional ventilation control bulkheads. Blowout stoppings offer considerable savings in bulkhead construction and repair costs if the 0.1 inch H20 of differential pressure required to inflate them is available. The Quick-Fix Blowout Stoppings were utilized successfully in uranium mines in the Southwestern United States where savings in bulkhead construction and repairs to blast damaged bulkheads are estimated to equal $9,500 over the projected 2 year average life of a blowout stopping. Two types of material were evaluated. Five methods of anchoring the stoppings to drift walls were evaluated. Three methods of anchor attachment to the stopping material were evaluated. Blast pressure measurements were made in conjunction with the evaluation of the blowout stoppings.

Jan 1, 1978

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Louis Schaffer

A literature review concerning dredging hazards and dredge safety practices and an examination of MSHA accident and injury statistics on dredge mining in the United States provided the background for an analysis which was completed by visiting 31 dredge operations, dredge manufacturers, and dredging experts. The principal hazards are discussed and countermeasures are suggested in several areas. Drowning is the single largest fatal injury category. Special emphasis is given to the design, care and use requirements of personal flotation devices.

Jan 1, 1984