Search Documents

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

"Mine ventilation is in every underground mine a crucial process to ensure mine safety as well as acceptable working conditions. On the other hand is also a major cost factor depending on air requirement and air resistance. Due to the fact that the special layout of mines develop over time, ventilation systems change as well. This may result in complex systems which are suffering severe problems and low efficiency. With attention to the mine safety and costs, ventilation systems have to be controlled repeatedly and optimized continuously to fit changing conditions. The project “Improvement of ventilation systems in narrow vein mines” has been commenced with measuring and data collection in the Bogala Mine, Sri Lanka. This over 150 year’s old graphite mine consists of about 20 levels. The resulting ventilation system is highly complex and suffers problems like high temperatures and humidity as well as a mixing of fresh and used air on lower levels. To solve these problems and to optimize the system the complete ventilation system had been measured on-site first. The gained data have been used for simulations to develop and select an optimal and cost efficient solution. OBJECTIVE As an important process in mining ventilation is a major cost factor and can determine the economic feasibility of a mine. Due to the production mine layouts develop over time and mines increase in size and depth while the ventilation system becomes more complex and may suffer severe problems and inefficiency. Therefore mine ventilation systems have to be controlled and optimized regarding the general requirement of mine safety and health of the miners as well as the costs. Depending on the deposit type, depth, mining method, climate and as well corresponding laws and regulations the possible solutions are varying strongly. The work carried out paid special attention to the improvement of ventilation in narrow vein mines in tropical climate, in this case the graphite mine “Bogala” in Sri Lanka, South Asia."

Jan 1, 2015

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Xinyang Wang

It is believed that sulfur and volatile matter contents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal - three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By M Bird, B Oats, M Sganzerla

Mining operations are continually aiming to reduce operating costs to improve plant profitability. One way in which the Cannington operation sought to achieve this was by increasing the wear life and reducing the energy consumption of their flotation mechanisms. This was made possible using Outotec’s FloatForce mechanism. The FloatForce mechanism has been developed by Outotec over a six year period involving both CFD modelling and rigorous site testing. FloatForce delivers improved air dispersion and cell agitation efficiency; as such it can be operated at lower rotor tip speeds when compared to Outotec’s previous mechanism.Cannington trialled three FloatForce mechanisms in a train of ten OK38 zinc roughers. The mechanisms’ rotational speed was reduced by 10% compared to the previously installed MultiMix mechanisms. The purpose of the trial was to quantify the energy saving and assess whether there was any reduction in plant metallurgical performance.The trial was successful with FloatForce delivering a 17% reduction in power, an improvement in wear and improved recovery. Analysis of pre and post-installation metallurgical accounting data showed the following:The FloatForce installation resulted in a recovery increase of zinc to zinc final concentrate of 0.4 – 4.0%*The FloatForce installation resulted in a recovery increase of lead to zinc final concentrate of 0.0 – 0.3%*There was no statistically significant change in silver recovery to zinc final concentrate that can be attributed to FloatForce**95% confidence interval (CI) using multiple linear regression models.The Cannington operation is now in the process of further optimizing its power consumption and wear savings by changing the remaining OK38 zinc and lead rougher float cells to FloatForce mechanisms.CITATION:Bird, M, Oats, B and Sganzerla, M, 2015. Improvements in flotation cell maintenance, power consumption and operation at South32 Cannington, in Proceedings MetPlant 2015, pp 230–245 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012

By George Mandarakas, Johan van Zyl, Karl-Heinz Becker

The world’s climate today has changed compared to 10 or 20 years ago. Many countries face water shortages; water sourcing for mining activities has become harder to secure. ESG’s focus on the industry has made us more aware of the need to preserve and responsibly use the water needed for wet processing in our milling and sorting activities. In a recent greenfield project in South Australia, 10 Gigalitres per annum would be required to process 5Mtpa of magnetite [1]. Published information indicates that the mining industry consumes approximately 12 EJ per year—or 3.5% of total global final energy consumption globally [2] or 3.33 trillion kilowatt hrs. This energy consumption is significant, considering the critical role mining plays in extracting and processing essential minerals for economic development and human progress. The perception of the mining industry is that not only does it consume significant power, but it also consumes a lot of the freshwater in the world. In fact, it consumes approximately 5% [3] of the total freshwater demand. According to the Intergovernmental Panel on Climate Change (IPCC), by 2050, 60% of the world’s population will be living in countries that are classed as water-stressed [3]. As more and more emphasis is placed on renewable energy sources, the amount of water used in mineral processing will increase because more and more raw materials require a water-intensive process. This increases the pressure on the mining industry to try and find water-saving initiatives. As part of this review, recent advancements in magnets have enabled magnetite processing facilities to achieve between 30 to 40% dry gangue material rejection before the wet beneficiation process (grinding and sorting). This reduction in energy consumption allows the reduction of energy consumption. Secondly, there is less material ground in the mills, which requires less water for mineral downstream processing.

Feb 1, 2025

By J. F. T. Agapito

Significant increases in extraction ratio on the order of six to eight percent, equivalent to as much as 142 t/m of panel advance, have occurred at the Big Island Mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-laying trona beds at depths of 250 to 260 m in the Green River Formation in south-western Wyoming.

Jan 1, 1988

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012