Search Documents

By K. F. Unrug

The identification of the major subsidence areas in the Western Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential. It is recommended that further site specific studies should be performed on this area.

Jan 1, 1986

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By D. A. Bird

Water chemistry data were used to identify the sources of ground-water and surface-water inflow to the IOZ block cave mine. Water samples were collected to obtain vertical and lateral hydrochemical profiles within different levels of the underground workings. Water chemistry data were evaluated in conjunction with geologic and structural information to define controls on locations of ground-water inflows, and to select targets for drilling and interception of water. Drilling has intercepted water-producing zones that were previously unidentified through mapping and drilling. The program has resulted in a reduction in water inflows to the block cave area.

Jan 1, 1998

By R. J. Durrheim, Y. Yabe, M. S. D. Manzi, DSeis team, N. Z. Nkosi, S. B. Mngadi, Jr. H. Ogasawara

On 5 August 2014, the Orkney M5.5 earthquake, the largest in South African gold mining districts, occurred with an unusual strike-slip mechanism at great depth of 4.78 km below the surface. In a rare case, the ML 5.5 earthquake occurred within the area covered by the legacy 2D and 3D reflection seismic data acquired in the 1990s and 2000s for gold exploration and mine development. In addition, the earthquake ML 5.5 rupture plane was recorded and accurately delineated by the underground in-mine seismic network near the source region. The integration of the legacy 2D reflection seismic data and mine seismicity data allowed us to identify a near-vertical structure, striking northnorthwest-south southeast (NNW-SSE). The ICDP-DSeis team drilled three holes (Hole A, Hole B, and Hole C), and two holes (Hole B and Hole C), intersected the upper edges of the ML 5.5 rupture. These holes recovered metasediments, metabasalts, intrusive rocks including dolerite sills and lamprophyre dykes adjacent to the fault zone, and the fault gouge. Late Prof. Tullis Onstott and geomicrobiologists installed a packer in Hole A and successfully recovered saline water and detected gas (~10 MPa). Slip weakening and rupture propagation are significantly influenced by the existence of fault gouges and the production of wear material between two sliding rock surfaces. Using the fault gouge material recovered from Hole C, we conducted friction experiments under dry and room temperature conditions at high slip velocity of ~100 mm/s and normal stress of 2 MPa. The resulting steady-state frictional strength was ~0.66 over a slip weakening distance of ~9.1 m. The steady-state frictional strength was high, which may be caused by large gouge thickness, and the rate of wear generation. As a result, it is proposed that the Moab Khotsong ML 5.5 seismogenic zone is complex and could be controlled by three main processes: a) the complex structural architecture of the seismogenic zone (e.g., intersection of fault, lamprophyre dykes, and dolerite sills); b) the mechanical process induced by tectonic and/or mining related stresses; and c) the mechanical and chemical processes caused by the water and rock interaction.

Jan 12, 2025

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By Dan W. Bench

PCBs are hazardous not only to human health and the environment but also to the mining industry because of potential worker exposure and improper disposal liabilities. In this sense, the paper point out the identification, management, and proper disposal of pcb-containing electrical equipment used in mines. Also it point out alternatives to PCB dielectrics, storage, and disposal. The use of PCBs in mines has been documented during U.S. Environmental Protection Agency Region 8 mine inspections and it used as dielectrics in transformers, capacitors, and fluorescent light ballasts are common throughout industry worldwide.

Sep 14, 2009

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By G Danckert

The key technical theme of ‘orebody knowledge’ has been applied by Rio Tinto in the Pilbara iron ore precinct from 1966, when operations first started there. It forms the basis of present day application, as well as planning for the future.This paper will review how the early towns and mines commenced and how they formed the basis of Rio Tinto’s early operations, on which the Pilbara precinct has been based. A profile of the last decade of Pilbara growth will be highlighted, together with the current integrated network of mines, rail and ports and the next generation of expansions.The paper will specifically describe the Rio Tinto process of significant resource evaluation, including comprehensive drilling programs and the conversion from resource to reserves. It will also describe the overall mine planning process, both from the strategic view, as well as for short-term mine plans.The ability to innovate in resource development will be discussed. This will include not only the technical dimension of changing cut off grades, use of low-grade ores and managing low-grade stockpiling and beneficiation, but also the broader application of new technology and innovation in the iron ore business.

Jul 11, 2011

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By Peter Zhang, Daniel Su, Mark Alexander Van Dyke, Heather Dougherty, Bo Hyun Kim

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a post-mining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64°, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457-m wide and 3657-m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones in longwall gobs.

Jun 9, 2022

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

The global mining industry has recorded significant declines in accident and injury rates attributed to the advancement in technology, increased enforcement, and safety consciousness. A goal of the mining industry is to achieve zero injury and occupational illness on all mine sites, prompting increased research into ways to further reduce mine accidents. A machine learning technique known as multiclass logistic regression is applied on a 10-year injury dataset from the Mine Safety and Health Administration (MSHA) to determine a miner’s susceptibility to a class of injury and to help identify significant risk factors associated with different classes of injury. The data is aggregated based on injury classification to provide statistically relevant results. The analysis identifies specific risk factors that influence a mine worker’s susceptibility to a given class of injury, i.e., non-fatal with no days lost or restricted activity, non-fatal with days lost and/or days of restricted work activity, and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal vs. non-coal), experience on the current job (years), shift start time, employment type (operator vs. contractor), mining district, and type of accident. The results of the analysis indicate that a miner’s experience on the job, i.e., the number of years worked in a current job, is a significant risk to injury occurrence, even for those with decades of total mining experience. We further show the differences and similarities between the surface and underground mine incidents.

Nov 3, 2020

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

This study applies a machine-learning technique known as multiclass logistic regression on a 10-year injury dataset from the U.S. Mine Safety and Health Administration (MSHA) to determine miners’ susceptibility to injury and to help identify significant risk factors associated with different classes of injury. The analysis identifies specific risk factors that influence a mineworker’s susceptibility to a given class of injury: nonfatal with no days lost or restricted activity; nonfatal with days lost and/or days of restricted work activity; and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal versus noncoal), experience on the current job (years), shift start time, employment type (operator versus contractor), mining district and type of accident. The results of the analysis indicate that a miner’s experience on the job (the number of years worked in a current job) is a significant risk to injury occurrence, even for those with decades of total mining experience.

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By T. C. Maswanganyi, G. L. Smith, R. C. A. Minnitt

This paper identifies the strategic gaps and opportunities for the South African mining industry’s contribution towards advancing sustainable development. Mineral resources companies are confronted by a range of complex social performance challenges, which largely manifest in sporadic community and labour unrest, undermining the sustainability and profitability of these companies. Integrating supply chain management, strategic long-term planning and sustainability planning is identified as a strategic gap that can contribute towards the sustainability of mining companies, if effectively implemented. Contributing towards sustainable development by the South African mining industry is not merely a voluntary requirement on the industry but a legal requirement in terms of the Minerals and Petroleum Resources Development Act No. 28 of 2002. This Act is legislation aimed at advancing socioeconomic development in communities that host mining operations and in areas that provide labour to the South African mining industry. In contributing towards the advancement of sustainable development in mining host communities, not only will mining companies fulfil a legal requirement in terms of the Minerals and Petroleum Resources Development Act, but they will also prevent negative social and economic impacts in those communities. This paper identifies innovative and cost-effective ways of advancing sustainable development by integrating strategic supply chain management, strategic long-term planning, and sustainability planning.

Dec 15, 2025

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today&apos;s rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world&apos;s large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry&apos;s current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By J. L. Bellanca, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not constitute endorsement by NIOSH. ABSTRACT Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which presents an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders' evaluations. The study includes considerations for safe technology integration. INTRODUCTION Striking, pinning, and crushing accidents related to mobile machines continue to be a major concern in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) linked 22 of the 75 underground mine fatalities reported between 2011 and 2015 to power haulage [1]. The Mine Safety and Health Administration (MSHA) asserts that proximity detection systems for mobile machines (mobile PDSs) could help to prevent these types of fatal injuries [2]. Mobile PDSs use a collision avoidance technology that allows the mine to establish hazard zones and employ electromagnetic sensors to detect workers equipped with a miner-wearable component (MWC) working near these mining machines. The authors characterize a mobile PDS as an automated technology, because—in line with Lee & See’s [3] definition of automation—a mobile PDS actively “selects data, transforms information, makes decisions, or controls processes” (p. 50). When the system detects workers in the established hazard zones, it issues alerts and slows or stops the mobile machine. Even though a mobile PDS may be a viable and promising safety solution, there are still a number of questions regarding how well this automated technology will fit with mining tasks and conditions. Using a mixed-methods approach, the current study explored factors that influence the fit of mobile PDSs in the underground mining environment.

Jan 1, 2019