Search Documents

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

By R. J. Sweigard

One of the foremost problems in reclaiming prime farmland is compaction of the subsoil which is caused by the reclamation equipment. Wheel tractor-scrapers are most commonly used to replace subsoil and have been blamed for the majority of the compaction problems. Two methods of alleviating this problem that are presently being considered are mechanical subsoil loosening machines and truck- shovel combinations for subsoil handling. A field study was conducted in which dry bulk density measurements were taken in an effort to determine the effectiveness of truck-shovel combinations and subsoil loosening equipment in reducing bulk density in comparison to typical scraper replacement.

Jan 1, 1987

By D. E. Roberts

Over 425 million used automotive oil filters are discarded in the United States each year. Estimates prior to this research claim that 10% are recycled with the remainder typically being landfillcd. Surveys conducted with ferrous scrap users and oil filter processors as part of this research reveal that at least 15% are currently being recycled as ferrous scrap. Oil filter scrap is not being used by many operations because of concerns with scrap consistency and quality. These concerns stem from trials conducted in the infancy of the oil filter recycling movement. Consistent scrap quality depends both on the content of the used oil filters and the processing technique used to produce the scrap. Technology has advanced since the first recycling trials were conducted by steelmakers. Several different types of scrap are available, including pucks, bricks, cubes, and shred. This research conducted at the University of Missouri-Rolla investigated the content of used oil filters and compares the recyclability of different oil filter sizes and designs. Filters vary by application and vary between manufacturers for a particular application. An understanding of the scrap itself as well as the concerns and problems of both oil filter recyclers and oil filter processors is necessary to increase the number of used oil filters being recycled.

Jan 1, 1996

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By D Laurence, L Ge

This paper demonstrates use of remotely sensed imagery in promoting sustainable mining. Remote sensing technology can be used during all phases of a mining project û from evaluating the resource, to making extraction more cost-effective, through to monitoring, mine closure and remediation. Use of the new generation of satellite platforms with the capability of acquiring satellite data with higher spectral and spatial resolution have the capability to emerge as essential indicator for sustainable development in the minerals industry. A life cycle approach to satellite imagery is discussed. The use of an imagery of the site prior to mining activity establishes the environmental baseline, guides mitigation measures and eventual help in suggesting remediation. Remote imagery provides the cost-effective means of monitoring reclamation, including the growth of planted vegetation, of the mine site and surrounding area. The latest advancements in satellite remote sensing are highlighted to meet the newer challenges of sustainable mining practices. Some of the worldwide successful remote sensing applications for the measurement and evaluation of the sustainable development impact of mining operations are described. Presently available source of imagery and its comparative advantages and disadvantages are provided as a guide. Finally, the limitations of this tool are indicated.

Jan 1, 2009

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

By S. Paul Singh

"The long-term viability of seismically active and/or deep mining operations hinges upon the industry's ability to maintain profitability in a climate of increasingly difficult conditions, escalating operating costs and fluctuating metal prices. Within this context, it is prudent to explore mining techniques that could provide means for safer and more profitable extraction of seismically active and/or deep seated deposits that are vital to the long term survival of the industry.The first step was to examine Penetrating Cone Fracture (PCF) and other relevant concepts with the objective of semi-continuous mining in deep underground hard rock mines. This was followed by an assessment of the current conventional drilling and blasting practice. Thirteen blasts were monitored in five different seismically active workings of an operating deep mine. The main concerns during the current drill and blast practice were identified.On the basis of the literature review, three short round blasting techniques were short listed for further review. These techniques were evaluated based upon the available literature and discussions with the persons associated with their applications. Justification, requirements and major challenges for the application of short round blasting have been discussed in this paper. Suggestions for improving the current drilling and blasting practice have also been outlined.INTRODUCTIONRock fragmentation is the key to mineral excavation and production. Increasing working depths, environmental concerns and trends towards continuous mining necessitate the development of new and improved rock breakage methods.The excavation of hard rocks is still dominated by the sequential routine of face preparation, drilling, charging explosives, blasting, ventilating for fume and dust removal, mucking and roof support. Worse still, drilling and mucking require specialized equipment that fills the end of the heading so that no other operation can be performed and the equipment must be removed from the face to protect it from fly rock."

Jan 1, 2010

By Robert M. Dreyer

Thirty years ago it was possible to locate a quarry site for crushed rock for concrete aggregate by finding the nearest solid rock bluff accessible by road, But times have changed and the location of a quarry site to furnish crushed rock for concrete aggregate now has become rather complicated, Although both sand and gravel can be used for aggregate, this discussion will be confined to crushed rock in the regions around a metropolitan area. Let us assume that a consultant has been retained to advise on the desirability, and the possibility, of opening a new quarry within a given area. The problems are geological and ecological. Since the geological problems are simpler, they will be discussed first. Generally, the first step is to make a market study of competitive aggregate sources within the projected area. Assuming that the quality of aggregate to be sold by competitors as well as their mining costs will, within narrow limits, be the same, the problem becomes essentially a study of haulage costs from established quarries into the projected new area. Since haulage cannot be effected along straight lines and since each quarry operator may have different unit haulage costs, a map showing lines of increasing cost intersecting points on roads available for truck haulage radiating from competitive quarries can be rather complicated. Such a map, more-over, changes each time a new haulage contract is negotiated by a

Jan 1, 1971

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By S. A. Villalobos, F. A. Villalobos, and L. E. Aguilera

Rockburst events have been a serious problem for many years in many mines worldwide, and in particular at El Teniente mine in Chile. El Teniente is the largest copper mine in the world, located in the Andes Cordillera where high stress levels are present due to intensing mining activity in addition to complex geology. Consequently, the study and management of the rockburst threat are necessary. In this work, the case of the Diablo Regimiento (DR) mine within El Teniente is studied. The energy capacity of dynamic support systems is determined for different tunnel geometries based on two kinetic methodologies, using data from DR. Initially, rockburst potential is determined by means of a stress analysis around different tunnel geometries through the boundary elements method. In the first methodology a yielding zone (YZ) is estimated for each excavation geometry using the finite element method FEM. The second methodology involves the definition and determination of a critical strain energy (SE) around each excavation geometry using a FEM numerical analysis. In both cases, peak particle velocity PPV is estimated by a scaling law, which is subsequently adjusted due to tunnel amplification effects. According to the results, and knowing the working energy capacity applied in DR mine, it was found that the values of energy capacity for the rock dynamic supports were better estimated by the YZ-PPV approach than by the SE approach.

Sep 1, 2022

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

"The main purpose of geometallurgy is to develop a model to predict the variability in the mineral processing performance within the ore body. Geometallurgical tests used for developing such a model need to be fast, practical and inexpensive and include as an input data relevant and measureable geological parameters like elemental grades, mineral grades and grain size. Important in each geometallurgical program is to define the number of samples needed to be sent for geometallurgical testing to enable reliable metallurgical forecast. This is, however, a complicated question that does not have a generic answer.To study the question on sampling a simulation environment was built including a synthetic ore body and sampling & assaying module. A synthetic Kiruna type iron oxide - apatite deposit was established based on case studies of Malmberget ore. The synthetic ore body includes alike variability in rock types, modal mineralogy, chemical composition, density and mineral textures as its real life counterpart. The synthetic ore body was virtually sampled with different sampling densities for a Davis tube testing, a geometallurgical test characterising response in magnetic separation. Based on the test results a forecast for the processing of the whole ore body was created. The forecasted parameters included concentrate tonnages, iron recovery and concentrate quality in terms of iron, phosphorous and silica contents.The study shows that the number of samples required for forecasting different geometallurgical parameters varies. Reliable estimates on iron recovery and concentrate mass pull can be made with about 5-10 representative samples by geometallurgical ore type. However, when the concentrate quality in terms of impurities needs to be forecasted, the sample number is more than 20 times higher. This is due to variation in mineral liberation and shows the importance of developing techniques to collect qualitative information on mineral and ore textures in geometallurgy."

Jan 1, 2016

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By F. Hassani, D. O’Donnell, M. Momayez, P. Guevremont

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with miniature seismic reflection technology (MSR) developed and patented at McGill University primarily for thickness measurement of this heterogeneous liner. MSR is also capable of providing information regarding the quality of shotcrete in terms of its mechanical properties such as modulus of elasticity and Poisson’s ratio. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fiber-reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring. In addition, the MSR technology has the advantage of being more accurate and more affordable compared to other non-destructive testing (NDT) systems in the market.

Jan 1, 2002

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968