Search Documents

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By Shounak Banerjee, Suresh Babu Dasari, Dharmendr Kumar, Shashank Pardhikar, Beena Rai, Venugopal Tammishetti

Recent increase in steel demand has led to the increased usage of high grade iron ores. During the mining, crushing and washing of ore, huge quantities of fines and slimes (<150 µm) are generated, majority of which is dumped into tailing ponds owing to their high alumina contents (~10-15%). Due to rapid depletion of high grade iron ore, it is the need of the hour to utilize low grade iron ore fines and slimes. These fines and slimes contain high iron values assaying 45-60% Fe. Dumping these valuable resources in ponds locks enormous land space and causes environmental hazards. The constituent minerals present in Indian iron ores comprise of hematite, goethite, gibbsite, kaolinite and quartz. Our research is focused on beneficiation of iron ore slimes through selective flocculation. We use density functional theory simulations to screen the reagents and perform experiments with screened reagents to determine the experimental conditions for effective performance of the reagents. Our studies revealed that reagents like starch, guar gum and carboxymethyl cellulose exhibit excellent selectivity in high alkaline pH range. However, the higher cost of alkali makes the process economically less attractive. In the present study, a commercial reagent from NALCO Water (Hi-Tex 83570) has been explored as selective flocculant for beneficiation of iron ore slimes in wide pH range (4-11). However, the reagent was also found to be the most selective in alkaline pH range only. Full factorial design of experiments was done considering three parameters namely, pulp density, flocculant dosage and settling time. Regression models were developed for yield, iron grade, alumina grade and iron recovery in the concentrate, using experimental results. Further parameter optimization was done to achieve high Fe recoveries and low alumina recoveries. The optimal parameters thus arrived at were validated with the experiments. We were able to achieve a concentrate grade of 60.0% Fe and 5.1% Al2O3 with 68.8% Fe recovery from a feed containing of 53.1% Fe and 8.9% Al2O3. The performance of flocculant Hi-Tex 83570 was also compared with reagents starch and guar gum.

Jan 1, 2018

By Mike D. Riley, Alan V. Bell, Ernest K. Yanful

Acid mine drainage (AMD) research under the MEND program has been ongoing since 1988 at the Heath Steele Mines waste rock piles including sulphide material, outside Newcastle, NB. In 1989 approximately 10,000 mt of waste rock was placed on a prepared sand base with an underlying impermeable membrane. The waste rock pile was heavily instrumented for measuring oxygen concentrations and temperatures. In September 1991, a composite soil cover designed for the Heath Steele climatic conditions, using local soils, was placed over the pile, creating a totally enclosed system. Moisture content and oxygen probes were installed within the composite soil cover to monitor changes within the soils over time, while two large-size lysimeters were installed below the cover to monitor the hydraulic conductivity of the cover. The waste rock site has been monitored on a monthly basis since installation of the cover, for performance of both cover and waste rock. The monitoring shows very clearly that the placement of the composite soil cover has had a major impact on the generation of AMD. Major reductions in temperature and oxygen concentrations within the waste rock pile indicate that the cover has significantly inhibited the oxidation reaction that generates the AMD. Performance data have shown that the cover has maintained its integrity under the climatic conditions of the area.

Jan 1, 1995

By S Sims, A Stradl, G Hope, B Lacouture

Column flotation cells have been installed in numerous base metal operations around the world. The majority of these cells utilise conventional air-only spargers to introduce air into the bottom of the column. The recent development of instruments to measure the bubble characteristics in these columns has provided a renewed understanding of column behaviour. These new tools provided insight into why the columns at Red Dog Mine had never performed up to expectations. After efforts to optimise the spargers failed to substantially change the bubble size and air efficiency, alternate sparger systems were investigated. The Metso Minerals CISA Microcel sparger system appeared promising and was selected for a full-scale plant trial. The Microcel sparger system was originally developed for the coal industry at the Virginia Centre for Coal and Minerals Processing. In October 2003, a Microcel was retrofitted into one of two 3.66 m diameter flotation columns in the zinc retreat circuit at Red Dog Mine. The operation of the two different sparger systems in parallel allowed a detailed comparison. This paper discusses the performance of the Microcel based on the data collected during several detailed surveys. Bubble size measurements carried out in the pulp zone using the McGill University bubble viewer showed a significant difference in bubble size. The mean Sauter diameter of the bubbles decreased from 3.4 mm for the jetting-type sparger to 1.9 mm for the Microcel sparger. The overall recovery and the recovery by size fraction for both valuable and gangue minerals were compared. Paired t-tests demonstrated that the Microcel column produced a higher concentrate grade (0.6 per cent zinc absolute) and a higher unit recovery (2.8 per cent zinc absolute) than the existing Canadian Process Technologies Inc (CPT) SlamJet column. These improvements provided a payback period of 1.5 months for the $109 000 investment.

Jan 1, 2005

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By M J. Noy

The automated measurement of rock fragmentation particle size distribution in the muck during muck excavation has been developing over the last 16 years. The introduction of stereo camera imaging of the muck has provided improved automated particle segmentation for image-based measurement algorithms. Recently, a new vision system processing algorithm has been developed. The inclusion of 2D texture in the analysis has provided a significant improvement in the definition of the finer size fractions, which has resulted in the automated analysis no longer requiring calibration.The previous stereo vision system algorithm required analysis calibration to account for poor ‘small particle’ definition in the 3D surface profile. This was because of the depth perception limitations of the stereo camera system at greater than 8 m. The new algorithm has been implemented on a number of shovel-installed vision systems, and the algorithm’s performance in automated analysis has been assessed against a diligent manual analysis of the same fragmentation images. The new algorithm provides improved distribution resolution and accuracy.CITATION:Noy, M J, 2015. Evaluation of a new vision system algorithm for automated fragmentation measurement from a shovel, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 721–726 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Jerome P. Downey

The Indium Corporation of America - Colorado School of Mines Indium Separation Technology was evaluated as a potential means of treating smelter flue dusts stockpiled at the Pintlar Corporation property in Kellogg, Idaho. The patented technology represents a method for segregating the contained indium, lead, and other metals in forms acceptable for downstream processing and recovery. Separation is effected by treating the dust with metallic sodium in a bath of molten lead. Process effectiveness was measured by determining the relative distribution of key metals between the bullion and dross products at small pilot plant scale. The study indicated that application of the technology to the Pitlar samples results in a highly efficient concentration of lead in the bullion, while indium is collected in the dross. The distribution of other key metals between the bullion and dross products and the effect of varying selected process parameters are also discussed.

Jan 1, 1994

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. M. Matos, C. Volzone

For industrial use, the smectite clays are usually treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present paper, a sample of brown smectite from Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5M, clay/acid solution ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. The samples were characterized by scanning electron microscopy (SEM), energy dispersive X-ray detector (EDS), stereomicroscopy, Cation Exchange Capacity (CEC), Thermal Analysis (TG/DTA), and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d(001). The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment. Thus, clay can be used in products with high added value.

Jan 1, 2015

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By L. Naude, J. Cloete, S. Engelbrecht

The results of an investigation evaluating whether an industrial plant, currently operating using sodium isobutyl xanthate (SIBX) as primary collector for sulphide minerals (mainly chalocopyrite), could adapt to operate using an alternate primary thiol collector without compromising plant and metallurgical performance. Initial laboratory scale flotation tests identified commercial dithiophosphate (DTP)-based and thionocarbamate (TC)-based collectors, that when blended, showed potential to replace the incumbent SIBX primary PGM collector. Industrial plant trail results show that there was no deterioration in recovery of 4E PGMs, even at a lower concentrate grade when operating the plant on the identified (DTP + TC)-based collector blend compared to SIBX. The effect on Cr2O3 content in the final concentrate was also found to be negligible. The (DTP + DTC)-based collector blend also showed promise in terms of plant adaptability in accommodating a new primary specialty collector blend. These observations highlighted the potential of replacing xanthate primary collectors with alternate thiol collector blends for PGM flotation. Keywords: PGM, xanthate replacement, specialty collector, sodium iso-butyl xanthate (SIBX), dithiophosphates (DTP), dithiocarbamates (DTC)

Jan 1, 2020